Search Documents

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By Thomas J. Peters

The U.S. Bureau of Mines conducted a mineral investigation, and the U.S. Geological Survey did a geological appraisal of an east portion of the Bear-Marshall-Scapegoat-Swan (BMSS) RARE II area (No. A1485) to provide mineral resource information for land use planning. The Bureau of Mines' investigation consisted of a library and field search for all mineral properties and occurrences, and included a review of Teton County mining claim records. Those records showed two placer claims, the only mining-related activity known in the area. Six reconnaissance pan samples were taken in the vicinity of the two placer claims, the Lone Star and Spotted Horse, located on Hannan Gulch in 1900 and 1901. One sample contained a trace of gold, but there are no identified resources. However, the study area is in the Rocky Mountain Overthrust Belt, which is productive for oil and gas elsewhere. The entire study area is blanketed by oil and gas leases and is currently being explored.

Jan 1, 1983

By R. E. Brown

The objective of this Bureau of Mines study was a laboratory-scale evaluation of the sodium sulfate refining process for removing copper from molten ferrous scrap. Maximum copper removal is achieved in carbon-saturated melts at 1,300° C. Low carbon concentrations and higher temperatures result in a less efficient copper removal and an increased sulfur concentration in the iron. Sodium sulfate refining significantly lowers the concentration of aluminum, manganese, and silicon; however, the copper removal efficiency is adversely affected by the presence of manganese and silicon. Compared with other reagents tested, sodium sulfide-forming slags were found to be the most suitable for both copper removal and sulfur control. The sulfur content of the refined iron was higher in tests conducted in acid-type refractory crucibles. Earlier studies showed that tin, a significant metallurgical impurity, is not removed by the sulfate process. During the present investigation, results showed that chlorination, using organic solid sources of chlorine, reduced the tin concentration to acceptable levels in molten iron.

Jan 1, 1975

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By Doris M. Hyde

The impact of mining activities on the economy in both 1983 and 1984 was minimal. The most recent available data on the gross domestic product (GDP) indicated a level of $1.6 billion in 1983.2 The estimated value for the production of cement, aragonite, and salt was about $17 million in that year, down from the estimated $20 million in 1982. No data are available on the economic impact of the large petroleum refinery at Freeport on Grand Bahama Island, but it represents the major mineral-related activity. Cement production remained at only a fraction of the 800,000 tons per year of plant capacity. The offshore search for hydrocarbons continued in 1984, and some companies were about to enter the third year of seismic and geological surveying around Andros and Grand Bahamas Islands. Getty Oil (Bahamas) Co. Inc.; Breoco Ltd., a subsidiary of REO Development Corp. of Tulsa, Oklahoma; and Natomas Petroleum (Bahamas) Ltd. were the first companies to be awarded exploration licenses. These companies were committed to drilling at least one well before the end of the third exploration year. Other companies actively engaged in exploration included Exxon Corp., Atlantic Richfield Co. (ARCO), Chevron Oil Bahamas Ltd., and Esso Oil Bahamas Ltd. Geophysical Services Inc. (GSI) of Dallas, Texas, and Petroleum Services (Bahamas) Ltd. of Englewood, Colorado, ran another seismic survey line during 1984. This 1,533-mile line was in the Great Bahama Bank and Cay Sal Bank areas off the southeast Florida coast, and tied in with a 4,530-mile program GSI ran in 1981-82. These surveys were nonexclusive and publicly available through GSI.

Jan 1, 1986

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By G. G. Morgis, J. J. Forbes

"INTRODUCTION The greatly diversified and increased uses of beryllium and its con& pounds in recent years have focused attention on the health hazards incident thereto. The Bureau of Mines has a fundamental interest in safety and the elimination or reduction of health hazards in the mineral and allied industries, and it recognizes that serious hazards are inherent in the production and use of beryllium and its compounds. This circular presents a review of the literature pertaining to such health hazards but does not describe original research by Bureau personnel. Most of the bibliography has boon either quoted in part or abstracted in an effort to present information in a comprehensive and readable form.In reviewing the literature, differences of opinions wore recognized in the writings of the respective authors, but no attempt was made to evaluate such differences. This presentation was devoted strictly to reporting without editorial comment.SUMMARYAlthough beryllium was known to industry for about 150 years, its toxicity did not present any serious problems in the United States until the advent of World War II, when the increased use of this element and its compounds brought to light several toxicologic reactions occurring primarily in the lungs and skin of workers handling it. The pulmonary effects, characterized as acute pnoumonitis and chronic pulmonary granulomatosis in beryllium workers, are far more serious than the dermatological manifestations.The addition of beryllium to the list of toxic industrial metals has boon so recent that there is still some confusion in the clinical picture. Data on magnitudes of exposure likely to be responsible for the production of disease are not yet adequate. There appears to be no relation between the severity of exposure and the development of cases some of those having had severe exposure have not developed a reaction, whereas those having a slight exposure in some instances have developed a response."

Jul 1, 1950

"It is evident that the incidence of coal worker's pneumoconiosis (CWP) or black lung disease varies in different coal producing regions of the United States. Many people have hypothesized about the reasons for the differing occurrences. Because underground coal mining involves many mining methods under changing geological conditions, several factors may be involved in contracting CWP such as: the amount of quartz in the respirable dust, the trace elements in the respirable dust, the rank of the coal that produced the respirable dust (bituminous, anthracite), the amount and size of respirable dust, etc.Recognizing the uniqueness of underground coal mining and CWP, research investigations involving seam characteristics, mining system and worker position are being conducted in the center to establish standard procedures for characterizing some coal properties that may be involved in workers contracting CWP. This has been accomplished by the in-mine sampling of airborne dust at various worker locations and mining system configuration and by performing laboratory analyses of mined material (coal and rock) taken from the mines. (FIGURE 49 and 50)The investigations includes a method of classifying coal seams according to their potential to generate respirable dust. It includes statistical analyses of the size and locational variations of the elemental compositions of respirable coal mine dust in operating underground mines from seams located in the eastern, midwestern, and western United States, and is currently completing research which is investigating the relationship between the elemental compositions of respirable dust sampled near a continuous-mining machine and a laboratory-produced respirable dust."

Nov 1, 1988

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By James E. Hill

The Bureau of Mines has been carrying on an extensive diamond- drilling program during the past 7 years on deposits of strategic and critical minerals . Often the project reports and the drill-hole logs describe the findings only in terms of the mineral being sought at the time . Then , too , results may not always be interpreted alike by several mining engineers , and the cores therefore provide a permanent tangible record to complement the project reports . The cores from projects in the eastern divisions are being stored at the Mount Weather Testing Adit . Core from a representative hole ( or skeletonized sections from several holes , if these are more representative ) is selected at each project and shipped to Mount Weather for permanent storage . At the Testing Adit an underground room was prepared and storage racks were installed . Wooden core trays designed to accommodate cores of various sizes were purchased .

Apr 1, 1947

By J. E. Pahlman

As part of its goal to minimize the requirements for mineral commodities through conservation and substitution, the Bureau of Mines is conducting research to determine the resistance of alumina refractories to corrosion by alkali-containing slags that could result from burning of the abundant Western lignites in metallurgical operations. Static corrosion tests were performed at 1,000° to 1,350° C and dynamic tests were performed at 1,400° to 1,600° C to investigate the stability of refractory specimens in slag environments. In general, the degree of refractory attack increased with decreasing alumina content in the refractory and with increasing alkali content of the lignite ash. The parabolic kinetics observed in static tests suggested that a reaction product layer is formed through which ionic diffusion must occur to sustain the reaction with the refractory material. The linear kinetics observed in dynamic tests in high-viscosity slags indicated a shearing of the reaction product layer by viscous slags. The observed lesser attack of refractories by low-viscosity slags can be explained on this basis. Two 99-percent-alumina refractories and two 90-percent-alumina refractories formed an expanded protective layer with the more viscous slags but not with the less viscous slags. Corrosion of 90-percent-alumina refractories increased exponentially with temperature. In refractories with the same nominal alumina content, those that contain a combination of a-Al203 and mullite (3A1203?2Si02) have better corrosion resistance than those containing a combination of a-Al203, cristobalite (Si02 mineral), and mullite. In alkali environments (1,300 to 1,400° C), 90-to 99-percent-alumina refractories are recommended for use as furnace linings.

Jan 1, 1980

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

This chapter presents data on occupational exposures from several sources. Data from compliance samples obtained by MSHA inspectors are presented in table 6-1 for coal mine dust and silica dust, and in tables 6-2 through 6-6 for metal fumes. Since these samples were taken for compliance monitoring rather than as part of a survey of the industry, it is difficult to predict how well they indicate actual exposures for all mining operations. In the coal industry, 7.8% of all respirable dust samples during 1986-1995 were above the permissible exposure limit (PEL). Of silica dust samples obtained during the 10-year period, 23.7% were above the PEL in coal, 16% in metal, 10.8% in nonmetal, 9.1% in stone, and 7.6% in sand and gravel. Of metal fume samples, silver samples showed the largest percentage above the PEL-approximately 48% of samples in both metal and nonmetal. Tables 6-7 and 6-8 present data on noise exposures from the MSHA "dual threshold" survey, which was published in the Federal Register [61 Fed. Reg. 66347 (1996)] as part of a proposed rule change for occupational noise exposure in mining. This study examined a group of samples obtained during 1991-1995 and compared the percent of samples that were above two separate specified limits. The first limit was the current noise standard, a time-weighted average of 90 dBA, calculated to include only exposures at 90 dBA and above. The second limit was a time-weighted average of 85 dBA, calculated to include exposures at 80 dBA and above. Tables 6-8 and 6-9 refer to musculoskeletal overload conditions examined in the National Occupational Health Survey of Mining (NOHSM) [NIOSH 1996]. Table 6-8 shows the operational definitions for each condition; table 6-9 shows the percentage of the workforce potentially exposed, by commodity. Across all commodities, a large proportion of workers were exposed to musculoskeletal overloads due to positioning of the neck and back; positioning and motion of the forearms, arms, and shoulders; heavy lifting; and positioning and movement of the lower limbs. The recorded overloads were defined in the survey and did not exceed any NIOSH, MSHA, or OSHA guidelines for musculoskeletal overloads. Further information on this survey appears in appendix A.

Jan 5, 2000

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968

By Kathleen Madland Kowalski

In recent years the issue of human stress response in emergency workers has begun to receive attention. This paper presents a rationale for considering human stress as a significant factor in the management of emergencies It discusses the concept of stress, Critical Incident Stress in emergency responders, and intro¬duces the Critical Incident Stress Debriefing (CISD) process. It is suggested that in a disaster, the CISD process can improve the effectiveness of response teams on site, their turnaround time on site, and post disaster time off the job. This paper, prepared by a US Bureau of Mines research psychologist, offers some ideas to the mining industry in general, mine rescue trainers and more universally, to those responsible for developing emergency management plans.

Aug 1, 1998