Search Documents

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By Takashi Furuyama, Sukeyuki Mori, Takafumi Okuma, Norio Hashiguchi

The Tower mill KD-3 is an improved version of the laboratory mills VD-1, KD-1 and KD-2 in which the classifying column has been modified to ensure a quick discharge of products from the comminution section and, on the other hand, a better separation of coarse and fine particles; the latter being collected in a cyclone with a central spiral ribbon. To level the circling airflow through the classifying column and have a strict control over the maximum size of collected particles, a series of experiments was carried out, modifying the internal structure of the column: insertion of a vertical plate, a cone, or a horizontal net. The relationship established between the maximum size of products collected in the cyclone and the duct airflow rate indicates that, independently of the latter, the insertion of a cone in the classifying column could stabilize the maximum size of products collected in the cyclone around 15.1 - 17.5µm. With a horizontal net, the maximal size could be reduced to 8.4 - 11.3µm. This occurrence might result from the collision of coarse particles blown from the comminution zone with the base of the inserted materials and their settling down the bottom of the classifying column.

Jan 1, 2003

By T. Saastamoinen, N. Heino

"The Olserum deposit located in Sweden hosts an indicated mineral resource of 4.5 million tonnes over 0.6 % TREO, exhibiting a relatively high proportion of HREE. Beneficiation of a composite drill core sample was studied in the flowsheet of magnetic separation of magnetite followed by REE minerals flotation. Primary testwork was performed to select an effective REE mineral collector and then the parameters of grinding size, collector and depressant dosages, slurry pH and density, conditioning time and temperature, and flotation time were tested for optimization of REE flotation. The studies of process mineralogy showed that the REE-bearing minerals monazite, xenotime and apatite were successfully enriched from the concentrations of 0.6%, 0.31% and 2.6% in the feed to those of 17.0%, 8.9% and 65.0% in the concentrate with the recoveries of 79.0%, 81.3% and 71.0%, respectively. INTRODUCTION The Olserum deposit located in Sweden comprises lower grade placer material with higher grade apatite-magnetite veins and hosts an indicated mineral resource of 4.5 million tonnes at 0.6% TREO, with 34% of that being HREO (EURARE, 2017). The mineralization was studied by Andersson et al. (2018). At early stage, high-temperature REE is characterized by abundant monazite-(Ce) and xenotime-(Y) coexisting with fluorapatite and subordinate amounts of (Y,REE,U,Fe)-(Nb,Ta) oxides. During a subsequent stage, allanite-(Ce) and ferriallanite-(Ce) formed locally, partly resulting from the breakdown of primary monazite-(Ce). Alteration of allanite-(Ce) or ferriallanite-(Ce) to bastnäsite-(Ce) and minor synchysite-(Ce) at lower temperatures represents the latest stage of REE mineral formation. The mineralogy and beneficiation were firstly studied by GTK Mintec in the EURARE project for a composite drill core sample. The Olserum is considerably smaller than the Norra Kärr deposit. However, REE are hosted by xenotime and monazite, both of which have well established processing pathways, and meanwhile, the Olserum has a high contribution of the high value critical REE (dysprosium (Dy), yttrium (Y), neodymium (Nd) and terbium (Tb)), which provide a unique advantage for its exploration (Tasman Metals Ltd., 2013). In this paper, flotation of the REE minerals in the Olserum ore was studied."

Jan 1, 2018

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

By I. Gombköto

Mining and mineral processing operations are usually generating huge amount of tailings. These tailings often gives lots of maintenance work in order to protect environmental resources from heavy metals slowly leaching out of tailing are due to Acid Rock Drainage (ARD) process. Handling leakage could be active or passive such as using of Permeable Reactive Barriers (PRB). PRB?s are used worldwide treating underground contaminations, using different type of matrix materials. All generally used matrix material has its advantages and disadvantages such as selectivity, sensitivity of precipitation generation or not satisfying hydraulic conductivity. Nowadays cheap and effective matrix material which is ignorant to pore plugging caused by precipitation within the PRB could be one solution to the demands of the industry. The authors have been carried out an investigation at University of Miskolc on lignite as high humid acid containing material for determining the ability of heavy metal adsorption and pore plugging resistance. Moreover, using hydraulic and chemical simulation methods, complete PRB dimensioning protocol based on new lignite matrix had been introduced. Within the frame of this paper the results are going to be discussed.

Sep 1, 2012

By Yi Ran Zhang, Nawoong Yoon, Brent Hilscher, Maria Holuszko

"Ore sorting technology has been rapidly advancing in recent years. Improving expected mill feed grade has a significant benefit to project returns, and can no longer be ignored. When there is an increase in the mill feed grade while maintaining the same throughput, the mine will be able to process much more metal and improve the floatation recovery. There are many more factors that contribute toward the economics of the project by implementing sensor-based sorting technologies covered in this paper. This paper reviews the economic impact on an underground copper-silver deposit with references to the concept of ""profit recovery,"" which is the measurement of recovery based on rock profitability rather than just metal content. The economic impact of sensor-based sorting is discussed in detail throughout the paper. The preliminary economic evaluation of the project compares the mine's base case design versus a design incorporating sensor-based sorting. The paper's primary focus is on economic impacts rather than the explanation of the sensor based sorting results. The sorting data is presented on a scoping level and using a sensor-based sorting study where the best possible results are used for obtaining the grade recovery curves. Also, the breakdown and analysis of the project economics are based on the operating cost available from the particular operation. Any assumptions taken into consideration are also outlined and discussed. INTRODUCTION The mining industry has been adopting Sensor-based ore sorting technology fairly rapidly in the recent years. The ability to increase mill feed grade by rejecting waste grade rocks early in the processing stage is proving to be revolutionary for some operations. These potential outcomes should not be overlooked by both producing operations and prospective projects, thus leading to a wide range of studies on ore sorting. The answer to this is the creation of a new term and concept - Profit Recovery™."

Jan 1, 2018

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By H. R. Manouchehri

Sustainable development requires the optimal use of natural resources and recycling of the wastes. In fact recycling is the final productive use of obsoletes. ELVs, obsolete appliances and industrial wastes have become important resources for production of iron and steels, non-ferrous metals, and composites. Within shredding plants, these obsoletes are firstly shredded to the pieces and then processed to recycle different materials, especially ferrous and non-ferrous metals for metallurgy. Traditional and new developed mineral processing technologies are nowadays used for recycling different materials from waste effluents. Shredding and separating plants are currently recycle the wastes by make use of different technologies to mainly produce raw material for metallurgical application. However, other non-ferrous components are also treated for energy conservation and protecting environment. Currently, recovery in shredding and recycling plants maximises to 75% and about 25% of the feed is land-filled. However, recycling rate must be increased in due to the economical, environ-mental and social concerns. A comprehensive study for recycling, with especial focus on ferrous metal recovery, was sup-ported by Swedish Environmental Agency (MISTRA) to look at possibilities to increase the recycling rate and to reduce the amount of disposal. Part of this study was dedicated to study the shred-ding plant facilities and to look for possibilities to improve the quality and quantity of the shredding product streams. The aims were to improve the quality of ferrous scrap (apparent density > 0.9 and Cu<0.25%) for iron and steel production as well as having better quality for non-ferrous metals through the recycling schema, and finally to treat the shredder residue (SR) to recover metals and plastics to reduce the disposals. This paper summarises the results of sampling and conducting separation tests for improving the recovery of the ferrous and non-ferrous metals. The results indicated to be possible to obtain high quality ferrous scrap at recovery of 88%. However, the total recovery for metal scrap has reached 93%. Furthermore, test results on fine, P< 8mm, shredding residue (SR) showed promising prospect in recovery of metals and protecting environment by physical separation, i.e. electrical separation technique.

Jan 1, 2014

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

By Bisweswar Das, Barada Mishra, Hrushikesh Sahoo, Swagat Rath

Banded hematite jasper (BHJ) containing 45.2% Fe, 32.64% SiO2, 0.63 % Al2O3 and 1.25 % LOI is found difficult to beneficiate either by magnetic or flotation techniques due to fine intergrowth of jasper with hematite. Phase transformation by reduction roasting with activated charcoal followed by low intensity magnetic separation to achieve a suitable iron concentrate has been attempted in this study. The mineralogy of the ore and different roasted products has been studied by X-ray powder diffraction (XRD) and scanning electron microscope (SEM) to understand the reduction mechanism. The magnetite formation is observed at 850ºC while metallic iron appeared at a higher temperature. The effects of reduction variables such as reduction time (30-270 min), temperature (750-1050ºC), and reductant (1-12 %) using activated charcoal are studied. An iron concentrate with 64.65% Fe and 55.8% recovery could be obtained under optimum conditions of temperature: 850ºC, time: 1.5 h, and reductant: 6% by weight.

Jan 1, 2014

By E. Szelag

The adsorption and stabilization of mineral dispersed systems by using Pluronic copolymers with different molecular weights and EO content has been studied. The role of sequential adsorption of EO-PO copolymers and cationic surfactant (CTAB) on the carbonate particle properties and in determining the stability of their suspension was studied with particular attention to the conformation of the polymer at the solid-liquid interface. The purpose of this work was to investigate the flocculation phenomena, influence of polymer molecular size on stability of suspensions of magnesite and dolomite and the effect of addition mode of polymer and surfactant. The suspension stability measurements and the determination of sedimentation speed were carried out using an optical analyser (Turbiscan). In most of investigated cases, the biggest floccs and the fastest sedimentation were found for low concentrations of copolymers.

Jan 1, 2014

By V. V. Lvov, L. S. Chitalov

"The purpose of the research is intensification of physico-mechanical ore properties determination for ball grinding processes in comminution circuits. The research presents comparative studies aimed at intensification of Bond Ball Mill Work Index (BWi) determination, such as testing technique of Ahmadi and Shahsavari, Berry and Bruse, Gharehgheshlagh, Horst and Bassarear, Kapur, Magdalinovich. The subject of the research is a test procedure of apatite-nepheline, copper-nickel, gold-sulfide and iron ores for the Bond ball mill index. The Bond Ball Mill Work Index for the material firstly was determined by standard Bond test methodology. Two the most promising testing techniques - Ahmadi and Kapur testing techniques - were modified. For the Ahmadi technique it was proposed to pay attention to the circulating load, which should be stabilized on the value of 250% as fast as possible. Two methods were put forward to quicker stabilize the circulating load. For the Kapur technique it was proposed to use empirical coefficients, which is determined especially for the apatite-nepheline, copper-nickel, gold-sulfide and ores. The modified Ahmadi and Kapur techniques require no more than two cycles of ball grinding to determine BWi (while normally 6-8 cycles are required) and less than 5 kg of initial feed. The suggested modified Ahmadi and Kapur techniques allow to intensify the physico-mechanical ore properties determination for ball grinding processes and BWi test costs considerably, which makes them useful for mass sampling and monitoring strength properties of ores entering a concentrating mill. INTRODUCTION When designing concentrating mills, the choice of the technological scheme for ore pretreatment, particularly the type, quantity and size of the main process environment, the determination of optimal grinding conditions and the calculation of equipment load are carried out by preliminary studies of grinding in semi-industrial or laboratory-scale plants. Semi-industrial tests on full-scale plants provide the most reliable information for calculating specific loads for equipment. However, this requires a significant amount of ore samples, a high labor costs and the pilot plants. Thence the most researchers performed grinding tests with small laboratory equipment using small ore samples."

Jan 1, 2018

By J. J. Cai

The status of fossil fuel and secondary resource in metallurgy industry in China were reviewed, and conversion efficiency of fossil fuel, utilization technologies of secondary energy were studied. Fossil fuel, accounting for over 90% of energy structure in metallurgy industry, took in the highest flight in China, and a great deal of which was converted to secondary energy through the equipment of blast furnace and coke oven. These secondary energy which were mostly made of blast furnace gas(BFG), coke oven gas(COG) and Lindz Donawitz gas(LDG) occupied about 30% of total secondary energy. The way enhancing fossil fuel conversion efficiency, secondary resource recovery and the secondary energy such as BFG, COG, LDG utilization promoted to save fossil fuel was discussed in this paper. And efficient use of lower caloric value fuel was studied, such as preheating combustion air and fuel, generating electricity power etc. and regeneration purposes of high-caloric fuel was also researched, for producing hydrogen, methanol or direct reduction iron etc. The using model of secondary energy at iron and steel works was presented as fuel and chemical materials. The results suggest that utilization of these energy efficiently and reasonably could help to energy saving and environment protecting.

Jan 1, 2014