Search Documents

By Sayan Sarkar

HAMR (Hydrogen Assisted Magnesiothermic Reduction) process is a promising alternative route of titanium production, which is convenient due to reduction at relatively lower temperatures below 750 °C and usage of cost-efficient TiO2 as the starting material. A crucial step involved in this process requires the Mg reduction of TiO2 subjected to H2 atmosphere which produces porous TiH2 along with residual magnesium impurities. Before the final heat treatment and deoxygenation steps for consolidation of the Ti powder, leaching plays a significant role in the removal of Mg impurities. In this report, we present a systematic study on the role of acid concentration (HCl), temperature and the kinetics of MgO dissolution. In addition, we also report the controlling mechanism during kinetics of MgO dissolution in acid. This parametric study will provide a platform to ensure very low Mg content that meets with ASTM standards during production of Ti in the HAMR process.

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By A. Kiziltas, D. J. Gardner, C. W. Mcllwraith, J. W. Bridge, M. L. Peterson

"Dynamic mechanical thermal analysis (DMTA) tests were conducted on high-oil content, paraffin-based wax used in wax-coated granular composites. These composites make up the surface of synthetic Thoroughbred horse racetracks used in North America. The modulus and damping response from the DMTA tests were correlated with the dynamic triaxial shear strength response of the bulk track material taken at two different operational temperatures and at four strain rates. The purpose of these tests is to understand the mechanisms of shear strengthening of the bulk track material as the wax is heated through the first crystalline solid to liquid nominal transition temperature. Previous work using differential scanning calorimetry confirmed that under common operational surface temperatures, the wax coatings undergo distinct thermal transitions. The resulting increase in triaxial shear strength values affects the consistency of the racetrack which, in turn, can potentially affect Thoroughbred racing performance and safety of the track surface.IntroductionSynthetic granular composite materials are being used in nine Thoroughbred horse racetracks in the United States as well as in other tracks around the world. In one case, their use was mandated by the state of California in 2007 due to testimony that these tracks were significantly safer than traditional dirt tracks [1]. Several synthetic tracks have shown substantial reductions in injuries since switching to synthetics; one California track showed a 75% reduction in catastrophic horse injuries during the first year as compared to the previous year racing on a dirt track [2]. The composition of the tracks in the U.S. generally consist of silica sand (>70%), polymer fibers (<5%), and rubber particles (0-15%) all coated with a paraffin-based, high oil content wax [3, 4]. In a recent study of several synthetic racetracks, to include the track location in this study, the oil content ranged from 34 to over 44% by mass [5]."

Jan 1, 2011

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By Dai Yongnian

"The feasibility to vacuum distillation of a crude metal or an alloy was discussed. The equilibrium relationship between vapor phase and liquid phase in A-B system - - - - - PA/PB =BAa*/b has been derived. The separation coefficient, BA = rAPA/(rBPB) is a judgment criterion. By calculation PA/PB, the equilibrium composition diagram of vapor phase and liquid phase was drawn. By use of the equation derived by M. Olette, the relationship among the volatilization amounts of various impurities in a crude metal (yi) was further solved. 1-(X/100)= C =(1-Y1/100)1/02i . From yi value obtained in practice, 2i, Pi and then can be calcu-lated. The correct volatilization order of various impurities was obtained. These results can be applied to determine the practical conditions (temperture, vacuum degree, type of distilla¬tion furnace, times of distillation and control of product composition) in distillation of a crude metal or an alloy.INTRODUCTIONRefining and separation of various impurities from nonferrous crude metals by vacuum distillation have many the advantages of high metal recovery, impurities recovered in metallic state, flowsheet simplified, good enviromental protection, low operation costs and in complex equipment. So in recent years this method has been adopted widely.Vacuum distillation has also been studied and used in separation of various elements from non-ferrous alloys and the area of its application is being extended rapidly.At this situation, some problems have been put up: What kind of impurities can be removed from crude metals? What kind of alloys can be separated by vacuum distillation? In present paper, attemps have been made to answer these problems and combine with practical results to analyse some valuable data obtained from testwork on vacuum distillation of crude tin and Pb-Sn alloy."

Jan 1, 1988

By N. Solak

CrN, TiN and Ti-B-N coatings were deposited onto H13 hot-working tool steel and alumina substrates by arc-PVD. The coatings were characterized with respect to their mechanical and structural properties. Oxidation behavior of the coatings on alumina substrates was investigated by TG/DTA. Samples coated on H13 substrates were oxidized in a tube furnace under atmospheric conditions at specific temperatures determined from TG/DTA tests of the same coatings deposited on alumina substrates. The oxide scale morphology was characterized by scanning electron microscopy and X-ray diffraction. Oxide scale thickness change and TG data were used to calculate oxidation reaction activation energies. It was determined that boron addition into TiN coating improves not only mechanical properties but also oxidation resistance. Depending on the substrate material different oxidation activation energy values for the TiN and Ti-B-N coatings were determined revealing the importance of film morphology on oxidation resistance.

Jan 1, 2006

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By Alex Luyima, Jaan Kers, Lifeng Zhang

"The pyrolysis of PWBs was investigated by a TG-DTA-MS furnace at 300–1173 K. The kinetics and the control of emitted gas during the pyrolysis of PWBs with and without chemical additives were studied. Moreover, the possibility of controlling the amount of toxic exhaust gases like HBr, C6H6, Br2, Cl2, HCl gas and recovering beneficial gaseous fuels like CH4 and H2 from pyrolysis process is discussed. The MS data for each PWB sample were examined as a function of temperature and particular m/z values could be associated with the mass loss steps in the TG data. The degradation of the organic material was characterized by m/z = 2, 16, 18, 28, 36, 44, 71, 78, 81, and 160. Fe2O3 was the best inhibitor of toxic HBr and C6H6 when compared to Al2O3, CaO Y-zeolite and ZSM-5. Moreover, it had no significant effect on the valuable H2 and CH4 gas evolution. This selective inhibition of toxic gases while maintaining the valuable ones make Fe2O3 the best candidate among the investigated additives in controlling gas emissions from PWB pyrolysis process.IntroductionThe electronic and electric industry is one of the world’s largest and fastest growing manufacturing sectors. As a consequence of this growth, electrical and electronic waste (e-waste), such as computers, washing machines, printers, mobile phones, television sets, stereos, radios, etc., is generated in large quantities around the world. Printed wiring boards (PWBs) are a common component of many electronic and electric systems.[1]. The rapid development and expansion of the electronics industry over the past several decades have led to a dramatic increase in the production of PWBs and a corresponding increase in the amount of waste generated from both production and disposal. The environmental impacts of the treatment and recycling of PWBs waste have become a major concern [1-2]. PWBs are particularly problematic to recycle because of the heterogeneous mix of organic material, metals, and glass fiber [1]."

Jan 1, 2012

By Gavin K. W. Freeman

The efficient separation of cobalt from nickel is a fundamental objective in the refining of cobalt. Based on recent experience at the Corefco refinery in Fort Saskatchewan, the identification of a novel process for the selective precipitation of cobalt from aqueous ammonia leach liquors is described. The addition of calcium sulphate, CaSO4.2H2O (gypsum), to an aqueous solution containing cobalt(III) hexammine sulphate, [Co(NH3)6]2(SO4)3, will result in the precipitation of a sparingly soluble double salt having the stoichiometry, [Co(NH3)6]2(SO4)3.2CaSO4.xH2O, where x = 4 or 6. Leach residues, which may contain a significant quantity of cobalt associated with the cobalt calcium double salt, can be washed with process solutions that contain ammonium carbonate. After contact with ammonium carbonate, the cobalt is recovered into solution, while the calcium is re-precipitated as the insoluble carbonate. The simplicity of this elemental separation and its high selectivity for cobalt, as well as the demonstrated usefulness in improving cobalt recoveries, are the basis for the potential applications of this process.

Jan 1, 2003

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Huimin Lu, Lian Zhou, Panpan Wang

"For the low concentration C02 exhaust gas from coal-fired power plant, steel plant emission trapping and recycle problem, a pressure swing adsorption process was studied, using a porous imidazolate framework materials (ZIFs) as adsorbent, separating carbon dioxide from fuel gas mixture. In the carbon dioxide reduction condition by electrochemical method, using ionic liquids as electrolyte, the oxygen and carbon products could be obtained, including carbon nanotube, nano carbon fiber and amorphous carbon. At last, a new C02 collection, recycling and reuse technology was formed.IntroductionDuring the combustion of fossil fuel in coal-fired power plant or steel plant, large amount of carbon dioxide has continuously emitted into the atmosphere. The phenomenon has resulted in the melt of arctic glacier and the frequent emergence of abnormal climate. How to reduce the emission of carbon dioxide and protect human living environment has become a worldwide challenge. Recently, there are three routes to resolve this problem: The first one is to adjust the energy structure and develop new energy, such as solar, wind, hydrogen; the second one is to improve energy efficiency and avoid waste; the third one is to research capture and sequestration of carbon dioxide (CCS). But many researchers have come to realize that the recovery and utilization of carbon dioxide are more important than the sequestration of it. Because the captured carbon dioxide just buried under the earth maybe cause secondary pollution if carbon dioxide leak out from the adsorbent."

Jan 1, 2013

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or near it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Binxu Zhaug, Mark Jolly, Xiaojun Dai

"In conventional investment casting process of aluminium alloys for the application of the aerospace industry, to assure the quality of the final casting, usually the foundry uses large runner system which results in low yield, high energy consumption and high GHGs emission. In one case of this investigation, the yield is between 5 ~ 10% which means that the current casting process wastes large amount of energy and generates lots of scraps. By applying a new casting method, the bulky runner system and the melting/holding time are significantly reduced, the quality of the casting is improved, and in the meantime the related energy consumption and GHGs emission are significantly decreased. In the investigation, the energy efficiencies and GHGs emission between the current and traditional processes are calculated and compared.1. IntroductionAs one of the conventional casting process, Investment Casting Process (ICP) and its applications can be traced to thousand years ago [l]. In current casting industry, ICP still plays an important role in the production of small and precious castings with high quality requirements in automobile and aerospace industries. Both casting quality and manufacturing costs which mainly consist of energy costs have crucial effects on the competitiveness of castings in the market. In the production of aluminium alloy castings using ICP, the energy cost and energy efficiency of a casting facility depend mainly on the efficiency of its melting and heat treating performance. In association with the two performances, more than 60 % of the total process energy costs are symbolised in a typical casting facility [2]. Additionally, in conventional ICP of aluminium alloys for the application of the aerospace, to assure the quality of the final casting, typically the foundry uses huge runner system including big risers/feeders which cause low yield, creates lots of scraps and generates high energy consumption. Consequently, there are huge opportunities for casting industry to choose the best practices for potential energy saving. Furthermore, the reasons such as the stringent limitation of environmental legislation in Europe and the pressure of the rising energy price force the casting industry to reduce the energy consumption and greenhouse gases (GHGs) em1ss10n."

Jan 1, 2012