Search Documents

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By Xiang Sun

Microwave processing has been under continuous development as an advanced heating method in modern industries. However, problems with uneven heating still remain. Although heating uniformity is highly dependant on the properties of the materials being heated, proper furnace design to prevent uneven field distribution is another important factor. As an alternative to experimental measurements and adjustments to find appropriate furnace parameters, computer simulation is a convenient method for modeling, understanding, and improving the uniformity of microwave heating. This paper discusses current modeling technologies as well as applicable techniques for improving microwave heating uniformity. The purpose is to give a basic understanding on how to find, analyze, and minimize the problems associated with uneven heating in microwave processing.

Jan 1, 2006

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By H. Castillo

This paper describes the computer simulation of thermal stress fields generated in the quenching of the ns 415 H Steel automotive parts (Valve Lifters), running the ANSYS Multiphysics software of finite element (FEM). Simulation was performed introducing residual stress measurements on specific values areas, like internal pressure condition in the material. The stress condition effect in the material and the properties as temperature function data, were introduced to the FEM software. The thermal stress simulation was made on the 2D system. The parts were austenized to 850 900 °C and then oil quenched, tempered at 150 -200°C, and air cooled. The X-Ray diffraction technique was made to take measurements from residual stresses on valve lifters surfaces. The results analysis showed the ideal stress condition necessary in raw material to reduce the scrap percent in grind operations after hardening heat treating process. Keywords: Thermal Stresses, Temperature profile, Computer Simulation, Finite element analysis, Quenching of steel, Residual Stresses

Jan 1, 2003

By M. A. Cocquerel

External process energy requirements and air pollution control regulations formulated to limit particulate and SO2 emissions are impacting on smelting and converting technologies and the corresponding process and secondary gas handling systems. This paper presents an overview of the different technical solutions used for cooling and dedusting the process gases in the different pyrometallurgical copper concentrate stages, including: drying, smelting, converting, slag cleaning and fire refining. The main principles of the process gas handling systems are presented &d a qualitative technical and economical comparison is discussed in relation to process changes, energy recovery and marketing or disposing of the various sulfur fixation by-products. Finally, a brief review of the methods for fixing sulfur contained in the process and secondary gases is presented.

Jan 1, 1999

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012

By Anne Kvithydl

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both CO, and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na,C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO, and argon. However, less residue is formed when heated in CO,.

Jan 1, 2008

By Gordon Irons, Kevin Graham, Krishnakumar Krishnapisharody

Ladle or secondary metallurgy in steelmaking is an essential process step for the production of high-quality steel. Professor David Robertson was a pioneer in the modeling of these processes, in particular gas-metal fluid dynamic interactions and the rates of slag-metal reactions. This is now a highly active area of research, and some of the recent developments in this area will be reviewed.

Jan 1, 2014

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia's Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech's laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By Defeng Zhou, N. Trubaki, Jian Meng, Fanzhi Menga, Xiaojuan Liu, Yanjie Xia

"The microstructure and the electric conductivity of (Ce0.9Nd0.1)1 xMxO2 d (M=Mo, W) solid solutions were investigated. It has been found that their conductivity containing the grain (s gi ), the grain boundary (s gb) and the total conductivity (s t ) at 300°C- 700°C can be ranked as: (Ce 0. 9Nd 0. 1 ) 0.99 W 0.01 02- d (s gi = 0.065 S.cm·1, (s gb = 0.265 S.cm·1, s t = 0.039 S.cm-1) > (Ce0.9Nd0.1)0.99Mo0.01O2- d (s gi = 0.053 S.cm·1, s gb = 0.142 S.cm·1, s t = 0.029 S.cm-1) > Ce0.9Nd0.1 s 2- d (s gi 0.045 S.cm-1, s gb = 0.091 S.cm-1, s t = 0.018 S.cm-1) measured at 700°C. The highest conductivity is obtained in (Ceo.9Ndo.1)0.99W0.01O2 d. These results indicate that (Ceo.9Nd0.1)0.99W0.01O2- d is the most promising electrolyte materials of intermediate-temperature solid oxide fuel cells among (Ce0.9Nd0.1)1-xMxO2- d. IntroductionRare-earth (e.g. La3+, Nd3+, Gd3+ and Sm3l doped ceria-based ceramic materials have been acknowledged to be attractive electrolytes for solid oxide fuel cells operating below 600°C due to their high ionic conductivity [1, 2]. In order to improve ionic conductivity of these electrolytes further, in recent reports [3-6], some aids such as Mo03 [3] etc. in a limited amount can be used which causes extremely high conductivity. For example, Zhou et al. found that with MoO3 doping, the grain boundary conductivity of Nd3+ doped CeO2- d increased notably especially at lower temperatures due to the effect of severely undersized do pants [3]. It is well known that the size of W6+ (rw6+ = 0.60 Å) is close to Mo6+ (rMo6+ = 0.62A) because of lanthanide shrinkage. Thus, rare-earth doped ceria e.g. Nd3+ doped CeO2g with WO3 in a limited amount will be probably good and even better electrolytes. However, much less information is available about these materials. Therefore, in our paper, (Ce0.9Nd0.1)0.99 1-xMxO2- d (M=Mo, W) solid solutions have been prepared and characterized. Much higher conductive electrolytes are found in the series of (Ce0.9Nd0.1)0.99 M0.01O02- d particularly (Ce0.9Nd0.1)0.99W0.01O2- d"

Jan 1, 2012

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By Hsing Kuang Lin

Extraction of zinc from chloride solution with dibutyl butylphosphonate (DBBP) in Escaid 110 has been investigated. The distribution coefficient of zinc was found to be independent of equilibrium pH. This independence indicates that the mechanism of the extraction may be solvation. Slope analysis for the system of dilute zinc chloride solution reveals that two moles of DBBP react with one mole of zinc. A series of tests were conducted to bring DBBP to its full loading capacity and the analysis of the results confirms this stoichiometric factor of 2. Extraction isotherms were established by varying either the AIO ratio or the concentration of zinc in the aqueous feed. Both curves were found to be identical.

Jan 1, 1990

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

Today’s world relies upon advanced green technologies that are made of critical elements with unique properties. Examples include rare earth elements (REEs) that are critical in the manufacturing of wind turbines and electric/hybrid vehicle batteries, key components of a greener future that face supply uncertainty and near zero recycling. To tackle their supply challenges, activities have begun for urban mining from waste electrical and electronic equipment (WEEE) that contain considerable amount of REEs, but their current level of recycling is less than 1%. Current recycling practices use either pyrometallurgy, which is energy intensive, or hydrometallurgy that utilizes large volumes of acids and solvents and generates large volumes of hazardous waste. In this study, we developed a novel and sustainable process to recycle REEs from WEEE, NiMH batteries in particular. The developed process relies on supercritical fluid extraction (SCFE) utilizing CO2 as the solvent, which is abundant, safe, cost effective, and inert. The effect of seven operating parameters, namely temperature, pressure, residence time, sample to chelating agent ratio, agitation rate, complex formulation, and methanol addition on REE extraction efficiency was investigated, and optimum operating conditions were determined. This work is the first to utilize a very efficient and safe process that runs at low temperature to extract metals from postconsumer products with minimum hazardous waste generation, while offering about 90% leaching efficiency for REEs. We expect our process to find widespread applicability in urban mining of REEs using green chemistry.

By J. W. Tsai

Both diamond crystals and diamond films were grown on silicon and copper substrates using a methane/hydrogen gas mixture as a precursor with thermal CVD techniques at low pressure environment. In addition to diamond particles, other crystalline phases including graphite and aluminum silicon carbide were observed on the substrate surface. ?The grown materials were analyzed with X-ray diffraction, electron microscopy, Auger electron spectroscopy and optical microscopy. Most synthesized diamond crystals were twinned. The flow rate of reactant gases, substrate nature, substrate temperature, decomposition temperature of the precursors, total pressure of reaction chamber, methane/hydrogen ratios and other possible parameters were varied during the growth processes, and the significant effects of these factors on nucleation and growth rate were evaluated.

Jan 1, 1989

By J. Markussen

The Falconbridge Matte Leach Plant was based on leaching Ni-Cu matte with strong hydrochloric acid in rubber lined equipment. It operated from 1968 to 1983 as a precursor to Nikkelverk's present C12 Leach. The process comprised two S.X. systems. NiC12.4H20 crystallization, crystal drying, NiC12.H20 pyrohydrolysis and HC1 gas recovery. The naphtha fired fluid bed pyrohydrolyzer produced granular NiO, subsequently reduced with H2 to granular nickel for sale. The development and operation of the pyrohydrolyzer are described

Jan 1, 1991

By Shuqiang Guo, Gonghui Yang, Xingxing Zhang, Yuyang Bian, Song Chen, Weizhong Ding, Yinhe Liu, Lan Jiang

One of the most promising refractory materials for application is zirconia in melting superalloy. In this work, the properties and phase composition of magnesia partially stabilized zirconia ceramics (MgO-PSZ) under different sintering temperatures were systematically investigated. Commercial magnesia partially stabilized zirconia (MgO-PSZ) powders were selected as the starting materials. The magnesia partially stabilized zirconia phase composition was measured by X-ray diffraction (XRD), the density of sintered samples was tested by vacuum density instrument, the thermal expansion were obtained by thermal dilatometer from ambient temperature up to 1450°C, and the microstructures of MgO-PSZ were characterised by scanning electron microscope (SEM). The results indicated that the properties of thermal expansion, densification, microstructures and phase composition were significantly affected by sintering temperature. Densification was consistent with SEM micrographs of MgO-PSZ at different sintering temperatures.

Jan 1, 2015

By Marisa Di Sabatino, Michael Phan Knudson, Mari Juel, Eivind Øvrelid

"A p-type Czochralski silicon ingot doped with boron was characterized for resistivity, minority carrier lifetime, interstitial oxygen, and metallic impurities. Analyses show a peak in resistivity and a dip in lifetime both occur 5 cm from the top of the ingot crown. This peak in resistivity deviates from the expected trend based on Scheil's equation for boron distribution. High concentration of interstitial oxygen in this area suggests that other oxygen-related defects, such as thermal donors and precipitates, may also be present here, and the observed peak in resistivity and dip in lifetime could be attributed to such defects. The low lifetime of 15-30 µs at minority carrier density of 7.5 x 1014 cm-3 is likely due to copper contamination.IntroductionSolar energy resources vastly exceed all other alternative energy resources, ensuring that solar power must play a crucial role in the evolving energy market. The economic viability of solar power in competition with other energy resources depends upon finding efficient, cost-effective, reliable, and controlled methods for solar cell production. In this regard, minimizing waste (such as material with unsuitable electrical properties that hinder solar cell performance) is a vital component of making solar cell manufacturing cost-effective. Impurities affect electrical properties of solar cell silicon in different ways (i.e. [1, 2, 3, 4, 5, 6]). In this work we focus on the role of oxygen and metallic impurities. Understanding oxygen impurities in silicon is critical to solar cell development because oxygen has been attributed with influencing critical electrical properties including resistivity and minority carrier lifetime and thereby potentially hindering solar cell performance or rendering material unsuitable for solar cells.[1, 2] Furthermore, oxygen is a common impurity in the standard type of solar cell silicon, Czochralski (CZ) silicon, due to diffusion of oxygen from the silica crucible into the melt during crystallization. [7] This study investigates the effects oxygen impurities have on the electrical properties of p-type CZ silicon."

Jan 1, 2013

By Upali Siriwardane, Tushar V. Kudale, Naidu V. Seetala

"Cellulose acetate (CA) membranes with 25% triethyl citrate (TEC) as plasticizer were prepared with varying thickness for CO2 gas separation from water-gas-shift (WGS) reaction products. The AFM analysis of the CA membrane showed that the uniform coating had fewer and smaller pores as the film thickness increased, and corroborated by gas permeability studies. The CO2 permeability has decreased faster than CO permeability with the CA/TEC membrane thickness, and findings support that the CA membrane could be used to entrap CO2. Several CA/TEC membranes were also staked to increase the separation efficiency. Positron Annihilation Lifetime Spectroscopy (PALS) was used to estimate the nano-porosity (pore size and concentration) changes of CA/TEC films. PALS results show a decrease in pore size with increasing CA-TEC concentration in acetone, while the pore concentration increases. The PALS results are correlated with the CO2/CO permeability variations as the CA-TEC concentration change.IntroductionHydrogen is one of the main energy sources available for the future advancement of clean fuel technologies especially for fuel cells. Generation of hydrogen and CO2 from Water Gas Shift (WGS) reaction mixtures of CO and H2O is of interest to many researchers since it allows a large scale production of hydrogen [1, 2]. Once hydrogen is produced using the WGS reaction, the output products contain mixture of CO, CO2, H2, and water vapor. Metallic membranes have been used as hydrogen separation membranes [3-6]. As H2 is separated from the mixture using the metal membranes, we need to separate CO2, and find ways of sequestration of CO2 to avoid environmental problems by greenhouse gasses. Polymeric Membranes have been used for CO2 separation [7]. Plasticizer can control the micro-structural properties such as pore size and concentration of polymer membranes [8], which influence the size/molecular weight dependent diffusion rates of the gas molecules. We have used cellulose acetate with triethyl citrate as plasticizer to separate CO2 from the WGS reaction products. Positron annihilation lifetime spectroscopy (PALS) is very sensitive and able to identify different kinds of defects and their agglomerates such as vacancies, vacancy loops, and voids [9, 10]. PALS has been successful in determining the free volume in polymers that influence the properties of the polymers [11, 12]. Microscopic properties of the free volume obtained from PALS have been correlated to macroscopic properties [13, 14]. We used PALS to study the nanoporosity (pore size and concentration) and fractional free volume changes of CA/TEC films, and used to understand the variations observed in the CO2/CO permeability as the CA-TEC concentration in the membranes change."

Jan 1, 2014