Search Documents

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By J. C. Roy, S. Couture, C. Barbeau

The chemical composition of the asbestos tailings from different mines in the Eastern Townships of Quebec are fairly uniform in composition. The serpentine minerals antigorite and chrysotile form about 85 to 90 per cent of the total. Iron oxides add another 7 to 10 per cent; magnetite represents about 70 per cent of the oxides. Chromite is present in amounts of about 0.5 per cent. The average contents of elemental magnesium, iron and nickel are 23, 6 and 0.25 per cent respectively.

Jan 1, 1972

By James A. H. Church

This paper is in the nature of a protest against the dangerous propaganda afoot for the prevention of new mining undertakings and which is based on the imaginary 'blue ruin' conditions supposed to exist in the industry. An article by Mr. G. R. Pratt, A.M.E.I.C. in the first issue of the Western Canada News, February 2nd, 1925, and entitled "Review of Coal Mining in Alberta", is an excellent example of this type of propaganda. The article is a tissue of misstatements, faulty deductions and erroneous conclusions. For instance it contains the statement that some coal measures in Alberta are mined at great depth - whereas we all know that there is no coal mined at great depth anywhere in the province; another error is the classification of all mines under one head irrespective of whether they are mining prospects, 'country banks', or pukka mines equipped with railway facilities; and I believe that suppressio veri is tantamount to suggestio falsi. The bulk of his article hinges on a Table 1, which shows the details of coal produced in Alberta during 1923. Studying this table Mr. Pratt, in the manner of a conjurer producing rabbits from a hat, offers the following for the confusion of the public:- (1) "Waste effort, want of capital, waste of coal resources which result from unrestricted development"; the fact being that the waste is due to the failure of the Department of the Interior to exercise the powers which are inherent in the form of lease.

Jan 1, 1925

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By M. Mirnezami, J. A. Finch, S. Uddin

A fast, reliable and practical way of measuring zeta potential using sedimentation potential method is proposed. A cell was designed along with the instrument control software to determine the required variables simultaneously i.e. sedimentation potential, specific conductivity, volume fraction of solid as well as pH. High purity alumina and silica powders were used as test samples. Measured zeta potential using the proposed technique was comparable with the results by electrophoresis.

Jan 1, 2009

By L. Yacher

Most metallurgical plants already have sophisticated control systems as well as a process-historian that manage thousands of real-time and historical variables. There exists a huge potential for operational improvement through the inference of patterns, correlations and cause-effect relationships within these records. The ability to run online and offline advanced multivariate statistical analyses represents a great potential for the mining industry, in various areas such as cathode quality improvement in an SX/EX plant, the analysis of the correlation between the ore characteristics and the mill throughput, the determination of early failure alerts for major equipment, etc. The background theory is described, as well as some practical experiences of operations in Chile and Peru. Cu2007

Jan 1, 2007

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By D. Q. Li

"This paper briefly introduces problems that can occur in the design of rare earth separation processes and that require close attention during engineering design. Important factors must be considered include the following. 1) The separation process is primarily based on two points. One is the raw material composition and the other is the product purity requirements. 2) Optimization of the rare earth separation process requires optimization of the flowsheet configuration and each process parameter. 3) The separation of heavy rare earths is performed under non-equilibrium conditions. 4) The radioactive elements uranium and thorium must be removed from the feed to separation. 5) Process economy and environmental protection must be considered together in the evaluation of any separation technology options. INTRODUCTIONThe importance of rare earth (RE) is well recognized in high-tech applications and sophisticated national defense technologies. RE is the treasure house of the 21st Century new materials. The RE separation processes developed using HEHEHP (P507), P507-alcohol (ROH) and naphthenic acid (NA) have been widely applied in China. These processes have led to industrial production of all of the individual RE with up to 4N (99.99%) or higher purity (Li, Wan, Lin, Xie, Lin, & Wang, 1980; Li, Wang, & Xie, 1985; Li, 1995; Li, Wang, Meng, & Li, 2005). In order to achieve the best economic and environmental benefits, this paper discusses several problems to which attention must be paid in the design of rare earth separation process."

Jan 1, 2016

By M. Jarvis, D. B. Dreisinger, T. Hitchins

Mineral carbonation (MC) has been extensively researched all over the world since it was found as a natural exothermic process to permanently and safely sequester CO2. In order to accelerate the natural process, various methods for carbonation of Mg-/Ca-silicate minerals and other industrial wastes have been studied. It has been found that the MC efficiency will increase with an increase of CO2 pressure, retention time, temperature, mass ratio of Mg or Ca to Si in minerals, specific surface area, and the slurry concentration in a specific range, and with the introduction of an effective catalysts, for example, 1M NaCl and 0.64M NaHCO3 or carbonic anhydrase. However, there still is not a successful industrial application because of high economic cost and slow reaction rate. It is not economic to exploit Mg- and Ca-silicate minerals deposits or tailings to sequester CO2 by MC, due to the cost of grinding and heat pre-treatment and in some cases the whole sequestration process may result in more CO2 emissions than the amount of CO2 sequestered, due to the requirements of energy inputs. The process however, may be profitable as a whole (with carbon credits). It is suggested to combine MC with recovery of valuable metals from ore deposits in order to reduce the cost for MC by cost sharing for mineral recovery.

Jan 1, 2017

By J. Fellowes, V. Landais, J. Robson, J. Carr

"Aerospace Al-Zn-Mg-Cu (7xxx) alloys are known to be susceptible to environmentally assisted cracking (EAC). This phenomenon has been studied intensively for many decades, leading to empirically adopted methods to mitigate this problem through overaging and composition design. In parallel, many theories have been developed to explain EAC in 7xxx, but none is yet universally accepted. Today, a number of emerging techniques offer potential to shed new light on EAC in 7xxx. The purpose of the present paper is to demonstrate how X-ray tomography (XCT) combined with electron microscopy can be used to identify the true crack path in 3-dimensions, and hence identify material for site specific electron microscopy analysis. Composition mapping over large areas to high accuracy has been performed using a modern electron microprobe analysis system. This has been combined with transmission electron microscopy to investigate local composition in matrix and precipitates at high resolution. This combination of techniques across length scales offers the potential to provide new insights into the links between local composition, microstructure, and EAC resistance.INTRODUCTION Environmentally-assisted cracking (EAC) is a phenomenon which dramatically decreases the performance of metals and can cause premature failure of large structures. Observed in situations where components were not subjected to critical loads and no widespread corrosion was involved, this type of brittle failure is extremely difficult to predict. The EAC designation covers a number of phenomena, e.g. stress corrosion cracking (SCC), hydrogen embrittlement (HE), corrosion fatigue (CF), etc. Initially identified in steels, EAC can also affect other metals such as high-performance aerospace aluminium alloys, and this phenomenon has been a concern for industries for decades. Extensive research has been conducted on the effects of various environments (moist air, saline water, dry hydrogen gas, etc.) on microstructures and crack propagation, however no consensus has been reached and the exact nature of the mechanisms that control EAC is still being debated (Birnbaum & Sofronis, 1994; Gangloff, 2007; Holroyd & Scamans, 2013; Lynch, 2012; Oriani, 1972; Scamans, Alani & Swann, 1976, Young & Scully, 2002)."

Jan 1, 2018

By F. L. Casey

"Part 1 – Published Papers Baria, G., and Boshkov, S., ""Insights into Undercuttingin Block Caving"", Proc. 5th Rock Mech. Symp.,Mines Br. - Information Canada, 41-58, 1970.Barron, K., Coates, D. F., and Gyenge, M., ""ArtificialSupport of Rock Slopes'', Mines Branch ResearchReport R228, July, 1970.Barron, K., ""Criteria for Brittle Fracture Initiation inand Ultimate Failure of Rocks and Their Applicationto Fracture Zone Prediction"", Proc. 2ndCongr. Int. Soc. Rock Mech., Belgrade, 1970, 3-37.Bauer, A., and Calder, P. N., ""Projectile Penetration inRock"", Proc. 5th Rocle Mech. Symp., Mines Br. -Information Canada, 157-170, 1970.Bauer, A. M., ""Site Development and Rehabilitation ofPits and Quarries"", Canadian Mining Journal,Vol. 91, No. 7, 77, July, 1970."

Jan 1, 1971

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By J. B. Hamilton

The advantages of generating and distributing electrical energy direct from the coal-fields so closely affects the mining industry that a few remarks on the unbalanced phases of coal distribution is worthy of attention. The value of coal imported into Canada from 1912 to 1921 exceeded the sum of $580,000,000. In 1922 Ontario imported 1,640,000 tons of anthracite and 9,440,000 tons of bituminous coal. I submit that the use of Saskatchewan lignite in an electrical super-power plant equipped for the carbonizing of coal, and disposal of excess gases would be the commencement of a solution of the fuel shortage in Ontario. As Saskatchewan becomes more and more populated and manufacturing increases, the amount of by-product carbonized fuel available for shipment to Ontario will increase, and its shipment to that province would decrease the trade deficit of the national balance sheet. If and when this is carried out it will mean a better and wider market for Alberta fuels in Saskatchewan and Manitoba.

Jan 1, 1924

By M. Bourassa, P. Roy

"This paper describes the automation of Kiena's grinding circuit which comprises an open SAG mill circuit and a closed ball mill circuit with two stages of hydrocyclones. The circuit has been instrumented according to a two level control strategy.The regulatory control strategy is implemented in an industrial controller. This controller does data filtering and calculation (flowrate and solid content) and regulates the pump box levels (2), the water additions: or the pulp percent solids (4) and the fresh ore feed rate.The supervisory control calculates for the industrial controller, the fresh ore feed rate setpoint and the pulp percent solids setpoints in order to optimize the grinding circuit operation. It is made of two modules, one for data filtering and one for control optimization. The filtering program uses modern tools to adjust the measured value and estimate missing data (dynamic material balance, on line estimation of model parameter, etc.). The control program acts as an expert system which combines the benefits of model-based control and rule-based control. A multivariable predictive controller (DMC) is used to maintain the circulating load and the hydrocyclones feed percent solids (which is correlated to particle size) while the rule-based control validates the previous output, detects and avoids the SAG overloads and sump pumps overflows.The system has been operating since MAY 1992 and the benefits obtained are discussed.INTRODUCTIONIn 1990, Les Mines d'Or Kiena decided to go ahead with a project for automating its grinding circuit as proposed by the Centre de recherché minerals (CRM). Its objectives in doing so were to marginally increase production capacity (1 % ) and to create a new challenge for plant staff. The main stages of the project, which involved CRM, Kiena Mines and a consultant, are shown in Table 1. The project was completed in May 1992 with the implementation of a supervisory control system. This text describes the main features of the system with a special focus on its most innovative aspects."

Jan 1, 1993

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By J. F. Dorion

This paper presents the results of on-going investigations on the performance of support systems in Québec underground mines. The focus of these investigations is on site observations complemented by laboratory investigations. Of particular interest is deducing the corrosion rate, at selected mine sites, as determined by the installation of monitoring coupons.

May 1, 2009