Search Documents

By Mohini Patel, Jahnavi Parmar, Pranav R. T Peddinti

Expansive clays pose a variety of geotechnical problems. Although the admixture stabilization is proven to address their problematic swelling and shrinkage characteristics, the influence of unsaturated condition on the engineering performance of these soils needs further research attention. In addition, highly saline soils with high organic content would further alter their performance. A similar soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, India. High salinity in the in-situ expansive soil of basaltic origin and the prevailing unsaturated condition, enforces the engineers to look out for possible soil treatment methods. In this regard, the present work attempts to analyze the unsaturated behaviour of this soil when fly ash is used as an admixture. A comparative study for stabilized and unstabilized mixes is performed in terms of their unconfined compressive strength, electrical conductivity, swell characteristics and California Bearing Ratio.

May 1, 2022

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Patrick J. Hannigan, Seth Robertson, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) and the conventional Bi-Directional Load Test (“BDLT”) are full-scale load tests where loads are applied bi-directionally to the foundation element. The BDLT uses an embedded loading source consisting of a jack assembly with one or multiple hydraulic jacks located between two steel bearing plates. As the jack(s) within the jack assembly is/are pressurized, the plates receive the load from the jack(s) and transfer these loads to the foundation element. In the case of the TLBT, the loads are also applied bi-directionally to the foundation element. However, in the TLBT case, the loading source is located above the foundation head. With the TLBT’s non-embedded and reusable load assembly, the loads are applied to the foundation using the steel shaft bearing and base bearing plates cast within the foundation. These plates are connected to the load assembly at the foundation head via Grade 75 or Grade 150, threaded, steel bars. This paper presents comparison results from a full-scale load test performed by both bi-directional load testing methods on adjacent test shafts. Details regarding subsurface conditions as well as test shaft construction and installation are included for the comparison tests. Test results and corresponding analyses are presented and discussed in detail.

Sep 8, 2021

By Masahiko Yamaki, Takahiro Yamanashi, Hijiri Hashimoto, Hirochika Hayashi

"In this study, the authors used heat conduction analysis with the aim of quantitatively evaluating whether treating improved ground with cover soil is an effective measure for maintaining strength development in the surface layer of improved ground after constructing cement treated soil for the winter season. This report describes a simple procedure to evaluate covering soil thickness, which is necessary for the strength of the surface of cement treated soil, by using the freeze index and both the water content ratio and dry density.INTRODUCTIONIt was reported that when ground improvement using cement is performed in winter in a snowy cold region (Fig. 1 photo, Fig. 2), the uppermost 1 m of the improved ground (i.e., the cement-treated soil) tends to become prone to solidification failure from exposure to the cold air during curing (Hashimoto et al. 2006). In light of this, our research laboratory conducted unconfined compression tests using curing temperature as a parameter of analysis on improved ground toward understanding the influence of curing temperature (ambient air temperature) on the strength improvement afforded by ground improvement.The authors found that if the curing temperature is maintained at 0°C for the first 28 days after improvement and then at 5°C for the next 337 days after improvement, the improved ground is expected to have 90% of the unconfined compressive strength of improved ground whose temperature was maintained at 20°C for the first 365 days after improvement (Hashimoto et al. 2011)."

Jan 1, 2015

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By F Debidin

The progressive rise of an H-pile during driving of an adjacent pile is described in this case history in which piles 15 to 18 m long were driven to end-bearing for the foundations for a 230 m long building. The use of a reaction beam-soil anchor system for compression load tests is discussed. The results of static load tests to determine pile capacity are compared with those obtained by the Pile Driving Analyzer and by theory. Unusual high temporary compressions were observed by field control staff. Proof testing was necessary to determine the need for restriking of some piles in which rise had occurred.

Jan 1, 2010

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By RavikiranVaidya, Vishal Dhamecha

Low Strain Pile Integrity Testing has been used in India since 1990’s and several have tried to demonstrate the utility and benefits of this method. However, use of this technology was limited till 1998 as not enough data maybe was not available to justify its use and application on major infrastructure and real estate projects. The first author has done significant work in this method resulting in its use in practically all sectors of the industry that use concrete bored pile foundations as a supporting element. The paper explains various signal enhancers or modifiers involved in processing of low strain test data and its implication on the final output. It also describes how the method can lead to abuse or can provide poor interpretation if incorrectly used. The current effort is to demonstrate that data collection and evaluation becomes complex with changes in soil stratum and pile profile. The paper highlights the present testing practices and provides a guideline for classification of pile integrity into few simple categories in Indian context rather than writing complex interpretations.

Sep 1, 2022

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By Manfred Schoepf

"Construction projects using the most advanced technologies and organizational structures demand intelligent construction machinery. In this process, automation technology plays an increasingly important role. Many components used in the automatic control of machine components are being taken for granted to such an extent that operators are often even unaware of their existence. Innovations in micro-electronics, such as process computers, programmable logic controllers (PLC) or intelligent sensor systems, have by now found their way into construction machinery. Construction machines are indeed becoming ever more intelligent. Key electronic applications in foundation engineering machines can be summarized into the following main categories:- Data acquisition- Online monitoring of the equipment status- Remote data transfer- Satellite-based Navigation System for Positioning and Documentation- Process controlData acquisitionThis includes machine-specific operating data, such as engine speed or operating temperature, operating hours, display of fuel consumption, but also the acquisition of process-specific data, such as pile depth, pile inclination or slurry volume.Monitoring the equipment status onlineAn extremely important aspect is the acquisition of fault data. In conjunction with available remote data transfer systems, malfunctions can now be searched and diagnosed by specialists anywhere in the world to provide assistance to the site personnel.Remote data transfer - “Anywhere, from everywhere”All previously referred to parameters can be stored on appropriate storage media inside the machine. The customer also gets a worldwide, safe access via an internet browser to check the current status of the equipment, anytime, anywhere.All data can be saved on a secured web server for documentation and further analysis. The internet connection of the equipment through a special module (DTR Module) additionally allows the user to operate a local, password-saved WLAN hot spot at the construction site and exchange data between equipment, tablet and internet.The web based system, which is named “WEB-BGM Equipment Management” in the Bauer Group, can do much more than only communicating with one machine."

Jan 1, 2015

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By H. (Sam) Salem

A site investigation for a wide and tall hotel building, in the San Juan Bay area, Puerto Rico, indicated a soil profile of silty clay on sand, soft and loose enough to require piled foundations. The apparent uniformity of the soil profile across the site indicated that a single pile driving and termination criterion could be applied to the installation of the piles ? driven precast concrete piles. Because of the size of the site and importance of the project, the project also included a static and dynamic testing programme. The dynamic monitoring using the Pile Driving Analyzer (PDA) verified a consistent hammer operation. However, the results of the static loading tests showed significant and inconsistent variation in pile capacity between locations and little correlation between end-of-driving and restrike penetration resistances (blow-counts) and pile capacity. Therefore, it was not possible to rely on a simple depth and blow-count termination criterion for the site. In contrast, pile driving response in terms of measured reflected force and mobilized resistance coupled with CAPWAP analysis gave a reliable correlation to the results of the static loading tests. As presented in the paper, the dynamic testing programme was enlarged and used to develop and verify a complex set of termination criteria tailored for the multitude of conditions encountered across the site to achieve and ensure economical and safe pile installation.

Jan 1, 2008

By Dominic Ammon, Mark Rothbauer, Paul Landers P. E.

Across the Potomac River from the location of the DFI47 Annual Conference (October 2022), in Alexandria, VA, two large permanent anchored walls with a decorative shotcrete face were recently constructed for the North Hill project, a new multi-family and townhome development. The project was executed with a design-build approach for the Fairfax County Redevelopment and Housing Authority with review by the Fairfax County Geotechnical Review Board. The project was constructed in highly variable Potomac group sediments that include high plasticity clay/silt terrace deposits overlying coarser grained materials. The soils were over consolidated and exhibited potential for slickensides from relief of horizontal stresses from past erosion. The wall system was designed to include deep soldier piles and permanent long strand anchors considering past slope instability in the area. As the construction progressed, problematic soil conditions and water issues required modifications to drilling methods. The two permanent walls spanned 800 and 1,000 feet long with a maximum height reaching 40 feet.

Oct 1, 2022

By Orestis Zarzouras, Amalia Giannakou, Jacob Chacko

"When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.IntroductionThe Izmit Bay bridge, a 3-km-long suspension bridge that crosses Izmit Bay in Turkey, is planned to be constructed in one of the most seismically active places in the world. The south approach structures for the Izmit Bay Bridge along the western side of the Hersek peninsula bring the bridge down from on the order of El. 60 meters at the South Anchorage to an elevated embankment approximately 1.3 km farther south (Figure 1). The south approach structures are located within a zone of secondary deformation around the primary trace of the North Anatolian Fault. The concept design team has developed a concept design for a “viaduct” structure that consists of 10 spans with lengths varying between 136 m and 100 m and two back spans one of 125 m, attached to the main bridge and the other of 74 m attached to the south embankment."

Jan 1, 2017

By Jack Taggart, Chris Barker

Pile load testing strategies for large infrastructure projects and multi-phase building developments have historically justified cost and programme benefits for undertaking advance preliminary and working pile load testing. However, more recently piling and pile load testing strategies have included assessment of the embodied carbon to understand and present the carbon savings that can also be achieved. This paper gives an overview of the factors contributing to carbon and emissions in the construction of bored pile foundations and presents the methodology taken in assessing embodied carbon as part of the pile load testing strategy for a multi-phased building development in London. Potential embodied carbon savings for various bored pile types and load testing strategies are discussed alongside alternatives and other considerations including pile re-use and carbon offsetting to inform continual improvement for future projects.

May 1, 2022