Search Documents

By R D. Lama, A Misra

One of the major factors restricting an increase in the productivity of a longwall mine is lower productivity obtained in a development panel. There has been a significant improvement in gate road development, particularly in mines requiring high density roof and rib bolting within 2 m of the face. Advance rates have increased from an average of 3 m to 5 m per shift in 1985 up to an average of 5 m to 10 m per shift in 1991. In mines at shallow depths with reasonably good conditions the increase has not been that significant. Advance rates have increased from an average of 7 m to 12 ni per shift in 1985 to an average of 12 m to 15 m per shift in 1991. Compared to the United States' (US) development rates, these are much lower. Extensive research work has been carried out to minimise cutting, wheeling, support setting time, and to optimise pillar length to achieve maximum advance rates. Pillar optimisation is very important in order to expedite adverse rates. This paper investigates various development rate technologies, both present and future, and optimises pillars to improve these dev elupment rates. Pillar optimisation is based upon time and motion studies conducted at mines in the Illawara region of New' South Wales, Australia, and the basic tools of arithmetic.

Jan 9, 1996

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By Edward A. McClatchie

A novel nondispersive electro-optical gas analyzer has been designed, fabricated and tested. The instrument is based on a pressure modulated absorption technique. Key features of this new gas analyzer technique include long-term zero and calibration stability. The technique was investigated for the gases carbon dioxide (CO2), carbon monoxide (CO), methane (CH4) and nitrogen dioxide (NO2). The delivered analyzer was capable of measuring the three species CO, CO2 and NO2. It is a compact (300 cu in) package, is battery powered and weighs 15 lbs. Some thirty readings of each gas may be made on a single battery charge.

Jan 1, 1980

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By R. K. Guthrie, H. B. Hill

"INTRODUCTION The Rodessa oil field in Marion and Cass Counties, Tex., Miller County, Ark., and Caddo Parish, La., was discovered in August 1930, when a well drilled to a depth of 5,506 feet in Caddo Parish, close to the surface trace of the Rodessa fault, produced gas in commercial quantities. During the next 5 years 21 gas wells were drilled, and a large reserve of natural gas was developed in the high part of the Rodessa structure underlying the Massive Anhydrite member of the Glen Rose formation.In July 1935 oil was discovered on the flank of the structure when a well drilled to 6,048 feet also in Caddo Parish, was completed as an oil well. The discovery of oil in the Rodessa structure initiated art intensive development program of more than usual interest to geologists, engineers, and operators in the petroleum and natural-gas industry. The complex nature of the different reservoirs, the large volume of ""free"" gas under high pressures and temperatures in the upper part of the reservoirs, and the high gas:oil ratios of some of the wells during the early production of oil presented many problems the solution of which taxed the ingenuity of those responsible for the development and exploitation of the Rodessa field.Early waste of gas and resultant dissipation of reservoir energy led to State intervention, which brought about effective regulation of the quantity of gas blown to the air. Oil production from wells producing more than 2.000 cubic feet of gas per barrel of oil was restricted, and oil allowables generally were based equally upon acreage and upon reservoir pressures. Consequently, oil-production statistics of the field are closely associated with gas:oil ratios and reservoir pressures.The primary object of this report is to present factual and statistical data on well performance in the Rodessa field and to show established trends under certain operating methods and practices in high-pressure gaseous reservoirs, which have been carefully developed and outlined by modern technique and exploited under close engineering supervision.The large size of the Rodessa field, it’s fairly well defined gas caps, and a somewhat definite water table in a part- of the oil- and gas-producing region are of special interest and importance in a study of the fluid and energy relationships in reservoirs. Consequently, the results of much of the authors' work in collecting and compiling date are presented in the form of tables, maps and cross sections to show the relative thicknesses of the different oil-and gas-producing members and their permeability and porosity relationships, and, when possible, the variations in stratigraphy are exhibited in cross sections. Results of a detailed analysis of cores from a number of wells also are presented in tabular and graphic form."

Aug 1, 1943

By L. C. IlsLey, J. W. Paul, E. J. Gleim

Flame safety lamps have been used in gaseous mines since the Davy lamp was introduced, more than 100 years ago. During the last decade the flame safety lamp has been rapidly replaced by the electric lamp as a device for illuminating the miner's working place; in the United States the electric cap lamp has been widely adopted. For example, in 1911 approximately 45,000 flame lamps and no electric lamps were being used in the Pennsylvania bituminous mines, which were then producing 35 per cent of all the soft coal mined in this country; by 1918 the flame lamps had decreased to 17,000, whereas electric lamps-mostly of one maketotaled nearly 48,000. In Great Britain during the same years the total of 723,934 flame lamps decreased to 590,185 and the electric lamps gained rapidly from 4,298 to 156,521. No later reliable figures are at hand. However, before the flame lamp becomes obsolete, it is fitting that the Bureau of Mines compile a permanent record of a device which has served the mining industry for more than three generations, and not only made possible the development of entire districts that otherwise could not have been worked but undoubtedly saved the lives of thousands of underground workers. Flame safety lamps are capable of doing more than the name indicates. First, under normal conditions, they can be used in a mine atmosphere that contains an explosive mixture of gas and air without great danger of exploding such a mixture, though such use of a flame lamp should not be permitted. Second, to an experienced man they indicate percentages of gas much lower than the explosive limit, and thus can be used to indicate to workers the approach of an unsafe condition in the mine atmosphere. Third, flame lamps will not burn in an atmosphere greatly deficient in oxygen, and they therefore warn the users of such deficiency in time to withdraw to a place of safety. Flame safety lamps are still used rather widely in the United States for general illumination and to a still greater extent for detecting gas. Many coal-producing States require fire bosses to use these lamps in gaseous mines, and the regulations of several States specify that a gIven number of such lamps be kept available for emergency service.

Jan 1, 1924

By B. H. Moore

The opportunity to evaluate the pile design procedures used on a major project is an infrequent occurrence. It is even more infrequent that the project involves piles with significant tension and horizontal capacities. This report synopsizes over twenty years of design and construction experience on just such a major pile founded structure. The philosophy governing foundation design procedures is described and discussed. The order and extent of full scale pile testing are evaluated. Principal points in the specifications are established and their effect on construction progress and claims are noted. The report concludes with recommendations for future projects.

Jan 1, 2010

By WILLARD W. CUTLER

This bulletin reviews, in the light of recent experience, the use of production-decline curves in estimating the future production of oil from wells. It deals with the estimation of the reserves of recoverable oil in properties already producing or in those adjacent to them, takes cognizance of the physical laws governing expulsion of oil from oil sands, and shows how the production-decline curve can be made to utilize these laws in estimating reserves and rates of production. The valuation of oil properties should be based on the total amount of oil recoverable from a property by the methods in use, the rate of recovery, the cost of production, and the selling price. Numerous other curves besides those for reserves and rates of production may be formed from the production-decline curve and will present desired information in a convenient time-saving form. These curves also are described. Methods developed before the production-decline curve method was used are briefly discussed in order that the principles on which estimations of oil reserves are based may be made plain. The construction of curves and tables for estimating future production of individual wells and of average wells in most of the important oil districts of the United States is described and operating problems that may be solved by the use of production-decline curves are discussed. The bulletin does not deal with costs, oil prices, or the methods of evaluating oil properties. Many engineers have amply demonstrated the value of the production- decline curve method by forecasting within reasonable limits the production of many thousands of wells and tracts. The value of similar estimates depends however, on (1) the application of trustworthy methods; (2) the care and judgment of the estimator; and (3) the length and reliability of the records and the accuracy of ofher information used in estimating future production. When adequate records and information are available, experience has shown that It qualified engineer can forecast production far more accurately than has been deemed possible, except where the usual conditions governing the expulsion of oil from a sand have been radically changed by applying compressed air or by flooding with water, or, to a less degree, by using vacuum. In general, the production-decline curve method, though there are limits to its accuracy, is far more trustworthy than any other.

Jan 1, 1924

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

By Patterson B. G

The small party of mining men who formed the original Mount Morgan Syndicate in 1882, commenced operations on the top of the mountain with what were practically nothing more than small hillside quarries, It was not until 1891 that underground stoping began, and open-cut mining therefore commenced with the commencement of operations. This hillside quarrying, however, seems to have been quite haphazard and unsystematic ; there is no trace or sign of any properly devised mining scheme. This can be seen plainly enough from an examination of old mine plans; for in less than five years after stoping was; adopted, the open-cut was down into the stoped-out ground. The following table, prepared from these old plans, shows the downward trend of the excavation in the past fiftyseven years:-

Jan 1, 1939

By R. R. Klimpel

"SYNOPSISA discussion of the importance of flotation rate in the analysis of mineral flotation is presented. In particular, the highly interactive nature of the flotation ""system"" is emphasized where there are components of chemistry, equipment, and operating conditions simultaneously involved. It is further shown that: 1) flotation rate must be measured in order to economically optimize the performance of an industrial flotation circuit, 2) that consistent patterns exist in both flotation rate and equilibrium recovery when changing various settings of the system components, 3) that knowledge of these patterns is necessary in order to avoid making system changes that are either self-compensating or dramatically re-enforcing in some particular aspect of performance, and 4) the rate related role of the chemistry component (e.g.frothers and collectors) is often much bigger than is sometimes realized (especially in a negative sense involving overdosing of reagents). INTRODUCTIONFroth flotation is widely usedl-6 in mineral beneficiation processes as a method for separating different types of finely divided solids present in a liquid (usually aqueous) suspension. The approach is based on the contacting of solids with upward moving air bubbles in an agitated vessel where the solids are exposed to chemicals (collectors) which create a condition favoring the attachment of a certain portion of the solids to the air bubbles. This selected portion is then removed in a froth stabilized by chemicals (frothers) and subsequently recovered from the flotation vessel. Depending on the settings of the various components of the flotation ""system"" (see Figure 1) it is possible to achieve a wide range of flotation performance."

Jan 1, 1984

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

By G. M. J. van Heerden, R. C. W. Webber-Youngman

"This article describes the re-engineering principles applied in the design of a personnel transportation system for the Bafokeng Rasimone Platinum Mine in the Rustenburg area of South Africa. It incorporates conveyor belt travelling, chairlift operation, and also includes consideration of proposed changes/modifications to the existing conveyor belt infrastructure.The purpose of the project was to identify, through a process of evaluation, the appropriate option and/or combination of transportation options that would be safe in terms of personnel transportation as well as cost-effective. Alternative measures for transporting personnel (not using belt riding) would have a significant positive spin-off, increasing the availability of the belt and thereby increasing production. This paper explores the feasibility of interventions that would improve safety through eliminating risk associated with personnel transportation as well as contributing towards improving the mine’s position on the cost curve.The design in consideration at the Bafokeng Rasimone Platinum Mine consists of two shaft systems, namely the North Shaft and South Shaft, each comprising twin decline shafts. One of the decline shafts is equipped with a conveyor belt for rock and personnel transportation, and the other with a winder for trackbound material transport. The conveyor belt has been used for personnel transportation since the commissioning of the shafts. The conveyor belt is equipped with platforms for personnel getting off and on the belt and a number of safety devices designed to ensure safety while travelling on the belt. Intensive training in the practical aspects of belt riding is given to every person, and unsupervised riding on the belt is permitted only once belt riding competence is demonstrated. Despite this, the safety results were poor, with 106 injuries between 2006 and May 2013. Fortunately, no fatalities were reported during this period.An investigation of alternative means for personnel transportation or engineered solutions to the current conveyor belt infrastructure in the safest, most effective, and most economical way was therefore needed. There was a major risk of safety-related stoppages being imposed following another belt accident/incident. This would prevent the mine from transporting personnel underground by belt and result in major production losses. From the commissioning of the Phase 2 shaft deepening project on both shafts, dedicated chairlifts have been used for personnel transportation as opposed to the conveyor belt installed in the Phase 1 area. The chairlifts have been in operation since 2004 and no chairlift-related incidents have been recorded thus far. According to safety statistics, it is clear that the chairlift is the safer method for the transportation of people in the shaft.To fulfil the objectives/scope of this study, it was recommended that both primary (new chairlift decline with infrastructure) and secondary options (modifications to the current conveyor belt infrastructure) be considered for implementation on both the North Shaft and South Shaft to reduce or eliminate accidents/incidents as a result of belt transportation. The associated capital expenditure would be approximately R200 million. Considering the future impact on the business as a whole, this would definitely be capital well spent."

Jan 1, 2016

By F. Habashi

Siberia, a vast country rich in mineral resources and a large number of different ethnic groups. To the east of Lake Baikal is Buryatia with capital Ulan Ude. The Buryat are closely related to the Mongolians. Ulan Ude is connected to Ulaan Baatar (Ulan Bator) the capital of Mongolia by train – a 26 hours trip. Getting a visa to Russia is not a simple case. Visits to metallurgical research laboratories, Lake Baikal, and historical museums are enriching experience.

Jan 1, 2006

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By AIME AIME

The first session, held Tuesday evening, February 23, in North Sheffield Hall, was called to order by Louis V. Pirsson, Chairman of the Local Committee, who introduced Prof. Russell H. Chittenden, Dean of the Sheffield Scientific School of Yale University. Professor Chittenden, in behalf of the Governing Board, felicitated the Institute on its visit to New Haven, and cordially welcomed the members and guests to the University and the city. Dr. James Douglas, who presided at the meeting, responded in behalf of the Institute. The Secretary announced that, upon the proposal of many members, the unanimous report of the Committee on Membership, and .the unanimous recommendation of the Council, the following members had been unanimously elected by the Board of Directors Honorary Members in the American Institute of Mining Engineers Prof. Richard Beck, of Freiberg, Saxony, in recognition of his distinguished service to technical literature, and the cordial

Apr 1, 1909