Search Documents

"This study examines the problems faced by open pit mine superintendents who make choices about how to direct their materials, either to the waste dump or to the mill. The paper explores the effects of introducing a 10% sampling error and a 0.9-times to 1.1-times sampling bias on positively skewed distributions for precious and base metals, negatively skewed distributions in the case of bulk commodities, and normal distributions as is the case for coal deposits. Parent distributions for each commodity were created on a 25 x 25 m grid using transformations of gold, iron ore, and coal data-sets, spatially based on a nonconditional Gaussian simulation. Ordinary kriging of grades for the three commodities into a 10 x 10 m grid provided the reference case against which the distributions with the sampling error and sampling bias for the commodities were compared. Imposing cut-off grades on the actual-versus-estimated scatterplots of the three commodities allowed the distributions to be classified into components of waste, dilution, ore, and lost ore. Ordinary kriging of values for each deposit type acted as the reference data-set against which the effects and influence of 10% sampling error and 0.9-times to 1.1-times sampling bias are measured in each deposit type. Indications are that the influence of error and bias is not as significant in gold deposits as it is in iron ore and coal deposits, where the introduction of small amounts of error and bias can severely affect the deposit value.IntroductionThe effects of poor sampling and the financial implications for mining companies, traders in mineral assets, and sellers of metal as dore or commodities is documented in a number of studies, the most notable of which is that by Carasco (2004). He examined the financial impact of poor sampling practices in the Chilean copper industry and found that finacial losses due to poor sampling amounted to hundreds of millions of dollars over the life of a mining operation. Holmes (2004) examined the effects of correct sampling and measurement as the foundations of metallurgical balances, and found that revenues from the sales of large iron ore shipments may be profoundly affected by poor sampling practices. In South Africa the way in which sampling of in situ gold-bearing reefs affects the mine call factor has been an ongoing study since the disparity between the estimation of gold in the reef and the actual gold bullion produced was noted by early investigators such as Beringer (1938), Jackson (1946), Sichel (1947), Harrison (1952), and a number of others."

Jan 1, 2017

By B. K. Loveday

There are certain ores that can be treated without upgrading (e.g., gold and uranium ores), and upgrading needs to be considered only for fairly low-grade ores of this type. If the grade is very low, treatment will not be economic even with upgrading, and there is therefore a limited range of ore grades for which upgrading is suitable.

Jan 1, 1980

By D. I. Nicol

An assessment is made of the possible scope for the use of activated charcoal as the solid adsorbent in an upflow fluidized-bed contactor, and a pilot-plant programme for the recovery of low concentrations of dissolved gold in this contactor is described. It was found possible to produce an effluent that contains less than 0,01 p.p.m. of dissolved gold.

Jan 1, 1997

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By Peter Stacey

This presentation provides comments on the increasing challenges associated with pit slope designs from the perspective of a design reviewer. Besides the technical issues related to the significant increase in current and proposed slope heights since the primary methodology in current use for pit slope designs was developed, other factors are coming into play. These include changes in mining equipment and associated operating practices, as well as a growing awareness on the part of mining executives and other stakeholders of the significance of stable, or at least well-managed, slopes. In the latter area, the associated clarification of responsibility has led to the increased use of either in-house or independent review consultants working on the behalf of management. From a technical perspective, since the mid-1970?s there have been significant improvements in the tools, particularly analytical methods, that are available to slope designers. There is also an increased understanding of the importance of a detailed geological model, with strong emphasis on alteration and/or structure to form the platform for the slope designs. However, the basic technology for determining the rock strength aspects has changed little, although an expanding body of experience is being accumulated in its use and there is a reasonable degree of comfort in its application for slope heights of up to at least 500 m. In addition, slope management is now viewed as a critical part of the implementation of slope designs and this has been supported by continuing improvements in slope monitoring systems. In recent years safety has become a primary concern, in part as a result of some major slope failures that have attracted the attention of regulators and the public, as well as mining executives, who are being held more responsible for unsafe conditions and associated events. There is therefore a growing demand for risk assessments to replace the deterministic design approaches upon which the current design technology is largely based. The focus of mine executives on safety has undoubtedly in part facilitated the recent long overdue revitalization of research into the design and stability of large pit slopes, the requirement for which has been recognized for many years by practitioners. This research, as well as the CSIRO Large Open Pit Study, will almost certainly provide advances beyond the empirical strength determination methods such as the Hoek-Brown failure criterion, which form the basis for current rockmass strength determination. At the same time, as mentioned above, there is a growing awareness of the requirement for a detailed structural model as a major component of every large slope design. In addition, other areas requiring further research include the impact of groundwater pressures on rock mass strength, particularly in rocks with low permeabilities, and the role of stress in high open pit slopes. From the perspective of design implementation, even with the recent significant advances in metal prices, mine operators remain under pressure to minimize mining costs. To address these constraints, mining equipment of ever increasing size is being introduced. There are, however, some disadvantages to this trend in the area of slope design. For example, the large electric shovels are not well designed for scaling bench faces, nor are they cost effective in this mode. As a result, specialized equipment may be needed in the mining cycle to perform the clean-up duties, which in turn increases operating costs. Further, where the large equipment is used in minimum width pushbacks to reduce the instantaneous stripping ratio, the advance rates can be high, but at the same time the associated changes in operating procedures are often not conducive to the concurrent use of such measures as controlled blasting, careful scaling and drain hole installation that generally improve stability. The resulting conflicts which may arise between the interests of production and those of slope stability are often exacerbated by the fact that these stabilization techniques actually increase the operating costs on which the operations manager is frequently judged, even though there is an overall increase in profit. Meeting the objective of developing slope designs which are practicable , i.e., achievable in terms of every aspect of the operating constraints in the specific pit, requires interaction and compromise between the geotechnical engineer, mine planners and operating staff during the formulation of the design criteria. In the current environment, it is often no longer sufficient to present slope designs in deterministic terms to a mine planner who accepts them almost without question. Increasingly, the requirement is that they be proposed within the framework of risk levels, related both to safety and to economic outcomes, to a decision maker who may not be a technical expert in the mining field. In this context, the mine executives must have sufficient information and understanding to be able to establish acceptable levels of risk for the company and other stakeholders; in this process the slope designers must play a major role. These changing requirements for presentation of slope designs necessitate clear communication of the basis for the design, which may be very complex, so that the implications of the designs may be thoroughly understood by all concerned. To ensure clarity at this stage, the slope designer must not only quantify the uncertainty in the input parameters, including the geological model, but must also be able to communicate and defend the resulting design recommendations. Where particular designs may have high associated risks, simply because of the degree of uncertainty in the data, this must also be recognized and proposed methods of reducing the uncertainty included in the presentation. In summary, from a reviewer?s perspective slope designs must not only be technically sound, but must also address the broader context of the mining operation as a whole, taking into account such factors as safety aspects, the available equipment to implement the designs, and the acceptable risk levels for the company. In addition, the designs must be presented in a way that will allow the mine executives, who are ultimately responsible, and the operators, who implement the designs, to fully understand the basis and short-comings of the designs and the risks associated with deviation from any constraints defined by the designer. It goes without saying that there must also be a well-defined monitoring system to confirm stability and detect and manage any variations in the design model or unexpected instability.

Jan 1, 2006

By K. O. R. Gebhard

Direct reduction-are we moving in the right direction? by K. o. R. GEBHARD INTRODUCTION Numerous forecasts predict a rapid growth rate for direct-reduction processes. The figures quoted are so impressive that many a top manager must fear that he will fall behind in technical development if he does not base a substantial part of his future steelmaking for mass production on direct reduction.

Jan 2, 1974

By G. E. Blight

Rates of erosion have been measured for the slopes and top surfaces of a number of gold-tailings dams in the Germiston-Johannesburg-Roodepoort area of the Transvaal. Preliminary results were given in an earlier paper. The present paper gives results for a four-year period of observation, and identifies the major factors affecting the rates of erosion from the surfaces of gold-tailings dams.

Jan 1, 1989

By A. L. Hinde, A. A. Bradley, P. J. Lloyd

The results of slow crushing tests in a stiff testing machine for both small and large step reductions of particle size are given. The energy consumption required to produce a given weight of minus 74 um material was determined when both single-crystal quartz and Witwatersrand reef were crushed. For comparison the two materials tested were also comminuted in a ball mill under optimum conditions. There are indications that slow crushing under stiff conditions is the most efficient method of breakage that can be devised. The comparison with ball milling results thus yields a value for the efficiency of ball milling of approximately 80 per cent. These results confirm that the best current estimates of milling efficiency, which are based on the free boundary surface energy of the material being milled, are probably too low by at least one order of magnitude.

By A. J. Buchan

The wear of steel pipelines used for the transportation of backfill slurries is frequently regarded as an erosion problem only. An investigation was undertaken of the likely contribution to the total 'wear rate' made by corrosion. Use was made of a pipe flow loop with catholically protected specimens and corrosion inhibitors. Laboratory electrochemical tests utilizing a rotating-cylinder electrode were also conducted. The slurries used were classified tailings from two mines at a relative density of 1,7. The velocities were between 2 and 4,9 m/s. Substantial decreases in the wear rate of up to 80 per cent for one slurry and up to 67 per cent for the other were obtained with the use of corrosion control, showing that corrosion and, more importantly, interaction between erosion and corrosion, contribute a significant portion of the overall wear in steel pipelines

Jan 1, 1994

By G. Y. Nisbet

The contribution made to the economy of South Africa by the-minerals industry is discussed according to four of its aspects. Firstly, the industry supports both students and lecturers in technical and academic institutions. This support covers virtually the whole range of courses available at the universities and technikons, although most is obviously devoted to the engineering and science faculties. Secondly, the industry makes a direct financial contribution to the State in that it contributes about40 per cent of the State's receipts from direct tax paid on incomes and 30 per cent of the contributions to the total State revenue. It provides employment for 28 per cent of the total active labour force, and contributes 24 per cent directly to the gross domestic product. Thirdly, the industry is responsible for over 65 per cent of the country's foreign earnings in spite of the significant rise in exports from the manufacturing sector. South African minerals are of crucial importance to the word, since the country has the world's largest reserves of seven minerals and features very prominently in many others. Finally, the industry makes an indirect contribution, referred to as the multiplier effect. This is the ripple effect on the economy made by a large injection of momey by which that money acquires an added effective value. A study made of the total production of the mining industry in 1978, for instance, showed this multiplier to havea value of 1,5. Thus, if this effect is included, the industry's contribution to the gross domestic product is 44,S per cent. Similarly, the industry is responsible for the creation of jobs both within itself and in other industries, which could amount to 100000 for the period 1981 to 1935.

Jan 1, 1981

By M. W. John, I. D. Matthews

SYNOPSIS This paper describes the process adopted for the recovery of gold from a dump originating from clean-up operations at Durban Roodepoort Deep Gold Mine. The gold-bearing dump material was refractory in nature, not being amenable to cyanidation because of the high level of carbonaceous material present. The laboratory tests on the material involved particle-size and chemical analyses, a mineralogical examination of the material, preliminary tests, and optimization of the process for the treatment of the dump material. The preliminary tests included tests on roasting, flotation, pre-leaching, adsorbent-in-leach, and blinding. Of these options, carbon-in-leach showed the greatest potential. The rate of gold dissolution, the rate of gold adsorption by the carbonaceous material, and the ratio of carbon to pulp were then investigated. It was determined that the ratio of carbon to pulp necessary to yield a reasonable gold recovery resulted in a carbon loading that was not high enough for economic elution and regeneration. A process incorporating washing of the carbon with cold acid between adsorption cycles was tested, and reasonable gold recoveries and carbon loadings were obtained. Durban Roodepoort Deep Gold Mine piloted the conceptualized process and determined that it was economically feasible. Two Browns tanks on site were modified, and an acid-wash tank was installed. The capital outlay for the plant was recovered within some 3 months.

Jan 1, 1990

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By M. Splaine, C. E. Dohm, S. J. Browner

As the grade of the gold (head grade) in the ore supplied to a reduction plants falls, the efficiency of recovery of the metal drops. This is not simply due to a fixed grade lost in the residue, since the residue grade is itself a function of the head grade. A multi-disciplinary approach was used in the construction of a model to represent the relationship between head grade and recovery efficiency. The model is a physicochemical one based on (i) the reaction characteristics of cyanidation, (ii) the milled-ore selection characteristics of gravity concentration, and (iii) the nearly log normal distribution of gold grades and particle sizes in ore reserves. The model was used to set sound target levels for recovery efficiency for a given head grade at a given plant, against which the performances of the plant equipment can be judged for control purposes.

Jan 1, 1982

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By W. T. Ruhmer

Slimes-dam construction in the gold mines of the Anglo American Group by w. T. RUHMER. Pr.Eng.. B.Sc. Eng. (Met.) (Fellow) Current practices generally in accordance with the principles of design and operation of slimes dams within the Gold Mining Division of the Anglo American Corporation are described. Although many of the details given are either obvious or have been amply dealt with elsewhere, these have been included for the sake of completeness. The selection of suitable ground for the deposition of slimes, the initial design and construction of a slimes dam, and its consequent operation are presented in logical sequence. Emphasis is placed on the code of practice for the construction of slimes dams issued by the Chamber of Mines of South Africa, and draft regulations (Water Act of 1956) dealing with pollution. Operating costs are included, and possible future trends are discussed.

Jan 2, 1974

By H. A. D. Kirsten

The professions are subject to a wide range of changing conditions, and are as a result forced to become more competitive. Although there is a need for specialization under these circumstances, no formal recognition, definition, or control of specialists exists. Some of the professions have attempted, over extensive periods of time, to resolve the issues involved, and have met with varying degrees of success. It appeared from the replies to a questionnaire sent to over one-hundred-and- .fifty professionals, that both advanced education and experiential training, are considered to be necessary qualifications for specialization. The opinion as to whether it should be lift to the individual to cal himself a specialist, or whether recognition should be based on peer review, was divided The majority did not want the number of specialists to be controlled The response to the reservation of work for specialists was ambivalent.

Jan 1, 1995

It is perhaps somewhat unusual for a contributor to comment on the authors' reply to his critique. However, I should like to return to a specific comment made by the authors. Award to Bob Laburn The Federation of Societies of Professional Engineers (FSPE) is pleased to announce that the 1984 FSPE Award for Services to the Engineering Profession was presented to Dr R. J. (Bob) Laburn at a function held on 14th February, 1984.

Jan 1, 1984

By R. C. O’Ferrall, W. G. Goulding

This paper describes the performance of a Robbins 52R Boxhole Borer from its introduction into the mine in July 1975 until late in 1977. As indicated by the costs involved, the performance has increased considerably and is expected to be even better once further envisaged modifications have been made. The average cost for the first half of 1977 was R275 per metre bored as against an average of R628 for 1975.

Jan 1, 1978

By F. S. A. de Frey, F. C. Kruger

Personnel management has undergone a remarkable change over the course of the past ten years. Personnel departments have played an increasingly important role, which today requires highly trained people and cannot be adequately served by the lesser qualified officials of yesteryear. Changes in the mining industry that stem from the demand for skilled labour to keep pace with technological developments and the mechanization of mines today demand that emphasis should be placed on the maximum utilization of manpower. Maximum utilization of manpower calls for more scientific and effective methods of recruiting, selecting, training, and placing workers so as to offer them the best opportunities for development and promotion, which naturally ensure a minimum labour turnover and eliminate labour unrest. This can be achieved only if well-qualified and properly trained personnel administrators are prepared to accept the challenge and apply themselves purposefully by assisting line mangement with the attainment of the company's corporate objectives.

Jan 1, 1982

By J. Kitagawa

The principal objectives of a metallurgical test programme for a 'grass roots' mining project are twofold. The first requirement is to establish the metallurgical viability of the project by demonstrating that acceptable results can be obtained by processing of the ore. The second goal is to obtain essential supporting data to determine whether the project is economically feasible. This involves several functions, which include the establishment of a workable flowsheet, the obtaining of design criteria for the commercial plant, and the collection of the evidence necessary to convince management, and often a third-party expert, that the metallurgy predicted for the ore can be achieved in a full-scale operation. The latter task is facilitated if a coherent overall picture is presented considering the geology of the orebody, the mining plan, and the mineralogy and metallurgy of the ore. The purpose of this paper is to provide guidance in the establishment of a test programme to meet the above objectives.

Jan 1, 1978