Search Documents

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By Edward Thomas

In 1947 the Bureau of Mines, as an accident-prevention measure, decided to advocate the adoption of roof bolting (suspension roof supports) in coal mines where it appeared to be applicable. Subsequent experience has disclosed that the applicability of this support is more general than was first suspected; moreover, comparison of the accident records of mines before and after adoption of the roof-bolting method shows results that more than justify the effort and funds expended. The industry has responded enthusiastically, because roof bolting proved to be not only an accident-prevention measure but also one to increase productive efficiency. In some instances this increase in the productivity of men and machines has been almost incredible and has led many mining men to conclude that through some hocus-pocus they can now cast aside many or all of the time-proven rule of good mining practice. If this tendency is not counteracted, it could easily result in an increase of roof-fall accidents, which may outweigh the benefits of roof bolting and discredit an innovation in roof control that shows great promise of materially reducing our mining accidents. From an economic standpoint it may represent the margin between profit and loss in many mining operations. The purpose of this manuscript is not to propose an inflexible code or set of rules but to summarize the experience to date as a guide for those who have the responsibility for the installation and inspection of roof bolts. This experience consists of approximately 250 investigations of roof failure in which roof bolting was involved either directly or indirectly. It should be pointed out that many of these failures were controlled, occurring during experimental periods, and comparatively few of the accidental failures actually resulted in personal injury, yet a significant number represented potential hazards.

Jan 1, 1951

By M. M. Fine

A preliminary mineral-dressing study of five samples of East Texas limonitic brown iron ores was conducted as part of the Bureau of Mines program to develop and extend domestic resources of iron ore. The samples were considered to be typical of ore currently being mined and beneficiated by the Lone Star Steel Co. and Sheffield Steel Co. The objective of the research was to investigate those mineral-dressing unit operations that might recover some of the fine iron lost in current industrial wastes or perhaps improve the recoveries when applied to the ores as well. Since current industrial beneficiation practice yields a washed limonite analyzing 41 to 45 percent iron, higher grade concentrates were not sought in this laboratory study. Laboratory investigation included washing and sizing, reduction roasting, and subsequent magnetic separation of the finely ground roasted materials. The results showed that laboratory recoveries of over 80 percent of the iron were possible, for the ores investigated, at concentrate grades comparable to those expected from cur-rent industrial beneficiation practice. ACKNOWLEDGMENTS Acknowledgment is made to the Lone Star Steel Co. and Sheffield Steel Co. for supplying the brown iron-ore samples on which this research was conducted.

Jan 1, 1956

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By J. L. Stauffer, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Eicosanoids and cytokines produced by alveolar macrophages (AM) are key mediators of pulmonary inflammation and fibrosis. In order to determine if eicosanoid production and cytokine production are altered in AM obtained from coal miners, we compared production of prostaglandin E2 (PCE2), thromboxane A2 (TXA2), leukotriene B4 (LTB4), interleukin-1 beta (IL-1B ), and tumor necrosis factor alpha (TNfa.) by cultured AM from normal human subjects and coal miners. The recovery of AM from miners' lungs by bronchoalveolar lavage was significantly greater than that from control subjects. Mean eicosanoid and cytokine production by AM from active miners was also increased compared to AM from control subjects, but this increase was not statistically significant. AM from control subjects produced significantly more TXA2 and TNFa. when exposed to lipopolysaccharide than did AM from miners. The cyclooxygenase inhibitor suprofen reduced PGE1 and TXA1 production and TNF0t. release but had no effect on LTB4 production or IL-1B release by miners' AM. The lipoxygenase inhibitor nordihydroguaiaretic acid attenuated TNFa release, as well as that of LTB4, but had no effect on IL-1B release. Inhibition of thromboxane synthase by UK 38,485 also reduced TNFa release by active miners ' AM but had no effect on PGE1, LTB, production, or IL-1 f3 release. The results of these studies suggest that occupational inhalation of coal dust may increase total lung eicosanoid and cytokine levels and reduce the reactivity of AM to bacterial endotoxin. Furthermore, coal dust-induced changes in both eicosanoid and cytokine release may be subject to pharmacological modulation.The alveolar macrophage (AM) is a primary defensive cell in the lung and is one of the first cell types to encounter inhaled mineral dust. The response of the AM to invading foreign material is designed to enhance the defensive capacity of the lung. However, in the case of occupational inhalation of mineral dust particles, this response may be inappropriate, resulting not in the defense of the lung but in chronic inflammation and fibrosis (Rom et al., 1987; Takemura et al., 1989). The reaction of the AM to chronic mineral dust exposure may involve the exaggerated release of paracrine mediators of lung function, including eicosanoids (oxygenated derivatives of arachidonic acid) and peptides, including cytokines and growth factors (Sibille & Reynolds, 1990). Eicosanoids are involved in bronchial and vascular smooth muscle reactivity, vascular permeability, fibroblast growth, and the recruitment of additional immune cells to the alveolar space (Barnard et al., 1992; Elias et al., 1985; Scott et al., 1982). AM-derived cytokines such as interleukin-1 beta (IL-1 B) and tumor necrosis factor alpha (TN Fa) have a variety of biological activities including the regulation of fibroblast growth and proliferation (Becker et al., 1989; Libby et al., 1989; Schmidt et al., 1984). Interestingly, in vitro studies with macrophages suggest that the production of cytokines may be linked to eicosanoid production, in particular that prostaglandin E2 (PGE2) may down-regulate IL-1 f3 and TN Foe production by the AM (Bonta et al., 1989; Kunkel et al., 1986; Monick et al., 1987)."

Dec 1, 1996

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By Raymond B. Ladoo

Silica , or silicon dioxide , ( Si0, ) , occurs in a free state chiefly as quartz , but hydrous silica ( amorphous silica carrying a variable amount of combined water , 2 to 13 per cent ) , occurs as opal , flint , diatomaceous earth , tripoli and so on . Quartz is found in many forms , the most important of which are ; As vein quartz; quartzite ; sandstone ; silica sand and gravel ; as crystals or crystalline grains , masses or aggregates in igneous rocks such as granites , dicrites and pegmatites . Commercially silica is used in many ways , but ordinary uses of sand and gravel are so well known that they will not be considered here .

Jan 1, 1922

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By Michael S. Miller

The Carson-Iceberg RARE II study area, consisting o; 209,990 acres (134,983 ha), is on the crest of the Sierra Nevada in California, about 35 mi (56 km) south of Lake Tahoe. The area is divided into four parts: C4-986; C5-986; and B5-986, north and south portions. No mineral production has been recorded for the area. However, gold, silver, and tungsten resources and potential for additional resources have been estimated for the area and just north of area C4-986.

Jan 1, 1981

By George S. Rice, J. W. Paul, E. H. Denny

Data assembled by the Bureau of Mines , coupled with requests from coal companies , have emphasized the desirability of establishing standardized specifications for brattice cloth with particular respect to durability and fireproofing . Brattice cloth is a canvas or other material , often covered with some fireproofing composition , which is used extensively in coal mining for temporarily deflecting air into pillar workings and maintaining ventilation at the working faces . These specifications will be established , it is planned , through a cooperative program in which the U. S. Bureau of Standards will make a series of tests of various brattice cloths treated with respect to fire- resisting qualities and the U. S. Bureau of Mines will continue to assemble field data on the use of brattice cloth . Plans now are being made for this cooperative work. Without attempting to make a complete survey , the Bureau of Mines has made preliminary studies and investigations , and verious representative coal - mining companies have furnished detailed information . The information thus gained will be used as the basis for the cooperative investigation , but the Bureau of Mines would welcome additional information from mine operators on the character and weight of brattice cloth , conditions of use , durability , quantity employed and price . Such information should be sent to the Director , Bureau of Mines , Washington , D. C. The mine operator is interested in procuring at reasonable cost a brattice cloth with lasting fireproofing quality and of as great durability and strength as possible . There has been a lack of assembled data and knowledge regarding the subject , but the Bureau of Mines feels that this lack of knowledge may be overcome if the coal -mining companies will lend their hearty support to the cooperative investigation and submit information relative to the use of brattice cloth in their own properties . Information contained in this report is based on data obtained from coal operators in bituminous districts of Pennsylvania , Alabama , Utah , Indiana , Illinois , Colorado and Nova Scotia .

Feb 1, 1923

By Richard L. Rains

In 1984 and 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 162,887-acre Mormon Mountains Wilderness Study Area (NV-050-161) in order to evaluate its identified mineral resources. The study area is located in Lincoln County, NV, about 60 miles northeast of Las Vegas. The study area had no mines or mining claims in 1985, and no mineral resources were identified within the study area, or at the Whitmore mine or Iron Blossom prospect near the study area. The alluvial fans around the southern boundary are staked with about 450 placer claims. Chemical analyses of samples indicate that some limestone in the study area is suitable for manufacturing cement or for agricultural purposes but the limestone is distant from markets and therefore not economic in the foreseeable future. The study area is blanketed with oil and gas leases, but no known productive horizons were identified.

Jan 1, 1986

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.5 and 3 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year product Lon period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 Indexes. Initial capital investment is $33.8 million for the 1.5-MM-tpy mine and $61 million for the 3-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $52.5 and $94.2 million, respectively. These figures translate into total capital investments of $34.87 and $31.31 per ton of annual production. Assuming a desired 15-percent discounted cash flow rate of return, with Federal income taxes at 50 percent, the required selling prices would be $12.06 and $10.94 per ton for the 1.5- and 3-MM-tpy mines.

Jan 1, 1976

By B. T. McClure

Oxidizing catalytic converters are sometimes used by underground mine operators as an emission control device to reduce odor, hydrocarbon (HC), and carbon monoxide (CO) emissions from diesel equipment. The objectives of this report are to quantitatively assess the effects of catalytic converters on diesel exhaust emissions and to make recommendations for their use. Information in this report is from a literature survey and contract research supported by the Bureau of Mines. Catalytic converters are effective in reducing CO, HC, and odors when the exhaust temperature is high enough so that the converter remains above 250° C. Converter temperature is dependent upon engine duty cycle. Catalytic converters increse sulfate emissions and slightly in- crease oxides of nitrogen (NOx) emissions. If low sulfur fuels are not used, the increase in sulfate and nitrogen dioxide (NO2) emissions can offset any advantages of the catalytic converter as measured by the emissions quality index (EQI). In addition, in vitro bioassays have shown that catalytic converters produce soluble organic compounds, which have increased mutagenic activity with respect to untreated exhaust. Based upon criteria recommended by a joint Canadian-United States research panel, catalytic converters should only be used in special circumstances in underground mines. Vehicles equipped with catalytic converters should operate under moderate to heavy load conditions, and use fuel with a sulfur content less than 0.1 pct.

Jan 1, 1988

By G. S. Scott, G. W. Jones

Trichloroethylene (CHC1CC12) is an important solvent for fats , resins , bitumens, rubber , sulfur , and phosphorus . It is used extensively in drycleaning because of its low order of combustibility and has recently been proposed as an inhalation anaesthetic . Its physical properties have been described by Carlisle and Levine . It is usually considered a noninflammable material ; however , substances that are noninflammable when mixed with air are not necessarily noninflammable when mixed with oxygen . Thus , Hewer's statement that " Trichloroethylene*** is not inflammable under any circumstances , nor will its vapor explode when mixed in any proportion with air , oxygen, or nitrous oxide , " requires qualification , especially in anesthesia, where pure oxygen may at times be substituted for air , This report gives the results of tests made to determine the inflammability of trichloroethylene in various mixtures of oxygen and nitrogen . The trichloroethylene used was Eastman's No. 1300. The boiling point was given as 86 ° to 87 °C . The specific gravity and refractive index of the sample measured in this laboratory were , respectively, 1.45 and 1.4759 at 25 °C .

Nov 1, 1942

By Lewis V. Wade

This report provides background information concerning a mine roof simulator currently being considered by the Bureau of Mines. The simulator is a mechanical device with the ability to simulate the forces and displacements associated with mine roof over an area 20 by 20 feet. The topics covered in the report include a conceptual description of the system, definition of system capabilities, discussion of how such capabilities were decided upon, description of available control modes, and a comparison between the mine roof simulator facility and similar facilities existing elsewhere.

Jan 1, 1974

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

By Daniel E. Sullivan

The recession of 1974 continued into 1975. Real gross national product (GNP), measured in 1972 dollars, declined significantly in the first quarter of 1975 but rose slightly in the second and increased sharply in the third quarter. Unemployment peaked during the second quarter and then declined slowly for the balance of the year. The inflation rate declined owing to reduced demand and smaller-than-1974 increases in energy and food prices early in the year. Recovery was clearly evident by yearend, though un-employment and inflation remained at high levels. Total output as measured by the GNP in current dollars rose 6.5% in 1975. Real GNP declined 2.0%, and inflation, as measured by the implicit price deflator, increased 8.7%. Real gross private domestic investment for residential structures declined 18.1% in 1975, which was a smaller rate of decrease than the 27% decline in 1974. Real State and local Government purchases increased 2.4%, and real personal consumption expenditures for services rose 1. 7 %. The Federal Reserve Board (FRB) index of industrial production declined 9.7%.

Jan 1, 1977