Search Documents

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By C. Jewell, G. H. Rupay

"67 - 2:15-3:00Regeneration of Hydrochloric Acid from Waste Pickle Liquor Using a Fluidized Bed Reactor System. G. H. RUPAY and C. JEWELL, Dominion Foundries and Steel Ltd., Hamilton, Ont.The disposal of acidic waste liquors from pickling processes has always been a problem for the steel industry. With increased awareness toward environmental control and the problems acidic wastes create, processes utilizing recovery and regeneration of the waste acids are becoming more popular. This paper describes the Keramchemie/Lurgi process for regenerating hydrochloric acid from waste pickle liquor using a fluidized bed reactor system. The process parameters are outlined, together with a brief description of the equipment. This is followed by a discussion of the operating problems and concludes with economic data."

Jan 1, 2000

By Andreas Zielonka

To meet the increasing demands of the quality and long term stability of technical systems also the applied materials have to full fill higher standards. This is of special importance where the function of a whole system depends on the reliability of the used materials for example for connector systems in automotive, computer and other electronic equipment?s. In most cases for connector systems electro deposited top layers are applied. To improve the quality of the applied layers new electro deposited systems are developed. One important field of research are the development of composite materials as dispersion coatings and multilayer systems. Multilayers are systems with a high number of single inter-layers of different metals or alloys with the wide chance of the alloy composition. As gold is one of the most important contact material for high quality connector systems it is used as basis for the development of multilayer systems. For the electrodeposition of multilayers two different methods can be applied, the single and the dual plating process. As in the dual plating process two different electrolytes are used, the single plating process allows the formation of multilayers from one electrolyte. In the presented research results cobalt and nickel are used besides gold for the formation of the multilayers. The properties of the layers can be influenced in a wide range by the change of electrolyte composition and the process parameters as current density, current waveform, temperature, hydro-dynamic conditions at the electrode surface and by the number and thickness of the inter layers of the deposited materials. The paper describes the fundamentals of the electro deposition of multilayer systems. For the investigation of the properties of the multilayers different techniques are applied. One of the most important parameter are the thickness of the total layer and of the applied sublayers. The thickness of the sublayers can be varied between a few nanometers up to micrometers. The wear resistance, the contact resistance and the plug-in forces are measured as these parameters are important for the technical application of such layers. For the description of the structure composition and surface properties the sample where also investigated by scanning electron microscopy (SEM), energy dispersive x-ray-analyses (EDX) and glow discharge optical spectroscopy (GDOS). The paper shows that the deposition of gold based multilayers is possible and that the properties of such systems can be varied in a wide range what opens new fields of applications of such materials.

Oct 1, 2003

By K. V. Gow, F. A. Jerabek

"THE NOVA SCOTIA TECHNICAL COLLEGE has been granting degrees in mining engineering since 1909. The college was established in 1907 to provide the final two years of the undergraduate program in engineering the earlier years of which are given at several small universities scattered around the Atlantic Provinces. Since the beginning of the program, 251 Bachelor of Engineering degrees have been awarded in mining engineering. Although the average class size has been small, increases in enrolment in the past few years have resulted in Nova Scotia Technical College being the second largest mining department in Canada, based on the number of graduates per year. This year 18 students received B.Eng. degrees, and next year 17 will graduate.In 1968, it was necessary to make a decision on whether or not to abandon, for economic reasons, the program in mining engineering. For several years enrolment had been very low and resignations among the mining engineering staff created a situation in which the program could easily have been dropped. However, it was decided to continue mining engineering, as it was the only such program in the Atlantic Provinces. New staff members with many years of practical experience in the mineral industry, not only in Canada but in the U.S.A., South America, Africa and the U.K., joined our department. At the same time the enrolment in mining engineering began to increase significantly."

Jan 1, 1972

By D. Zagidulin

Short term electrodeposition experiments (up to 80 min.) at two current densities 220 and 275 A/m2 with varying concentrations of thiourea and glue were performed to determine the optimum levels of glue, thiourea and current density for industrial copper electrorefining. White Light Interference Microscopy was used to acquire digital images of the morphology of the electrodeposited copper. Scaling analysis was employed to pa-rameterize the morphological information encoded in the images. The limiting rough¬ness, *, the critical scaling length, Lc, and the aspect ratio, 4*/ Lc, were determined as a function of the deposition time and the amount of organic additives. These parameters were used to calculate the dynamic exponent, B, the roughness exponent, 1/z, and the as¬pect ratio exponent, y, plotted as a function of glue and thiourea concentrations. These 3D plots allowed us to find conditions corresponding to the minimum of B and y, at which the deposited copper is characterized by a small roughness and a dense structure.

Jan 1, 2007

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By C. A. Pickles, K. Mackowiak

Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario was carbothermically reduced in a microwave system to produce a ferrochromium alloy. The as-received ore contained 43.0% Cr2O3, 19.9% Fe2O3, 14.5% MgO, 13.4% Al2O3, and 7.0% SiO2. Activated charcoal was utilized as the reducing agent. Firstly, TGA/DTA and permittivity studies were carried out in order to determine the relationship between the reduction process and the microwave susceptibility. Secondly, microwave reduction experiments were performed on the chromite ore. The variables investigated were; the amount of carbon, processing time, input power and type of atmosphere. A maximum chromium grade of 76.1% and a chromium metallization of 82.7% were obtained for a processing time of 20 minutes, a power input of 800 W, and a carbon addition of 15% in an argon atmosphere.

Jan 1, 2017

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By Roger Francis

There is increasing use of acid leach extraction methods at elevated temperatures and pressures by the mining industry. In many locations there are limited supplies of fresh water, and waters with higher chloride contents must be used, making conditions more corrosive. The fluids downstream of the main autoclave are hot, acidic, oxidizing and contain chlorides and present a challenge to the mining community to ensure reliable operation. Zeron 100 is a high strength superduplex stainless stee, that offers high corrosion resistance at a cost effective price. The paper presents a combination of laboratory data and service experience, particularly in the aggressive fluids found in downstream processing.

Jan 1, 2010

By A. Diaz, Minera Los Pelambres, C. G. Salinas, G. Leinenweber, F. Diaz, D. Rojas, R. Bernal, O. Jimenez

"Los Pelambres Mine (MLP) is located in the IV Region of Chile, a semi-arid region where water plays a key role in operations as a scarce resource and is vital for the sustainability of human life, animals and ecosystem. The conventional flow meters installed on pipes at MLP can fail to provide an accurate measurement due to corrosion and/or fouling on the inner wall or presence of elements in the water such as acids, salts and suspended solids. Conventional flow measurement methods require the inner diameter to be known, however it is not always possible to assess its real value due to scaling, fouling, corrosion, etc. Here we present a novel methodology to solve these problems, which consists of the measurement of flow by a method that does not require the internal area of the pipes: the fluorescent tracer dilution method. In addition, the fluid velocity can be determined by the transit time of a radioactive tracer method. With the flow rate and velocity, the equivalent area is determined and thus the equivalent internal pipe diameter as well. This methodology was applied in a recirculation pump station, for mineral processing from the El Mauro tailings dam.This work demonstrated adequate correlation between measurements from fluorescent tracers and velocity measurements from radioactive tracers, both of which lead to the assessment of the internal diameter of pipes with scaling. The results of both methods disagree with the data provided by the flowmeter installed on the line due to its miscalibration. This information is useful in validating and correcting the information provided by online flowmeters of all water and solutions transport processes in filled pipes.INTRODUCTIONPresently, the need to optimize water resources is increasingly ever important, due to various reasons such as water scarcity, community empowerment, an increased use of water for mining processes and environmental considerations. Taking into account those main considerations, Los Pelambres Mine decided to focus on water conservation to avoid losses of this vital element. They decided to demonstrate that all of the systems that used water (flow meters, pipes, pumping stations, lagoons, etc) were in good condition and that no evitable loses of this important resource occurred. A plan was proposed to conduct a “hydraulic assessment” of fluid flux and water speed at different points and courses at the mine, with the purpose of obtaining hard data to support, verify and correct the information provided online from specific instrumentation dedicated to those purposes. The final goal was to manage the water resource basin in a sustainable way, based on cross-checked information. The chosen points are representative of the processes present in the mine, such as recirculating water stations at different operating conditions and surface water courses, where the fresh water capture systems operate."

Jan 1, 2016

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By B. Daniels, A. Tieu, W. Yan, B. Ren, M. Vijay

"Plasma or thermal sprayed coatings are becoming more widely used in a wide range of industrial applications. The preference to use thermal sprayed coatings is mainly attributed to its superior wear, and corrosion resistant properties akin to hard chrome but without the harmful health implications of chrome in the coating process. Specifically, High Velocity Oxygen Fuel (HVOF) plasma sprayed Tungsten Carbide & Cobalt (WC/Co) coatings are presently being tested on aircraft landing gear. This coating can be efficiently applied and is highly resistant to corrosion and wear. However, HVOF coating's durability also makes it difficult to be stripped for inspection and overhaul. Current coating removal methods usually involve a multi-step process whereby the coating must undergo diamond wheel grinding, chemical dipping, grit blasting, ultrahigh pressure (UHP) 380 MPa (55 Kpsi) water blasting, and subsequent chemical dipping, depending on the type and thickness of the coating. As explained by Yan, et al [l]"" a unique method has been developed for removing HVOF coatings with the use of only water. The method consists of modulating a stream of water at a pressure of only 69 MPa (10 Kpsi) with ultrasonic waves to generate a forced pulsed waterjet. The resulting cyclic loading of the hard coating due to the impact of the water pulses easily causes it to flake off the substrate. This paper will briefly describe the fundamentals of the forced pulsed waterjet technique with an emphasis on insitu applications of the removal of various plasma and HVOF coatings."

Jan 1, 2006

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By G. M. Humphrey

It is a great honour and privilege to be here in this distinguished company of the outstanding men in the mining industry and the political life of Canada. I fully recognize that I am so honoured as a symbol of the combination of American and Canadian leaders in industry who are partners in the sponsor-ship of the Quebec-Labrador iron-ore mining development which we are undertaking, and as such I want to express our great appreciation of the co-operation and assistance we have met on every hand in Canada, and the genuine friendliness and never-failing courtesy which we are always accorded. We are quite aware that it springs primarily from the very high regard in which our partner and sponsor, Jules Timmins, and our other Canadian associates are held. Their high standing among you is well known and we quite naturally fall heir to the benefits of the great esteem in which you hold them. Jules Timmins and his long-time associate, John Knox, were the original inspiration for our participation in this venture. It was their enthusiasm and vision which caught our interest and led to our joining with them in the years of exploration and search which have brought us to the threshold of this great development where we stand today. So much has been written of the details of our exploration and plans for future development that it would bore you for me to review them further here, but there is a phase of this development, and an extremely important phase of it, which I think has passed almost unnoticed and which it may be well worth while for me to bring to your attention this evening.

Jan 1, 1951

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012