Search Documents

By Kadoya H, Kondo Y

The Harima works were established in 1964 and started operation in 1966. The initial capacity was 3500 t/month of zinc and 1500 t/month of lead. Until 1990 a lot of improvements had been made and the capacity had increased 6600 t/month of zinc and 2200 t/month of lead without enlarging the furnace size. During the ten weeks campaign shut-down at the end of 1990, many modifications were carried out including the enlargement of the furnace shaft area. By these changes, the capacity has gone up to 7500 t/month of zinc and 2500 t/month of lead. In the sinter plant, the amount of SO2 rich gas supplied to the acid plant was raised to 50 000 Nm3/h from 43 500 Nm3/h. An electrostatic precipitator was adopted instead of a venturi scrubber to clean the rich gas. Oxygen enrichment has been continuously operated since August 1991, because the furnace capacity is more than the rate of sinter production. Utilisation of the sinter plant is high being as much as 97 per cent and the sulphur burning rate has been increased. In 1990 the furnace was replaced except the hearth. The shaft area was enlarged to 19.4 m2 from 15.3 m2. The target blast was designed to be more than 36 000 Nm3/h. Tuyere layout was changed to prevent slag breakouts. Due to these modifications shaft condition has been very good. Automatic launder jacket cleaners were installed to increase the lead cooling efficiency. Many other improvements and developments were also made. Coke powder injection from the tuyeres has been successfully operated since April 1987.

Jan 1, 1993

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By Forssberg KSE

The behaviour of cationic and anionic collector mixtures in the feldspar-quartz flotation system has been investigated througl conductivity, surface tension, zeta-potential and flotation studies. Tht results show the formation of molecular complexes between oppositel; charged collector ions through charge neutralisation. The molecular complexes are found to have a higher surface activity than the individua components. The mole ratio of the mixed composition is found to have, significant effect on flotation. Mole ratio less than unit} (anionic/cationic) of collector mixtures increases the flotation recoveries If the mole fraction of the anionic collector is greater than the moh fraction of cationic collector in a mixed composition, flotation ceases The flotation selectivity principally depends on the inherent differences it the surface charges of feldspar and quartz at the flotation pH values of

Jan 1, 1993

I congratulate The Australasian Institute of Mining and Metallurgy on its decision to hold its Annual Conference here in Western Australia. Western Australia, with its abundant mineral and energy resources, plays a key role in the Australian mining industry... and Western Australia will continue to figure prominently in this vital industry for many years to come. The success of our gold, iron ore, bauxite, mineral sands and other primary industries has enabled Western Australia to contribute significantly to Australia's export revenue and, therefore, to the nation's economic strength. The State's mineral wealth has also provided the impetus for a recent surge in mining related activity, including a dramatic increase in downstream processing of our raw materials. Billions of dollars worth of new project investment is either committed or awaiting final approval - and most of this new investment is a direct result of a healthy and vibrant mining industry. The North West Shelf Project - which has been providing natural gas for homes and industry in Western Australia since 1984 - has also played a key role in stimulating industrial development. The availability of abundant, competitively-priced gas from the North West Shelf has - along with the availability of other raw materials - made Western Australia a more attractive proposition for industrial investment. The company I represent, Woodside Offshore Petroleum, is operator of the North West Shelf Project on behalf of the Project's six Joint Venture Participants - Woodside Petroleum Ltd, BHP Petroleum (North West Shelf) Pty Ltd, BP Developments Australia Ltd, Chevron Asiatic Limited, Japan Australia LNG (MIMI) Pty Ltd and Shell Development (Australia) Proprietary Limited. The theme for this Annual Conference: "Excellence - the key to the continued success of the Australasian mining industry" is appropriate to the North West Shelf Project. The pursuit of excellence has been a hallmark of the Project. The Joint Venture Participants have been conscious of the need for stringent quality control at all stages of development. Procurement and purchasing policies, for instance, have demanded strict adherence by contractors and suppliers to the highest standards and specifications.

Jan 1, 1989

In late 1984, Council of the Australasian Institute of Mining and Metallurgy accepted a proposal to establish a Mineral Heritage Committee. This was to be involved in matters relating to mineral heritage-its recording, its preservation, and the acknowledgement that it can be of use to the mineral industry in the future. The Committee was established to ensure that all of the disciplines of our profession were included and that, so far as possible, all of our country as well as those countries of the Southwest Pacific Basin were represented. Some work has been commenced to bring real- isation of the importance of the heritage of our mineral industry to the forefront of the commu- nity's interest. There is not a state in this country and the Southwest Pacific where the mineral industry has not at various times proved to be the basis of community development.

Jan 1, 1987

By J Masliyah, Z Xu

The largest oil sand deposit in the world is located in Alberta, Canada, with a total proven reserve of 2.5 trillion barrels of oil. The water based extraction process is currently being used in commercial operations to recover bitumen by flotation from oil sand ores. A recognised challenge in bitumen extraction is the reduced bitumen recovery when processing ores containing high fines content or æweatheredÆ oil sand ores, collectively known as poor processing ores. Inspired by demonstrated success of using kerosene as collectors in coal flotation, an innovative idea of using oily bubbles (air bubbles coated with a thin layer of oil or solvent) was tested to improve bitumen flotation recovery from poor processing ores. In this study, dynamic contact angle of air bubbles or oily bubbles on bitumen and induction time of bitumen-oily bubble attachment in water were measured to justify the use of oily bubbles in bitumen recovery from poor processing ores. The type of oil or solvents, including kerosene, toluene and naphtha, used in generating oily bubbles showed a marginal effect on the contact angle values, similar to the values measured with air bubbles. However, the spreading of an air bubble was found to be much slower than that of oily bubbles on a bitumen surface. The induction time for oily bubble-bitumen attachment was found to be much shorter than that for corresponding air bubble-bitumen attachment in the process water from poor processing ores. The reduced induction time for kerosene-coated air bubble-bitumen attachment correlates well with the improved bitumen recovery from poor processing ores using kerosene-coated oily bubble flotation technology.

Jan 1, 2005

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By Richards JR, Herbert HK

A basic question in preparing this review was how to define sulphur mineral occurrences as being associated with the Pacific Rim. This question will be reconsidered later. The isotope composition of sulphur- containing minerals may be considered in terms of two primary sources - 1. deep- seated sulphur, devoid of crustal contam- ination with a 634S value near 00/0o and 2. oceanic sulphate which fluctuated in value between +10 and +300/00 over geological time (Claypool et al., 1980). However, minerals have seldom been directly derived from these primary sources as even evaporites have been dissolved and reprecipitated. The marine source is differentiated biochemically and isotopically in recent sediments where sulphide from bacterial sulphate reduction may be significantly depleted in 31S. The question of chemical interaction of ascend- ing magma with upper crustal rocks has become one of degree rather than whether or not it occurs. Mineral deposition is considered increasingly in terms of mixing of fluids and their chemical reactions with rocks rather than direct precipitation from magmas or hydrothermal fluids derived from them.

Jan 1, 1987

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By Knijnikov M, Cameron D

Coal Quality management and the control of the flow of coal through complex mining preparation and transport phases of standard mining operations has assumed greater importance over recent years.

Jan 1, 1998

By Hayba DO

Metal-rich slurries discharged from excess-enthalpy geothermal wells at Kawerau (NZ) indicate that an efficient ore precipitation mechanism operates in some feedzones. In our conceptual model, which takes into account the relative permeabilities of liquid and gas phases in boiling fluids, a metal-precipitating liquid phase is effectively immobilised along boiling fronts, leading to the formation of highly concentrated ore. Chemical equilibrium and heat/mass transport modeling demonstrate the general applicability of this conceptual model to hydrothermal eruption environments.

Jan 1, 1995

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

By Campbell J

After eighteen months of discussions with employees and their trade unions, multiskilling was introduced at the Hellyer concentrator in early 1989, coinciding with the plant commissioning. Multiskilling was introduced with the Hellyer Skills Acquisition Program together with intensive training and performance assessment. Design innovations have helped to improve productivity. There have been some difficult times with personnel tending to return to the old and traditional ways of operating. In general, these have been overcome to ensure the success of multiskilling at Hellyer. The main factors making multiskilling effective have been continual training and assessment, and a competent team of shift supervisors. This has improved work standards towards the high level expected from a multiskilled approach without compromising safety standards.

Jan 1, 1991

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

By Boyd G. L

Stress measurement is at the core of most stability design analyses. It is demonstrated that contrary to accepted practice, it is the field measurement, and not the calculated prediction, of stress that requires most examination and review. Since it is not really possible to quantify rockmass properties, the stiffness values used in reduction of stress measurements and in subsequent design analyses (either empirical or numerical modelling) must consider an appropriate range of values.

Jan 1, 1995

By LaBrooy SR

A number of gold processing plants in Western Australia have nickel in their ores, leading to significant levels of nickel on their loaded carbon. The presence of nickel during leaching, adsorption and elution'may have detrimental effects on cyanide consumption, carbon inventory requirements, stripping costs, electrowinning efficiencies and may contaminate the gold bullion.This paper discusses the competitive adsorption of gold and nickel cyanides onto activated carbon and investigates changes in solution parameters that may improve gold adsorption and/or inhibit nickel adsorotion.

Jan 1, 1997

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997