Search Documents

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011

By W D. Rech, K W. Keskimaki

As an integral part of the conversion from rail haulage to conveyor haulage at Henderson, over six kilometres of drifting and several large complex openings were mined. The deepest of these areas was nearly two kilometres beneath the surface, bringing all of the challenges of rock stress and heat that come with mining at these depths. Though many mines operate at these depths, the development of the infrastructure necessary to support a 36 000 tonne per day caving operation brought some unique challenges to the development mining activity. The issues handled include: finding experienced staff for a æfast trackÆ development program; rock bursts and ground conditions; inflow of 50 degree centigrade water; acceleration of the project completion; large diameter raise boring and difficult muck handling.

Jan 1, 2000

By C McCamley

"The requisite for maintaining optimal carbon concentration levels in a carbon-in-leach (CIL) circuit is of paramount importance in the prevention of gold losses. The process’s ability to recover gold from the aqueous phase is primarily dependent on the carbon loading profile of the CIL train.Newmont Boddington Gold (NBG) have over 2015 tested the Mintek online carbon concentration wmeter (C2 Meter) suitability for effective carbon concentration measurements in their CIL circuit compared to the standard method where the readings are taken twice a shift by the operations staff. The C2 meter works by passing a 1MHz ultrasonic signal through a slurry containing carbon where there is a relationship between the carbon concentration and the attenuation of that signal.It also highlighted another area where the C2 meter could be implemented at NBG whereby the instrument can be as a cautionary device for carbon losses in place of carbon safety screens.Citation:McCamley, C, 2016. Continuous Carbon Concentration Measurement at Newmont Boddington Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 207–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By B Chapman, R Nievergelt, J Hill

A major component of Sydney’s new South West Rail Link project is the Hume Highway Underpass (HHU), an 80 m long twin track mined tunnel excavated at a depth of just 5 m below the pavement of the Hume Highway; one of Australia’s busiest road corridors.In order to ensure a safe and efficient construction of the underpass without disruption to the Hume Highway traffic, design of the HHU required specific focus on the prediction and control of ground movements. This paper describes the design and construction solutions adopted in response to these challenging constraints. The paper also provides discussion on the observed behaviour of the underpass during construction and the results of a back analysis that was undertaken during construction.CITATION:Hill, J, Nievergelt, R and Chapman, B, 2014. Design and construction of Sydney’s South West Rail Link Hume Highway Underpass, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 375–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Hobbs

Mining is experiencing a difficult period of low profitability and declining productivity. To achieve sustainability, mining companies are challenged with improving output, quality and safety while decreasing costs. At the same time, organisations are having to manage a workforce in which individuals no longer accept a traditional style of management, employees prefer more flexible employment, and diversity within teams is becoming the expected norm.Increasing organisational diversity has been shown to have a positive impact on performance and therefore sustainability. Gender diversity and equality between working men and women is the area most studied in this regard. Executives are becoming more aware of the correlation between gender diversity and performance with some larger organisations having dedicated resources to increase the number and status of women in their organisations. Despite this, limited improvement in gender equality is apparent globally over the last decade with some industries, including mining, going backwards. So why is this the case and what other strategies are available?In 2015, the United Nations Women National Committee Australia (UN Women NCA) in conjunction with Autopia released a white paper discussing the lack of visible change in gender equality despite the widespread implementation of merit-based personnel management strategies. Using research from around the world and thoughts from influential government, education and business leaders, the paper ‘Rethinking Merit’ debunks the myth of the meritocracy. It provides a number of recommendations for organisations committed to improving their performance and sustainability through diversity, including a variety of real-life company examples, instead of relying solely on merit-based decision-making.This paper takes the recommendations of ‘Rethinking Merit’ and applies them to the mining industry. It shows the relevance that rethinking merit has for the industry and why applying the recommendations can result in an increase in diversity, therefore enabling greater performance and sustainability of mining companies. This paper provides case studies from Aurizon, Iluka Resources and BHP Billiton and, as a guide for managers, a generic diversity strategy designed to be implemented alongside traditional merit-based personnel management techniques.CITATION:Hobbs, K, 2016. Rethinking merit for a sustainable mining industry, in Proceedings International Mine Management Conference, pp 139-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By B Besa

Australia is a world leader in the design and operation of mines accessed by the decline method. Literature indicates that a number of metalliferous underground mines using the decline system are also increasing steadily. This increase has generated a great deal of interest in underground haulage systems in future due to the huge costs involved in the development of declines. Studies have also shown that the current method of accessing orebodies by the conventional decline method has proved to be expensive, especially for narrow vein deposits. This is because decline development costs are influenced by mine planning and design parameters as well as available haulage systems that the mining engineer can choose from. The current access method suggests that more waste material is being extracted because of the size of decline openings adopted (5.5 mW and 5.5 mH). Also the conventional 1:7 decline gradient and turning radius of 20 m makes decline lengths, as well as the duration of development, excessively longer. This paper discusses results of a mine design case study with monorail technology as a method of accessing and developing the decline. The proposed system is economical, has high advance rates and offers a significant reduction in capital expenditure. The study compares costs, development metres and the duration of decline development using the monorail system with the conventional (truck haulage) access method. Results obtained indicate that the monorail technology has the potential to reduce the decline length by over 62.6 per cent and decline costs by 63 per cent for the case study. The monorail system also reduces the total capital development costs by 22 per cent for the same case study. Due to rapid development resulting from increased advance rates and the shorter decline length coupled with smaller decline openings, the time to access the deposit reduced by 71.8 per cent. This case study demonstrates that the economics of narrow vein deposits can be improved significantly by using the monorail system of decline development.

Jan 1, 2008

By R Burke, G Ramage, C Donnelly

Over the decades, Redpath has undertaken a multitude of tunnelling and underground excavation projects for civil and mining clients both domestically and internationally. These projects have been undertaken through varying strata conditions with differing excavation methods in remote locations and in central business districts.With the recent turbulent nature of the global financial environment, project drivers have been challenged with the emphasis being placed on methods to gain early access to orebodies, rapid development techniques, lower capital costs and reduced labour requirements to name a few.A number of mining companies seeking to achieve these objectives have commenced the journey to better understand the operational constraints, challenges and opportunities that may be available with the use of alternative excavation methods.The development of safe and effective alternative excavation methods that comply with both domestic and international mining legislation and regulatory requirements is a challenge the industry needs to embrace. Given the current cost pressures being faced by the Australian mining industry, some alternative excavation methods offer the potential for longer term sustainability and rapid development of resources.More recently work has been undertaken on a project that challenged the norm and implemented an alternative excavation method with the use of an excavator with a rotating drum cutter head.This paper will review this recent project and provide technical and operational insight into some of the challenges faced in implementing an alternative excavation method in the metalliferous industry.CITATION:Donnelly, C, Ramage, G and Burke, R, 2014. Challenging the norm – alternative excavation method in mining, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 187–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Traditional in situ fan flow test methods under accepted standards require determinations to be made of both static pressures and total pressures during testing. This is to determine the resultant velocity pressures, which are vital in the accurate determination of the final fan airflow. These crucial velocity pressure (Vp) determinations are normally determined using simple manometric instrumentation such as an electronic manometer or an inclined liquid filled manometer. There is relatively little noise or fluctuation in the static pressure determinations and they can be quite easily and accurately recorded. There is almost always considerable fluctuation in the velocity pressure determinations though due to the highly turbulent and irregular velocity profile normally found in such in situ installations. This velocity turbulence means that the recording of such data is subject to random human error as the observer tries to average such fluctuations mentally during the observation period. Worse than this, and in the extreme, the recording of such velocity pressure data could actually easily be misreported if, for some reason, persons chose to do so.The author has devised a field method using highly accurate quartz crystal logging barometers to objectively record these velocity pressures. The method eliminates the ability to either mistakenly or intentionally misreport these crucial velocity pressures and is carried out in parallel with the recognised methodology, so result comparisons can be drawn. As such, a far greater level of confidence can be achieved in the final flow performance results than using the traditional more subjective method. Further to this it is difficult and almost impossible to refute the results using this ancillary substantiation method.The accurate determination of fan flows due to the impost of the carbon tax has taken on much more significance given the financial impacts in Australia at this time. The methodology detailed herein can be applied equally for both fan flow compliance testing and the verification of mine airflow data for greenhouse gas emission evaluations.The paper utilises the results of one 24-point pitot traverse to demonstrate the various findings. These include the very wide range of velocity pressures, which were logged at most of the measuring stations. It also illustrates how the method is utilised and compares the results derived from both this method and the more subjective traditional method along with the benefits of logging the velocity pressure results during the testing process.CITATION:Rowland, J A, 2013. Removing some subjectivity from traditional BS 848 and ISO 5802 in situ fan flow tests, in Proceedings The Australian Mine Ventilation Conference , pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By T Purvis, J Calverd, A-K Greve

The Ernest Henry Mining (EHM) underground mine is situated adjacent to the Great Artesian Basin in North Queensland and within a fracture zone. Underground development commenced in February 2008 and has extended to approximately 1000 vertical metres below the surface.Groundwater has been encountered in numerous locations throughout the mine, predominantly on the eastern side of the orebody and often related to fault structures. Most of the groundwater encountered has been managed with conventional pumping systems; however, on occasions large water inflows have been encountered, which have had a significant impact on the planned development of the mine. Some of the intersections encountered had the potential to compromise the mine from a combination of high temperature (over 45°C), high pressure (3500 kPa) and high flows (50–100 L/s).This paper describes three case studies where significant water inflows were encountered and then controlled by the injection of cementitious grout into the rock mass. The case studies are the 1650 mid-shaft heading, the 1325 shaft access decline and the 1625 to 1475 fresh air rise (FAR) raise bore. Each case study includes a brief description of the event that occurred and the grouting equipment and techniques developed to enable mining to continue.The paper also describes the development of a hydrogeological map of the mine, the probe-hole regime used for high-risk headings and the required processes and systems to inject both cementitious grouts and polyurethane resin into the rock mass.CITATION:Purvis, T, Calverd, J and Greve, A-K, 2014. Management of high-pressure groundwater in underground development at Ernest Henry Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 217–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R Shaw, R Williamson

Global iron ore demand, sparked by ChinaÆs rapid industrialisation and emergence as the worldÆs newest steel market, has seen iron ore groups investing heavily in production capacity as well as infrastructure. The success of these new projects depends heavily on reliability, competitiveness and quality control in an increasingly demanding trading environment. Furthermore, the iron ore industry continues to improve its competitiveness in mining practices, technology innovation and management processes. The continued fine tuning of these sectors will be critical to the success of the industry in the years ahead, and this mining sector will continue to demand process improvements from their service suppliers to maintain competitiveness. Automation offers a real solution to these demands. A crucial quality control element in mining, beneficiation, stockpiling and shipping stages is ensuring representative samples of ore are taken along each step of the process. When these samples reach the laboratory it is imperative that the sample is representative of the entire stream and that no induced errors occur. Examples of automation start with mechanical primary and secondary samplers in the run-of-mine processes through to sample tower and laboratory crushers, dividers and collectors. Automation is widely used in many forms to provide reliable and repeatable samples for analysis whilst providing a safer working environment. Laboratory automation systems in use today vary from simple linear systems to sophisticated robotic cells. Sample automation in the iron ore industry has resulted in many benefits for both producers and their customers. The most significant benefits have come in the form of higher safety standards whilst reducing sample error, sample handling and sample contamination during collection. These benefits have been further augmented by reliability and repeatability of automating the final sample preparation and analysis stage. Today these benefits are reflected in reduced costs of sampling and improvement in both turnaround time and quality of results, whilst complying with Australian safety and ISO sampling standards.

Jan 1, 2007

By B Belle

In a deep, gassy predrained coalmine, ventilation and goaf drainage systems act as critical controls to manage longwall (LW) panel return gas levels. The goaf capture efficiency of most LW panels ranges from 45 to 85 per cent based on the gas domain at respective workings. Recent operational experiences have indicated that 50 m goaf hole spacing is optimal for management of high production retreat gassy LW panels, where the probability of goaf hole failures are frequent. Due to the horizontal stress direction geotechnical issues, goaf hole failure just behind the LW face is a recurring challenge resulting in significant and immediate increases in LW panel return gas levels. This paper presents a successful implementation of an innovative LW tailgate (TG) road cut through seal goaf fan/venturi system. The system incorporated a 17' (400 mm cased) hole drilled to 320 m deep in a perimeter roadway on a retreating LW TG road drawing the working seam horizon goaf gas behind the perimeter of seals. The surface goaf fan/venturi system was aimed to safely exhaust the LW deep goaf gas and thus withhold the goaf stream spillage to TG drive area and reduce the panel gas load by controlled operation of the system using continuous monitoring of CH4, CO and O2 levels. This control philosophy was made operational without impacting the use of the perimeter inbye ventilation shaft used for mine cooling and providing additional ventilation dilution capacity. The instantaneous reduction in TG gas levels of up to 0.3 per cent was observed even when the LW was 300 m away from the c/t seal goaf hole. Success of this concept TG seal goaf gas control system used even when the LW was 1300 m outbye has become an inventory of additional control for future deep and long LW blocks. This paper attempts to share the design process in addressing other risks and desired outcomes in managing the LW gas levels.CITATION:Belle, B, 2015. Innovative tailgate mobile goaf gas management in two gate road longwall panels – concept to implementation, in Proceedings The Australian Mine Ventilation Conference, pp 31–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By R Young

Independent Project Analysis (IPA) is in the business of benchmarking the performance of capital projects on behalf of owner companies in the processing and extractive industries. IPA assesses between 500 and 800 projects each year. The projects are conducted globally and range in size from about $1 million to over $30 billion. Using the data, we are able to benchmark the performance of Australian projects against the rest of the world. This presentation focuses on the performance of large (greater than $100 million) projects that involve chemical or thermal processing.We regularly hear calls for more processing to be conducted in Australia but on the other hand industry leaders are concerned about the poor success rate of solids processing projects in Australia. Data gathered by IPA indicates that there is good reason for the concern. Out of a sample of 31 large processing projects conducted in Australia, 23, or 74 percent, were classed as failures. This performance is significantly worse than for similar projects in other parts of the world. The presentation analyses why the performance is worse and demonstrates that many of the reasons behind the failures were manageable by the project team. Furthermore, members of the project teams on at least half the failed projects knew that the projects were on a path to failure before the project was authorised but could not be heard.The presentation discusses how large projects that involve process design and, in many cases, new technology, need to be set up for success. *This is an abstract only. No paper was prepared for this abstract.*

Aug 8, 2011

By Ushakov S

New geological and geophysical in vestigation including our detailed field observation in different regions of the Koryak upland testify that Nor- theastern Eurasia margin eastward of the Ochotsk-Chukotka belt is composed of a collage of allochtonous terranes arcs and sedimentary filling of back- arc basins, which bordered North East Siberia and Chukotka (1)1). Ancient island are assemblages are the most tipical for this region (2-4; shown by heavy line). They are marked by long (500-1000 km) volcanic belts which become younger towards the Pacific up the Latest Jurassic-Neocomi- an (2) to Late Cretaceous (3) and Pale- Gene (4).

Jan 1, 1987

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By J B Tucker, A T. McGrath

Situated in north-west Queensland, Australia, the Ernest Henry Mine (EHM) has been producing copper and gold since 1996. Owned and operated by Glencore Xstrata, ore is currently sourced from a newly developed underground sublevel cave (SLC) mine below the old EHM open pit (the pit). Ore feed to the concentrator is supplemented by satellite open pits comprising the Mount Margaret operation.The transition from open pit to a producing underground mine involved a complex extraction sequence for the first two production sublevels on RL1650 and RL1625. Underground mining during cave initiation was further complicated when south wall instability prevented completion of the final open pit shell. The transition mining phase included mass firing of an inclined crown pillar between the initial SLC void and the pit followed by a combination of transverse and longitudinal SLC mining.The inclined crown pillar mass firing was the first significant milestone in the extraction of the transition ore block. Comprising approximately 890 000 t of in situ material; 70 000 m of drilling was charged with 351 t of emulsion and 6026 electronic detonators to initiate the single mass firing. The firing contained five direction changes over 19 seconds making it one of the largest and most complex underground blasts ever conducted in Australia.Risk management was integrated into every facet of the technical and operational planning and execution of the transition mining phase, whilst maintaining daily mine construction and production commitments. This paper provides a detailed overview of the transition objectives and constraints, mining method selection, post mass blast outcomes and the journey ahead.CITATION:McGrath, A T, Campbell, A D and Tucker, J B, 2014. Transition of the Ernest Henry Mine from open pit to an underground sublevel cave, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 297–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By V Gumba, S Narendranathan, C Barker, R D. H Thomas, G P. Bungard

This paper presents the positive outcomes on an EPCM project, which was undertaken in a challenging environment, whereby the design team had to generate a design with a number of stringent serviceability criteria, any deviation from which would have had significant implications to the proposed design performance. The success of the design implementation within the tight time frame hinged upon the precise installation by a skilled contractor. The overall objective was achieved as a result of close collaboration between the designer and contractor ensuring all stringent quality assurance/quality control (QA/QC) aspects were met and opportunities to optimise design without compromising on performance were identified and implemented, resulting in a cost saving of over A$13 M.CITATION:Narendranathan, S, Thomas, R D H, Bungard, G P, Gumba, V and Barker, C, 2012. The importance of collaboration between designers and contractors in implementing a design in challenging conditions, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 97-102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014