Search Documents

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By Jr. Santos, T. V. Pignaton, R. B. Gomides, W. Phillips, M. P. D. Gomes

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By J. P. Wiser

THIS paper discusses testing and quality control of milled asbestos fibre. It has been composed with the intention of: (I) Summarizing past, present and probable future methods of testing and classifying the various grades of commercial asbestos produced by the Quebec asbestos industry. (2) Acquainting those unfamiliar with the methods used for evaluating, testing and controlling the grading and the quality of Quebec chrysotile asbestos fibres with some of the physical and chemical procedures currently used for that purpose. (3) Discussing some of the complications facing the producers, such as variations in the orebody and special requirements of asbestos manufacturers. ( 4) Detailing some of the present quality control methods. SUMMARY OF PAST, PRESENT AND PROBABLE FUTURE TESTING METHODS Past During the first years of production of commercial asbestos in the Province of Quebec, fibre testing and quality control were based principally on dry screen analysis and visual inspection. These methods were gradually expanded during the period from 18, 90 to 1932. In 1932, standardization

Jan 1, 1962

By A. Himsley

This paper presents a review of the existing ion exchange resin systems for treating unclarified pregnant liquor, with particular reference to uranium extraction. A new concept of a truly continuous ion exchange system is described and operating details are given,of a 0.6.-m (24 in.) diameter pilot plant treating unclarified acid leach liquor.

Jan 1, 1977

By Engineering Staff

In 1958, the Iron Ore Company of Canada decided to proceed with the Carol Project. The ore deposits in the area are part of the highly metamorphosed southern zone of the Labrador Trough. They lie along the shore of W a bush lake, in the western part of Newfoundland-Labrador, 190 miles north of Sept-Iles. The project is designed to mine, by open-pit methods, 17,200,000 long tons of crude ore, grading 37 per cent iron, per year. This ore will be beneficiated to produce 7,000,000 long tons of concentrate, grading 66 per cent iron, of which 5,500,000 long tons will be pelletized. Production is scheduled to commence this summer. Initially, ore will be taken from 45-foot benches in the Smallwood mine, using jet-piercing production drills and large-scale blasting with "slurry" explosives. Four 13-yard electric shovels will muck the broken ore into 100-ton trailer trucks. The trailers will be hauled to two 2,000-ton loading pockets, which feed the ore into 100-ton railcars. Four ore trains, each comprised

Jan 1, 1962

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By W. R. Gunter

"INTRODUCTIONThis article documents the current non-metallic mineral s resources of Manitoba (Fig. I), and makes comparisons with currently producing deposits in North America and elsewhere in the world. Industrial minerals may lack the glamour of gold, silver or the base metals, but they contributed approximately 20070 to the value of Manitoba's raw materials, and even out-performed our petroleum industry, except during the oil boom of the early eighties (Fig. 2). Values per tonne of industrial commodities can be as high or higher than for base metal ores. Commodity prices (Canadian), listed in the February 1988 issue of Industrial Minerals magazine, are: talc $202.00 - $306.00, sillimanite $427.00; kaolin $69.00 - $270.00; garnet $175.00 - $250.00; and mica $405.00 - $540.00. The prices are converted to Canadian dollars using the prevailing exchange rates of February I, 1988. Some commodities are not sold by weight. Building stone, for example, is sold by the cubic foot. An average rough granite block, 4 ft by 4 ft by 8 ft, is worth approximately $2000 sitting on the quarry 1100r in southeastern Manitoba (Fig. 3).Thus, not all rocks that do not contain sulphides are worthless. Some may be extracted more profitably than either the base or precious-metal bearing varieties.Industrial Mineral CommoditiesThe commodities available in Manitoba are described in two categories: (1) those already in production that have additional development or expansion potential, and (2) those not in production logical information available at this time.Current Industrial Mineral ProductionThe commodities described herein are currently in commercial production in Manitoba (Fig. 4). These mineral products also have good market expansion potential provided additional geological and market research is conducted. The use of company names in reference to sundry products and locations should not be interpreted as specific endorsement by the Government of Manitoba. The numbers following the commodity name refer to Figure 1. that have good development potential on the basis of geo-"

Jan 1, 1989

By Patty Simpson, Sarah Benson

In an effort to improve consistency across the nuclear industry, over the past 10 years the Canadian Standards Association has developed a series of standards related to environmental management at Class 1 nuclear facilities and uranium mines and mills. Canadian uranium mines have been required by the Canadian Nuclear Safety Commission to align their existing monitoring programs with these standards. Orano’s McClean Lake Operation’s monitoring program, which was originally presented in the Environmental Impact Statement in 1991, has evolved through regulatory change, new scientific understanding, additional projects, and experience into a comprehensive set of monitoring requirements for effluent, groundwater, air emissions, and the receiving environment. The exercise of aligning the existing practices with the standards provided an opportunity to review and rationalize the entire program. To document the process the original “Environmental Monitoring Program Design Document” was restructured and developed as both a repository for historical information and monitoring rationalization, and also to be a living document describing on-going studies and supplementary work that are outside of the regular environmental monitoring program and may justify future changes to the program.

Jan 1, 2020

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By Tatsuya Oki

Tantalum capacitors can be found mounted on printed circuit boards of domestic appliances such as personal computers. These capacitors contain a considerable quantity of expensive metal tantalum and can be detached and liberated from printed circuit boards by impact breakers. In this study, the size and density distribution of the liberated electronic devices were investigated. Then, tantalum capacitors were recovered from other electronic devices using size separation and pneumatic gravity concentration methods. More than 70% of Newton's separation efficiency was obtained for tantalum capacitors. High Newton's separation efficiency could be also obtained for other types of electronic devices such as chip resistors.

Jan 1, 2011

By W. Beres, M. Bielawski

Recent research on the development of erosion resistant coatings has been directed to the finite element modelling of the behavior of coating and substrate, and their interface under the impact of eroding particles. The approach presented in this paper is based on advanced computer simulation techniques using ABAQUS/Explicit to investigate stress and strain at the surface and at the coating/substrate interface of multilayer coatings under single particle impact. It was found previously that solid particle erosion mechanisms are predominantly governed by the kinetic energy of the impacting particles. However, recent modelling efforts revealed that effects of various material models could be also significant. Therefore, different material models representing relevant coating and substrate properties were investigated and the effects of these models on the coating/substrate response were studied. Particularly, differences between elastic, elastic-plastic and brittle cracking model responses were assessed.

Jan 1, 2006

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

Research on alternative lixiviants for gold is ongoing; however few people have looked at complete flowsheets. Alternative lixiviants are typically applied at concentrations 50 to 100 times those required for cyanidation. The higher concentrations make lixiviant recycle a vital part of the process. In addition it is no longer feasible to rely on lixiviant destruction to produce lixiviant free clean water for recycle to the comminution circuit. Ausenco has worked with Barrick to integrate reverse osmosis into the thiosulfate RIL processing flowsheet that forms the basis of the plant upgrade currently being constructed at Barrick’s Goldstrike autoclave facility.

Jan 1, 2014

By J. Olaf Sund

"The New Brunswick gypsum and an-hydrite deposits make up part of the Windsor group in the Upper Mississippian. The present deposits were formed by surface hydration of the underlying anhydrite beds. The sub-hydrate, hydrate, and di-hydrate stages of gypsum are formed from the anhydrite by this hydration. The anhydrite was precipitated from sea water in embayments that were separated from the sea by a reef or bay-mouth bar. The anhydrite is the original form of the calcium sulphate precipitate.One gypsum deposit near Plaster Rock in northern New Brunswick was precipitated from sea water directly as gypsum, which is its present form."

Jan 1, 1960