Search Documents

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By F. C. Lendrum

Introduction The property of Normetal Mining Corporation is in Desmeloizes township, Quebec, twelve miles north of Dupuy on the main line of the Canadian National railway from Quebec city co Cochrane, Ontario. The ore bodies occur within a band of highly sheared and sericitized agglomerate which strikes N.60°W. and clips 82° north. Along a zone 1,000 feet or more in length and of variable width, the agglomerate has been replaced by copper, zinc, and iron sulphides, with copper usually predominant on the hanging-wall side and pyrite replaced in part by sphalerite on the footwall. A northsouth diabase dyke cuts through the ore zone near its east end. The Normetal mill produces a copper concentrate and a zinc concentrate which are shipped, respectively, to Noranda, Que., and Newcastle, Penn., U.S.A., for further treatment. The present paper deals with the milling of ore from what is known as No. 3 orebody. This is a lenticular body of high-zinc ore lying co the east of the diabase dyke, along the line of strike of the main ore zone, which extends westward from the dyke. On its northern side, No. 3 orebody is in contact along most of its length with a narrow band of copper ore which is highly oxidized.

Jan 1, 1948

By D. E. G. Maschmeyer

The operation of the pilot plant for the S-C Copper Process during 1976 has provided the basic data for the design of a commercial-scale plant. This paper introduces the commercial aspects of the S-C Copper Process through the presentation of a process flow diagram, a schematic flow diagram and basic design parameters for 75,000 tonnes per year (tpy) copper rod production from chalcopyrite concentrate. Basic operating requirements are outlined and a preliminary estimate of operating and capital costs for a Western Canadian location are summarized. The results have been compared with a modern smelter/electrorefinery to highlight the advantages and disadvantages of these two alternatives and to show why the new S-C Copper Process technology should be of interest to the copper industry.

Jan 1, 1978

By Harry Perry

By 1980, the free world's need for economic sources of energy is expected to double. As a result, there will be a tremendous potential for all energy sources working together to supply the demand. For coal to continue its dominant role as a low-cost energy source, means must be found for it to meet the challenge of nuclear power and to overcome obstacles placed on its use by air and water pollution regulations. As the more limited reserves of gas and oil diminish, economic ways are also required for converting coal to synthetic liquid and gaseous fuels, and to chemicals, thus resulting in optimum utility of the most abundant low-cost fuel resource. The means for accomplishing these ends can only come about by a vigorous research and development program. Successful efforts by industry and government working together, both in America and abroad, will assure the continued use of coal to meet the world's energy demands. This paper discusses the emerging patterns of energy sources throughout the world and the role that research and development on coal will play in supplying future energy requirements.

Jan 1, 1967

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012

By Thomas Kilpatrick

The liability created by building this railway is the great financial problem before the people of British Columbia at the present time. In dealing with the subject, I propose to divide it into three periods: The Past - The Present - and The Future. The Past The primary objects in building the railway were to provide an independent and direct route for the Grand Trunk Pacific railway into the city of Vancouver, and to open the central and north-eastern portion of the province.. This vast territory, almost one-half the entire area of British Columbia, has great wealth in fruit, agricultural, and grazing lands; timber, coal, water-power and minerals of all kinds, including some of the richest placer deposits in the world. Rivers and lakes teem with fish. Big game, including moose, elk, caribou, deer, grizzly and black bear, mountain goat and sheep, is plentiful and there is an abundance of small game and fur-bearing animals. In addition, its scenic attractions are unsurpassed in Canada. To develop these resources it was considered necessary to build a railway from south to north as a main artery of transportation and, if necessary, branch lines to carry heavy .shipments of coal or other commodities. Lighter freight may be handled by motor trucks from distant points to the railway.

Jan 1, 1925

By R R. Wainwright

Friction-type hoists have been in operation at Geco Mines Limited since Septtember, 1957. At the end of the year 1963, the skip hoist had handled nearly ~ million tons of ore and waste. In March, 1962, with the deepening of the shaft, the hoisting de11th was increased from 1,450 to 2,450 feet. Operating experience with the hoists, hoist and balance ropes, rope treads and other related equipment is presented. The paper is intended to supplement an earlier one -"Heavy-Duty Friction Hoisting at Geco Mines," by W. M. Harvey (C.I.M. Transactions, Volume LXIII, 1960, pp. 193 -197). General G ECO Mine Limited is located at Manitouwadge, Ontario, approximately 160 miles east of Port Arthur and 190 mile northwest of Sault Ste. Marie. The Company was formed to exploit a copper-zinc-silver orebody, with current ore reserve (1963) of approximately 21 million tons. The production plant was designed to mine and treat 1.25 million tons per annum. The production and service hoists are mounted at-the top of a reinforced concrete tower above the shaft.

Jan 1, 1965

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By Elaine R. Goetz

The eastern and southeastern regions of Ohio are part of Appalachian coal country, with a documented 1,300 miles of streams impacted by acid mine drainage. Since 1995, partnerships of local watershed groups, government agencies, private industries and universities have focused on the remediation of the affected waterways. The partnerships have spent $2.4 million annually in constructing and operating treatment systems such as wetlands, anoxic limestone drains, successive alkalinity production systems, steel slag leach beds, and lime dosers. These systems have been partially successful, and water quality has improved in the region, but no treatment has yet met the ultimate objectives of low cost, continual remediation. Our research group has investigated an alternative system for acid mine drainage treatment: electrolysis combined with pH adjustment to selectively precipitate recoverable, saleable metal products to offset the cost of treatment. We utilized a $0.2 million pilot facility constructed by the Wayne National Forest, in Nelsonville, Ohio, to process approximately 40 L/min of mine drainage from surrounding seeps. The pilot facility has multipurpose tanks that can be adapted to process acid mine drainage with different characteristics, such as high or low aluminum content or high or low carbonate concentrations. Sodium hydroxide was used for pH adjustment. Results indicate that saleable product can be generated with this treatment technology. In an initial, not optimized trial, one seep yielded 4.7 kg of dried 69 % iron oxide product from 10 hours of pilot facility operation, treating 23,000 L with electricity costs of $4.68. Dissolved iron concentrations in the water were reduced from 242 ± 18 mg/L to 2.8 ± 2.0 mg/L (99.0 % removal) while the initial acidity of 443 mg/L as CaCO3 was neutralized to an alkalinity of 160 mg/L as CaCO3. Iron oxide can be sold as pigment for an average of $1.47 per kg in the United States. Currently, approximately 80 % of all pigment used in the United States is imported, and there is incentive to purchase domestically recovered pigment. If the iron oxide from the pilot facility could be sold as pigment for $1.47 per kg, 43 % of the operating cost (raw materials, electricity and construction costs) of treatment could be offset by the sale of the product. Considering the cost offset, the electrolysis process shows potential as a sustainable low cost alternative for treating acid mine drainage.

Aug 1, 2013

By H. E. Grier, H. H. Aronson, H. F. Coffer

"Nuclear explosions are currently being planned for use in oil and gas production, the recovery of oil from oil shale, gas storage and copper leaching. The current status of each of these projects is discussed, with emphasis on the economics of each application. The first commercial application of nuclear explosives will be in gas stimulation. Project Gasbuggy will be rapidly followed by two additional shots, also related to gas production. These three events, each in a different formation, will be described in this paper with a discussion on their significance to the world's oil and gas industry. The use of nuclear explosives in oil and gas stimulation should be a standard accepted practice within a few years. Calculations based on explosions in media such as tuff, alluvium, granite and dolomite predict large increases in productivity when nuclear devices are used in tight, thick formations. The broken-up rock resulting from the explosion becomes the new well bore, with a production rate of six to twelve times that of a normally completed well.Also included in the paper is a discussion of the real or possible problems associated with nuclear explosive engineering. The only major foreseeable problem is the seismic shock wave. This limits the size of explosive which can be used near important surface structures. A discussion is included on the radiation problem, which we believe to be largely psychological in the case of contained explosions."

Jan 1, 1968

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By D. E. Parson, W. A. Morgan

This paper offers a brief review of current literature pertaining to vacuum degassing or vacuum casting of steel as practiced in the U.S.A., Germany and the U.S.S.R. The advantages of vacuum degassing of large forging ingots, heavy section casting, for the conversion of rimming bessemer steels to killed steel and for the production of transformer steels are discussed. Operating pressures, reduction in gas contents and improvements in hydrogen segregation, steel cleanliness and mechanical properties, obtained with the various techniques, are described. The paper includes a description of an experimental vacuum stream-droplet degassing unit and some preliminary results obtained at the Physical Metallurgy Division Research Laboratories Department of Mines and Technical Surveys, Ottawa on laboratory steel melts. Experimental 500 lb direct arc, basic melts have been spray cast into either ingot moulds or dry sand moulds, held inside a vacuum tank. Also 500 lb melts have been

Jan 1, 1961

By P. E. Cavanagh

Introduction A comprehensive study of the economics of processes for smelting iron ores has been made by the Ontario Research Foundation on behalf of the Ontario Research Commission. This survey has included investigations of all processes in commercial use, and proposed processes which are still in the experimental stage. The two main objects of this work were to discover (l) whether any known processes would be particularly suited to present and future Canadian conditions, and (2) whether any new process would be of assistance in solving the present scrap shortage in Canada. The future prospects of the Canadian iron smelting industry have changed radically in the past ten years. For nearly twenty years before 1939 no iron ore was mined in Canada. The ore used was imported, mainly from the United States and Newfoundland. The economics of iron blast-furnace smelting always force the location of blast furnaces near the source of coal for making high-grade metallurgical coke, and near the market for iron and steel, rather than near the iron ore. Blast-furnace installations in Canada are confined to the north shores of the Great Lakes with ready access to United States coal and ore and the major Canadian markets, and to Nova Scotia near the coalfields of that Province. This distribution of primary smelting capacity naturally results in relatively high prices for iron and steel in the West, the North, and in Quebec.

Jan 1, 1948

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989