Search Documents

By S. Stone

Because of problems encountered with conventional timber supports, a system of concrete sausageshaped support pillars was tested. The pillars are 3 m long, 0,6 m wide, and between 70 and 80 cm high (the height of the stoping width). They consist of bags filled with a grout of cement (slagment and sand in the ratio of I :2, and are installed in a staggered pattern 6 m apart on dip and 2 m apart on strike. These support packs have proved successful, and, although they cost more than the timber supports formerly used (R4,63 per cent are supported as against R2,26 for the conventional timber pack), their use is felt to be justified when account is taken of the costs of lost production and low productivity due to the bad hangingwall conditions that occurred with the conventional system.

Jan 1, 1978

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

By D. Marcotte, R. V. Dutaut

"In mineral resource evaluations, geostatistical methods known as global change of support allow prediction of the theoretical histogram and gradetonnage curves prior to interpolations or simulations of grades. Two methods commonly used by professionals to guide the choice of interpolation parameters and assess results are the discrete Gaussian model (DGM) and the indirect lognormal correction (IndLog). These models rely upon an estimate of the dispersion variance of the blocks, which is derived by numerical integration of the variogram model over a discretized block. Due to difficulties in obtaining well-formed traditional experimental variograms (especially in the presence of outliers and limited clustered data), many professionals prefer to use ‘normalized’ variograms such as correlogram (non-ergodic variogram), pairwise-relative, or variogram of the normal score transform. A series of simulations with different grade distributions and variogram models are used to assess the performances and robustness of the various variogram estimators with respect to the DGM and IndLog global change of support. Our results show that the traditional variogram, the correlogram, and normal score variogram have better performances, compared to pairwise, for both DGM and IndLog. Moreover, DGM provided better results than IndLog for the grade distributions that are not strictly lognormal. These findings provide valuable guides for geostatistics practitioners. IntroductionWhen reporting resource estimates,practitioners are required to follow generalstandards described in the NI43-101 (CIMguidelines), JORC, or SAMREC codes. One cangenerally recognize three main parts directlyrelated to the block model:•,Pre-processing: exploratory data analysis (EDA), domaining, capping, compositing, declustering, variography•,Processing: block size, neighbourhood, interpolation types (linear or nonlinear)•,Post-processing: classification, reporting.Pre-processing aims to simplify and strengthen the processing step. Ideally, domaining, capping. and compositing is aimed at defining a single homogenous population. During the processing phase, a common practice is to use a block size corresponding to the planned selective mining unit (SMU). In most precious metal deposits (gold, notably), the SMU size is frequently smaller than the recommended half data spacing (Journel and Huijbregts 1978), resulting in high estimation variance and either a high degree of smoothing if the regression slope is managed or a high degree of conditional bias if it is not. Most actual resource estimates are made using block sizes between one-quarter to one-sixth of the average data spacing, sometimes even smaller. In addition to the block size, the interpolation choices for the neighbourhood selection and interpolator (e.g. inverse distance (ID) or ordinary kriging) are often based on the Qualified Person’s (the QP) experience and some basic validation plots that often do not consider the conditional bias (e.g. trends or SWATHs plots, which are designed to compare two sets of population using a one-dimensional graph)."

Jan 1, 2018

By Andrew Jones

This paper discusses the worldwide market and cost environments for the bulk ferroalloys namely manganese alloys (ferromanganese, silicomanganese), ferrosilicon and ferrochrome (high-carbon ferrochrome, charge chrome). Annual average market prices since 1993 are presented graphically and analysed, and the main supply and demand trends for manganese, ferrosilicon and ferrochrome are summarized. The paper shows carbon and stainless steel output data for 1995, 2000 and 2005, mainly to demonstrate the rising importance of China as a ferroalloys market. Developments in ferroalloys capacity worldwide from 1991 to 2007 are discussed (plant start-ups and closures, ownership changes). Finally, the paper examines developments in the main cost factors for the bulk ferroalloys, i.e., chrome and manganese ore, electricity, carbon reductants and labour. Note that data for 2006 are estimated based on information available in November 2006.

Jan 1, 2007

INFACON conjures up many things for many people. For the fortunate few who have been actively involved with this event since its inception, it brings back memories of far places, stimulating debates and above all, the people who have over the years contributed to the outstanding success of the Congress and who have added to the wealth of knowledge on all aspects of ferroalloys. The International Ferroalloy Congress (INFACON) has been held every three years since 1974. INFACON X will be held in Cape Town in February 2004. Simple arithmetic shows that next year?s Congress should in fact be INFACON XI. Thus, one Congress was skipped. INFACON 74, as the name implies, was held in 1974, in Johannesburg, South Africa. The event was sponsored by the Ferro Alloy Producers? Association of South Africa (FAPA), the National Institute for Metallurgy (NIM - Mintek as it is known today) and the South African Institute of Mining and Metallurgy (SAIMM). You will see some of the same sponsors involved in INFACON X. Dr. Robbie Robinson, renowned academic and past president of the SAIMM, was the Chairman of the Organising Committee. The editor was Dr. Helen Glen. Anyone fortunate enough to possess a copy of the proceedings of this first Congress will agree that from a literary and technical perspective, it is still the benchmark for subsequent events. A unique feature of INFACON 74 was the use of rapporteurs (my first duty) to ensure that the discussions following the presentations were recorded (in direct speech) as accurately as possible. This involved time-consuming correspondence (can you imagine life before e-mail?) to all parts of the world between the author and the person posing the question, with the rapporteurs acting as go-betweens. It is understandable that the much-awaited proceedings only saw the light in 1975. The names recorded in the proceedings as the members of all six committees read like the who?s-who of the South African ferroalloy industry at the time: Dr. Peter Jochens, Mr. Harvey Reid, Mr. Piet Streicher, Prof David Howat, Mr. Sigurd Selmer-Olsen - to name but a few. The Congress was held in the new, very fashionable and upmarket Carlton Hotel in the CBD. In the Foreword of the proceedings, Dr. Robinson provides an insight into the event. Three hundred and thirty six delegates from twenty two countries attended the Congress, which was opened by the Honourable P.G.J. Koornhof, Minister of Mines. Again, the opening address makes fascinating reading. During the Congress an ad hoc committee was convened as the first International Committee on the Organisation of Ferroalloys Congresses, with representation from the main ferroalloy associations of the world. The following decisions were recorded: ? The Congress would be continued at three-yearly intervals under the name of INFACON ? Every third Congress would be held in South Africa ? NIM (Mintek) would provide the permanent secretariat. Six technical sessions were held, each preceded by a plenary address with a closing address by the session chairman. In all, thirty technical papers were presented. Prior to the closing address, a panel discussion on factors affecting the future of the ferrochromium industry provided stimulating debate in the form of a question-and-answer session. The hosting country for the next INFACON would be announced. Eventually, word got round that the next INFACON would be held in Japan. However, due to unforeseen circumstances, the event was cancelled ? thus no INFACON 77. INFACON 80 was subsequently held in Lausanne, Switzerland from 12th to 16th October 1980. The event was organised by IFPEO, Institut des Producteurs de Ferro-Alliages d?Europe Occidentale. The Congress was officially opened by the President of IPFEO, Mr. R. Björklund, who was also President of the Organising Committee. The technical sessions were held in the Palais de Beaulieu. The Congress was well attended by 400 participants from 28 countries as well as 100 accompanying ladies. A total of four plenary addresses and 18 technical papers were presented. As with the first event, an international panel discussion (questions and answers) preceded the closing address. In his closing address, Dr. Louw Alberts, Chairman of the International Committee on Ferroalloys and President of NIM, presented an insight into the factors affecting growth in the industry and where growth was likely to take place. Twelve exhibitors had stands at the Congress. Attendees could choose from four post-event tours to Belguim/France (SADACEM/Compagnie Universelle d?Acetylene et d?Electro-Metallurgie), France (CUAEM), Finland (Outokumpu Oy) and Norway (Elkem Fiskaa plant).

Jan 1, 2004

By J. M. Sabio, A. W. Stalberg

Keywords: Pyrometallurgy, furnace, calcium carbide, acetylene, Newcastle The manufacture of calcium carbide in Newcastle, South Africa, was started in the late 1950s by a company called South African Carbide, at the Ballengeich site. In 1978, this operation was bought by the forerunner to the present AECI Ltd, a large producer of commodity chemicals at the time. Production continued at this site until 1992. In the meantime, Karbochem, an operating division of Sentrachem Ltd, was also manufacturing carbide in Newcastle, as a building block for the manufacture of synthetic rubber. In 1990, the Karbochem calcium carbide operation was closed down. In 1992, the AECI carbide business and the Karbochem production facility were amalgamated, and production continued under the Karbochem name. In 1997, the Dow Chemical Company bought the holding company of Karbochem, and the carbide business continued operations until 2003. In June 2003, the business was sold to a management consortium as SA Calcium Carbide (Pty) Ltd. Later, in October 2004, 100% of the shares were acquired by the Andina Group. Today, the Andina Group, consisting of SACC from South Africa, CIL from UK, and ANDINA from Argentina, has become a global leader in the manufacture and supply of calcium carbide and calcium silicon, ferro silicon 75% and derivatives, recarburizers with low nitrogen content, acetylene, carbon black, micro-silica, and silicon metal. The production facilities at Newcastle comprise a 52 MVA submerged arc furnace of a closed design, carbon monoxide gas recovery, recovery of fine raw materials via a hollow electrode system, and an extensive computer-controlled process. These all enable an efficient state-of-the-art operation. The downstream processing facilities consist of screening and drumming facilities, milling facilities, an acetylene generation plant, and an acetylene carbon black plant. Clearly, SA Calcium Carbide (Pty) Ltd has a long history of supplying quality calcium carbide to the industries that it proudly serves.

Jan 1, 2006

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By W. C. A. van Niekerk, M. H. Fourie

The carcinogenic potential of chromium (VI) has been the subject of numerous environmental and occupational studies, from which many regulatory efforts emanated. Besides the regulation of levels of known toxic substances (e.g. Cr (VI)), the classification of dusts for regulatory purposes has thus far depended on broad definitions of particle size, mainly used to distinguish only between inhalable and respirable particles. In the past, ultrafine particles (less than 0.1 µm diameter) (PM0.1) were often regarded as a non-issue, because it was believed that significant doses would not deposit in the lungs. A growing body of scientific data is indicating that ultrafine particles are more toxic than their coarse counterparts. Increased toxicity can be related to the unique dosimetric aspects of the deposition and disposition of inhaled ultrafine particles. Secondly, ultrafine particles have a larger surface area per given mass. The increased surface area can act as a carrier for co-pollutants, specifically transition metals (including chromium) that could form a coat on the particle surfaces during particle formation. This suggests that the presence of ?inert? ultrafine particles in the environment may enhance the potential for exposure to reactive airborne compounds, including Cr (VI). These factors are particularly important when information on occupational epidemiology is interpreted. It is desirable to consider the particle size distribution, for example when occupational exposure to hexavalent chromium compounds is assessed. Since ultrafine particles are more toxic than coarse particles with the same chemical composition, it could be speculated that cancer slope factors might be related to particle size distribution. This is relevant not only to carcinogenic chromium compounds, but also basically for any particle-associated toxicants. In general, the probability of developing health effects associated with occupational toxicants is likely to be higher when these are associated with the ultrafine particle range.

Jan 1, 2004

By T. Frömmer, H. Wagner

An inter-disciplinary geotechnical study has been carried out in an Austrian magnesite mine. The paper describes the how geological data, in situ and laboratory tests as well as subjective, empirical, geophysical and numerical methods have been used to identify critical areas in the mine. In einem österreichischen Magnesit Bergbau wurde in den letzten Jahren eine interdisziplinäre geotechnische Studie durchgeführt. Der Vortrag beschreibt den Einsatz subjektiver, empirischer, geophysikalischer und numerischer Methoden zur Identifikation geotechnischer Problembereiche Ces dernières années des études géotechniques interdisciplinaires sont effectuées dans une mine souterraine de magnésite en Autriche. Ce rapport trace l’application des méthodes subjectives, empiriques, géophysiques et numériques pour identifier les zones problématiques dans la mine

Jan 1, 2003

By B. W. Lee, P. O?Shaughnessy

The practice of manganese ferroalloy smelting has traditionally been based on utilising oxide ores which typically contain a high level of manganese. This preference for oxides has even been extended to the modification of natural carbonates into nodulized oxides. However smelting practices developed over the past 30 years have created a market for natural manganese carbonate ores, driven in part by the unique properties that this type of ore can offer. An understanding of the mineralogy of carbonate ore and its thermal properties has provided important information which enables furnace operators to take full advantage of the chemical differences. However changes to traditional operating practices have been necessary. Once furnace operations using natural and unmodified carbonate ore have been mastered, the unique chemical features of manganese carbonate ore are able to contribute, not only to new product development, but also to cost savings. The use of natural manganese carbonate ore is now a well-established aspect of the industry. The sustained increase in demand for carbonate ore worldwide over the past several years confirms acceptance of its quality. There are effectively few limits to its successful use.

Jan 1, 2004

By E. Isokangas

A mine is essentially a series of operations, including drilling and blasting, crushing, milling, flotation, and leaching, that are interconnected and therefore interrelated, with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often causes potential economic benefits and energy savings to be missed. However, the PIO methodology is a thorough approach which considers these individual process activities within the context of the whole process. The basic principle is to optimize the process as a whole, rather than each process step in isolation from the others. Metso?s Process Technology and Innovation (PTI) group offers a global consulting service for the mining and construction industries. A significant amount of this consulting work involves process integration and optimization (PIO) studies. When conducting a PIO study, every aspect of the process is considered. In addition to drilling and blasting, transportation, handling and storage, crushing, screening, grinding, flotation, separation, and recovery, other aspects including equipment utilization and energy consumption and even greenhouse gas emissions are also included if necessary. In a PIO project, it is very important to understand what type of material is being processed at any point in time. That is, which domain or domains is the material part of? This is necessary in order to observe the effect of different ore sources (and the blending of sources) on concentrator performance. Linking the ore from the pit to the concentrator required the development of an ore tracking system. As a result, PTI developed a radio-frequency based material tracking system called SmartTag?. This system allows tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles, and finally into the concentrator. Using the SmartTag? system, definitive correlations can be made between the performance of the plant and the plant feed characteristics, including the domain from which the feed ore originated. Since its commercialization in 2007, SmartTag? has been used in the majority of PTI?s consulting projects and several permanent systems have been installed worldwide1. Successful applications of the SmartTag? system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This paper describes how the SmartTag? system is being utilized by PTI and the benefits being gained by its use in PIO projects, as well as presenting some case studies.

Jan 1, 2012

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By David Mitchell, Daan Delport, Frik Marx, Mike Shapiro

The use of copper cooling elements to enhance refractory lining life in pyrometallurgical vessels is common in modern furnace design. Copper elements typically incorporate a base panel with cast in cooling passages and an integral extended surface (formed of pins, fins or similar) onto which suitable refractory material is cast. The metallic, conducting parts are located towards the cold face of the lining, with the refractory material interposing between the coolers and the process. The coolers are designed to arrest wear of the refractory material by freezing a layer of slag or partially reacted material onto the hot face, thereby rendering the lining inert to further attack [1]. These coolers have achieved success in new furnaces and relining of existing vessels. The freeze layer is prone to mechanical damage during operational and process instability. The coolers must be capable of extracting the additional heat flux under upset conditions to facilitate rapid self-repair of the freeze layer and prevent further refractory wear in the intermittently exposed areas. However, operational experience has shown that the high heat flux capabilities of the copper coolers have some disadvantages, especially in processes producing vapours which form corrosive compounds when condensing onto the cold surfaces of the coolers. When corrosive conditions develop, the entire composite will fail due to loss of structural integrity, and as a result of leaks from the cooling water passages. This paper describes recent developments in the approach to the design and manufacture of copper cooler panels customized to achieve specified heat fluxes and temperature profiles, thereby reducing the formation of corrosion mechanisms in applications with corrosive gaseous environments and enhancing refractory lining life. Condensation formation prevention is achieved by adjusting the geometry of the cooler and selection of suitable materials of construction.

Jan 1, 2007

By Phillip J. Mackey, Rodney T. Jones

"Copper and copper alloys remain key materials for society today, with important uses found in the electrical, transportation, and construction industries. Copper demand is rising, with projections indicating that by 2025 global refined copper demand will increase to 29.5 million tons, up from the 22.4 million tons anticipated for 2015. This will require the opening up of dozens of new mines and numerous new smelters over this time period. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in contributing to meeting the rising global demand for copper. This paper provides a brief overview of the current copper smelting operations in Southern Africa. INTRODUCTION Copper and copper alloys are essential materials for today’s modern world. The familiar green copper patina colour seen on buildings and other structures sometimes belies its true “green” characteristic – copper is essential for key emerging technologies such as wind turbines, tidal generating systems, solar energy systems, electric cars and the like. Consequently, it is believed that there will be continued growth in copper demand in the years ahead. Projections indicate that by 2025, as an example, global refined copper demand will increase to 29.5 million metric tons, up from the 22.4 million ton level anticipated for 2015. This will require dozens of new mines, and of the order of the equivalent of 10 to 12 new 0.5 million tons of copper/year-sized copper smelters (after factoring projected copper produced by electrowinning (EW))—overall, a huge undertaking. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in supplying this rising global demand for copper. Africa’s share of global mined copper production was about 10% in 2014; however this will increase significantly in future if announced new projects eventuate. Southern Africa has an important role to play in this process. The present paper provides a brief overview of copper smelting in Southern Africa."

Jan 1, 2015

By N. Mulaudzi, S. Archer

"Direct cobalt electrowinning was developed to produce unrefined cobalt metal as an alternative to producing a mixed hydroxide product (MHP), which is the common cobalt intermediate product in African Copperbelt operations. MHP is preferred due to the high cost of producing high-grade cobalt cathode. Direct cobalt electrowinning test work results have shown that the purity of the unrefined cobalt metal produced from a low-grade copper solvent-extraction raffinate stream was ~97% (w/w), which is significantly higher than the MHP purity (up to 45% (w/w) Co). The current study investigates whether direct cobalt electrowinning would increase the profitability of African Copperbelt copper–cobalt oxide operations, when compared with the MHP flowsheet. An order-of-magnitude economic evaluation was conducted using dynamic differential discounted cash flow models on a “bare-bones” basis, using a 10% discount rate. Three variables were evaluated, namely; reagent utilisation extents, precipitation extents and filter-press wash efficiency. Multivariable risk analysis was also conducted using the Monte Carlo simulation technique to understand the impact of key project drivers. The financial study results indicated that a direct cobalt electrowinning flowsheet could potentially result in a higher mean net present value (NPV) compared with the MHP flowsheet. Cobalt recovery was found to have the most significant impact on the NPV. In addition to increased profitability of African Copperbelt operations, direct cobalt electrowinning has the potential to reduce the environmental footprint of operations as well as addressing the Democratic Republic of Congo government’s drive towards export of higher value metal products instead of low-grade intermediates."

Jan 1, 2015

By J. A. Bakken, G. Sævarsdóttir, H. Pálsson, M. Þ. Jónsson

The role of the electric arc in the consumption of electrodes in submerged arc furnaces has long been debated. The hostile environment in the furnace does not make direct measurement feasible, so simulation has been used to evaluate the arcs contribution to the erosion. Magnetofluiddynamic (MFD) electric arc simulations and a cathode / anode sub-model developed in order to provide boundary condition to the arc model have been used for this purpose. The cathode / anode sub-model provides current distributions and cathode / anode fall voltages for the arc and temperature distribution for the electrode surface, which is paramount to the erosion rate which in turn is calculated from the Clausius Clapeyron equation and the Hertz Knudsen formula for the vapour transport. In the case of high-current industrial AC arcs, arc currents are typically ~100 kA, phase voltages ~100 V and total furnace power ~10 ? 60 MW. The results show that although enormous amounts of material is evaporated, much of it recondenses on the surface. Furthermore the results show that the arc erosion increases strongly with the arc current. If a single arc is present its contribution to erosion is close to the actual total erosion in the furnace. Results from this analysis indicate that there are possibly more than one arc present in the crater, in which case less than 40% of the total erosion would be due to the arc, the rest is chemical erosion.

Jan 1, 2007

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

By M. Dhainaut

This paper presents computations of the electric field inside a furnace. We first look at the effect of contact between two coke particles from an electrical point of view. We give values for the amount of contact resistance in the total resistance of the system formed by the two coke particles. We show that the effect of contact resistance decreases rapidly with increasing contact area. We then look at the complete electric field inside a full scale furnace. The aim is to evaluate the amount of current that short-cuts the metal bath for different vertical positions of the electrodes. We show that electrodes high above the metal bath are undesirable since they offer a larger surface of conductive charge materials where current can flow through. On the other hand, deeper electrodes force the current to go the whole way down to the metal bath. Ohmic heating along this path ensures a high temperature of coke and slag that are beneficial for metal recovery.

Jan 1, 2004

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. 'ferromanganese'. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007