Search Documents

By A. M. Bell

"The property of Gaspe Copper Mines, Limited, is in the Gaspe Peninsula some 60 miles west of the town of Gaspe and 20 miles in from the north coast. The Copper Mountain deposit was first discovered in 1921 and first optioned and drilled by Noranda in 1938. The Upper Needle Mountain showings a mile south were found in 1938, but it was not until after a delay of 10 years that the more important deep ore at Needle Mountain was located by drilling. Production started in 1955, and the smelter commenced operation in December. Mining is by open stope methods with first production coming from the Lower Needle Mountain orebody, of which only a small portion has been exposed in underground openings.Stratigraphy and AlterationThe country rock is composed of limy siltstones of Devonian age. Away from alteration these are dark and generally carbonaceous. Throughout the drilled area numerous narrow layers of tuffaceous fragmental material occur, and such beds are found to provide excellent horizon markers by virtue of their uniform thickness and wide lateral distribution. These markers are valuable for stope control in mining the bedded replacement deposits.Intruding the sediments at Copper Mountain are porphyry dykes, and one drill hole encountered granite 1,400 feet below the valley. Solutions responsible for the rock alteration and ore deposits seem to have emanated from this intrusive centre.On the mine claims strong hydrothermal alteration has completely obscured the original character of the sediments. The unaltered formations are all very similar in appearance, but following alteration rocks that are very dissimilar in physical characteristics are produced, and such differences have an important influence on ore deposition. The alteration effects are known to extend over a vertical range in excess of 3,000 feet and have a surface area of two square miles. All known ore bodies are within the zone of alteration. In this, rocks are strikingly bleached to a white colour in contrast to the normal dark-coloured sediments, and are much harder and more abrasive, with bedding often obscured. The first effect of alteration is driving off of carbonaceous matter, followed progressively by silicification in the acid rocks and by the formation of lime silicates in the lime rocks, with an accompanying gain in silica and a corresponding loss in lime. Extensive analysis has shown that there is an actual addition of silica involved in the alteration."

Jan 1, 1949

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations for the smelting and refining of non-ferrous metals, and it is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate. It is also the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y zinc. Since then, production capacity has increased, and at present, it stands at 240,000 t/y zinc. In this paper, the leaching process and particularly the operation of the jarosite circuit is reviewed, specifying process improvements to treat high iron calcines.INTRODUCTIONTwenty years ago the Electrolytic Zinc Plant in Peñoles was treating high quality zinc concentrates with low concentrations of iron (~7.5 wt.%) and silica (1.8 wt.%). Nowadays the quality of zinc concentrates is poor with a typical iron content of around 11 wt.% and silica at 2.0 wt.%. This has created numerous processing problems in our roast-leach-purification- electrolysis sections. In order to meet customer requirements it is necessary to find processing solutions to assure the operational continuity of the plant. These processing solutions are the focal point of this paper.REVIEW OF THE LEACHING PROCESSThe purpose of the leaching process is to recover the metals, mainly zinc, through a series of extraction stages with sulphuric acid solutions, which progressively increases the zinc dissolution. After the series of acidification stages, the solution, which is rich in iron, is sent to the jarosite circuit to separate zinc from iron (Garcia & Valdez, 1996). The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper. Then this solution is sent to the tank house to feed the electrolytic cells."

Jan 1, 2016

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019

By V. Ogarlaci

Over 90% of the Romania's lignite reserve is located in the region of Oltenia, which is why this area is given special attention in the country's coal resources. Because the lignite deposit of Oltenia is comprised of 1-8 exploitable coal layers, their capitalizing calls for urgent arrangements to ensure rational exploitation under conditions of total safety, minimum losses and efficiency. The technology used the coal pits of North-Western Oltenia is the technology of excavation, transport and dumping in a continuous flow by using the complexes of excavation, transport and high-capacity dumping. The theme of this paper is of particular importance because the rhythmic operation in complete safety, is necessary both for sizing and keeping within the bounds of acceptable values, throughout the process of excavation of the geometric elements of the coal faces, marked by: the height of benches, slope angle and width of berms. Geometric dimensions of the benches of the open pits, the height of benches, slope angle and width of berms shall be calculated and shall be based on: the massif structure that forms the benches; physical-mechanical characteristics of rocks from the bench; working conditions, characterized mainly by mining and extraction methods applied; functional parameters of the mechanical equipment used to perform various operations on the coal face etc. For this study it was necessary a broad field for task tracking, measurement, research and design elements of the coal face, for land survey and a desk activity by: processing of topographic data, laboratory analyses on physical and mechanical properties of rocks and numerous specialized studies. In the final part, we bring some contributions to elucidating the issues of special importance for the lignite coal pits of Oltenia, coming up with data, graphics, formulas, solutions and concrete dimensioning of coal faces in terms of using technology in a continuous flow.

Aug 1, 2013

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By P. E. Mather, M. J. M. Krane

Uncertainty quantification is a means of articulating the reliability of model estimations. Models of copper pyrometallurgical processes have been published for decades but discussion of their reliability has typically been terse and qualitative, mitigating understanding of their exact applicability to industrial situations. This presentation shows basic uncertainty propagation and Bayesian model calibration, two powerful uncertainty quantification tools, applied to a reduced order model of copper fire/anode refining. The implications of the uncertainty quantification analyses on the applicability of the model results to industrial practice are then discussed. Finally, other possible applications of uncertainty quantification to copper extractive metallurgy are explored. INTRODUCTION Modern copper production operations, including mining operations through wire drawing factories, are ubiquitously heavily instrumented. Most mine-sites and smelters have large repositories of historical data. That said, much of this data is not exploited to its maximum effect. This proceeding provides examples of using uncertainty quantification (UQ) to maximize the informational yield of the data collected from a fire-refining operation. Anode/Fire Refining is the final pyrometallurgical step in the production of copper anodes; it is an essential and universally employed processing step at smelters (Schlesinger, King, Sole, & Davenport, 2011). Much like the smelting and converting furnaces further up the process stream, anode furnaces are difficult to instrument due to their high temperature and the corrosive and/or caking quality of their offgas. This makes continuous and accurate measurement of the streams leaving the unit operation, e.g. liquid copper, slag, and offgas very difficult. As an example, offgas flowmeters, while providing continuous draft values, could miss the actual draft value by tens of percent due to caking or corrosion. UQ methods account for the uncertainty in process measurements and parameter values; they use a process model with measurements of performance indices to provide better and better estimations of process performance. This proceeding will first introduce a surrogate model for copper fire refining, made from a 1D, transient, reacting flow model of the process presented elsewhere in these proceedings (Mather & Krane, 2019). Discussion of the data used to make the surrogate model, as well as the creation of the surrogate model, will be included. Then, a Monte Carlo simulation will be performed, showing the expected soot production rate based on the surrogate model and assumptions about the uncertainty in the model’s parameters. Finally, the surrogate model parameters will be calibrated in a Bayesian way; this will tell what the actual uncertainty in the parameters are, given a set of observed industrial data and prior assumptions of the observations’ and parameters’ uncertainty.

Jan 1, 2019

By Libao Zhu, David J. Williams, Nazife Erarslan

"Statistics show that the drawbell in underground mines is usually subjected to significant damage by impact loading due to falling ore. Drawbell damage causes a large quantity of residual ore to remain on the drawbell, thus leading to a huge waste of ore resources. In this study, the Cavity Monitoring System (CMS) and Surpac software were employed to visualize the 3-D damage. Also, the Discrete Element Method (DEM) was employed to perform simulations of the falling ore to investigate the damage evolution of drawbells under repeated ore impact and obtain the dynamic damage accumulation mechanism. The reason of drawbell damage was found due to the micro-shear cracks. The numerical simulations of a drawbell damage process under repeated impact loading showed the main failure type was shear failure and this type damage was found increasing with more ore falling. INTRODUCTIONDrawbells are an important part of underground mines and play a significant role in ore recovery in terms of safety, economy and efficiency (Brunton et al., 2010; Hustrulid & Bullock, 2001; Trueman et al., 2002). In most cases, blasted ore is gravitated along the drawbell and finally arrives at the footwall of the drawpoint. However, some of the blasted oversize ore blocks clog the drawbell road and those ore pieces are called hang ups (Penswick, 1997). However, any damage on a drawbell is believed to be the reason for these hang-ups. In the literature, researchers have reported that the stability of the draw-point is influenced by the stress distribution above and near the drawbell (Butcher, 1999; Neverov & Neverov, 2013). Much research in the literature has been done on draw-points in underground mines. In fact, rockfalls cause very serious damage on a small impact area in a very short time (Volkwein et al., 2011). Hoek (2000) pointed out that the blasted ore causes progressive ravelling and even collapse of the drawpoint, thus the ore in the stope is abandoned. In this paper, the Cavity Monitoring System (CMS) was employed to obtain the damage profile of a drawbell due to the impact of rockfalls and to confirm the residual blocking ore on the damaged drawbell. Then, the drawbell damage evolution due to repeated falling ore was simulated by the Discrete Element Method (DEM)."

Jan 1, 2015

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By A. A. Nourbakhsha

The main application of refractories based on andalusite in ferrous metallurgy are in air heaters of blast furnaces, mobile mixers, and hot-metal transfer, pig iron ladle, steel-casting, and intermediate ladles. Three specific properties of andalusite are very interesting for the production of high-quality shaped and unshaped mullite refractories: being free of water, its crystal a remains stable without changing its density or volume after firing and therefore has no internal porosity .Graphite additives due to its great wetting ability play an important role in raising the property of refractory bodies. In order to improve properties of andalusite graphite bodies, oxidant agent for increasing in hot strength and oxidation resistance can not be avoided. In this research, firstly 8 pig iron ladles from ESC(esfahan Steel company) with different conditions selected and monitored during usage to determine of main factors affecting on corrosion of refractories. Results showed that tap to tap time, undischarged pig iron ,penetrated pig iron are the main ones.Literature studies showed that the graphite addition help to thermal shock resistance and liquid penetration(steel,pig iron) effect. In this research particle size distribution of aggregates containing andalusite and graphite determined by andreazen equation. Then different mixes with different percentage of graphite,Si, FeSi, SiC prepared by uniaxially pressing under 1500kgf/cm2 pressure by adding 4%wt novalak resin and 0.4%wt HMTA as hardner. Samples fired at 1100-1500oC under reduction atmosphere. According to specific standards density, porosity and CCS measured. Analytical tests such as XRD, SEM were carried out on sample selected from point of view of mechanical properties at different temperatures. Results showed that optimized amount of Si and Fe-Si for _-SiC formation in body is 4 and 6 %wt respectively at 1500OC. XRD and SEM analysis on sample with Fe-Si additives showed no destructive phase through the matrix, also SiC additives not only increase oxidation resistance but also no effect on thermo-mechanical properties.

Oct 1, 2011

By H. G. Ames

"The property of Perron Gold Mines, Limited, lies in the southwest corner of Pascalis township, northwestern Quebec. It is approximately 12 miles northeast of the town of Val d'Or.This ground was originally staked by Jack Mathews of Amos in the spring of 1931. Shortly after staking, a quartz vein containing visible gold was uncovered on the south boundary of the property, about 400 feet south of the present shaft. With further prospecting, another spectacular goldbearing vein was found 3,000 feet northwest of the original showing. Subsequently, several programmes of exploration were carried out in search of the main ore zone. By 1933 sufficient ore was outlined to warrant sinking a shaft. The first ore was milled in 1934.Total production from the Perron mine from commencement in 1935 to 1944 has been 317,900 oz. gold having a value of $11,935,106. The average recovery a ton for 1944 was $9.01."

Jan 1, 1954

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By Al Gagnon

Since start-up in 1972, many circuit problems have been encountered, most of which were related to the abundance of fines (-28 mesh), which the circuit had not been designed to treat. The major problems associated with the original circuit included excessive loss of magnetite, reduced throughput during periods of a high proportion of fine coal in the plant feed and low yield in the fine coal circuit. This paper outlines the coal processing circuit at Fording Coal Limited as it exists today, with emphasis on the changes to the original fine coal treatment circuit.

Jan 1, 1978

By T. M. Ahmed

Sherritt International Corporation experienced corrosion failures with the 316L stainless steel tubing in a high-pressure still condenser employed for ammonia recovery. A detailed failure analysis was conducted on the condenser tubing to determine the mode and the root cause of the failure. The analysis included both optical and scanning electron microscopy (SEM) of the inner and outer surfaces of the tube as well as characterization of the corrosion products using energy-dispersive X-ray spectroscopy (EDX). Results revealed that the corrosion attack was confined to the first ?100 mm of the tubing at the inlet where the tube was connected to the top tubesheet. The tube suffered both external stress-corrosion cracking (SCC) and crevice corrosion from the shell side (water side), and wall thinning of the inner surface (the tube side) due to erosion corrosion. It was evident that failure of one of the tubes occurred due to SCC that penetrated the whole wall thickness and resulted in a leak failure. Some prevention measures are proposed to avoid this type of corrosion attack in the future.

Jan 1, 2005

By W. H. Mathews

"The Hardie group of cinnabar claims is in the interior of British Columbia; 25 miles northwest of the city of Kamloops. It is one of a number of mercury; properties scattered along a north trending belt 20 miles long and up to 5; miles wide. In all but one of these properties cinnabar is associated with; dolomite veinlets in zones of carbonate alteration in bedded rocks of Triassic; and Cretaceous (?) age; or in intrusives cutting these bedded rocks. No dolomite alteration or cinnabar mineralization is known in the undoubted Tertiary rocks adjacent to the mercury belt.The mercury showings of the Hardie group lie for the most part in a granitic stock cutting Cretaceous (?) volcanics. The rock in this intrusive shows marked variations in texture and has been described in earlier reports as granite and granodiorice, granite porphyry, and trachyte or dacite porphyry. At Hardie mountain the cinnabar mineralization, unlike that of the other properties, is associated with a fine-grained, almost chalcedoni c, quartz; carbonates, though present, are of minor importance. Some of the most interesting showings are found in an adit in the southeastern part of the property where cinnabar mineralization shows a very distinct structural but not a genetic relationship to a brown porphyry dyke 2 to 8 feet wide cutting a phase of the stock that may best be described as aplitic"

Jan 1, 1954

By Alexander Smith

Surf Point and Edye Pass mines are on the northwestern part of Porcher island; 25 miles southwest of Prince Rupert. During the 1930's they produced about $750; 000 in gold from ore averaging better than one-half ounce a ton. The deposits are quartz veins; containing auriferous pyrite; concentrates average about 8 oz. gold a ton. The veins occur in a quartz diorite; stock. Their distribution shows an apparent control by primary flow structures; for the principal deposits lie on the axis of an arch of flow layers. The technique used in mapping the structures in the intrusive is that known as the Cloos method and described by Balk.

Jan 1, 1954

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016