Search Documents

By Antti J. Perala, Teemu J. Yli-Kovero

"Efficient use of land is constantly requiring more underground construction. Minimized execution time and disturbance to surroundings and nearby structures are essential benefits for all construction techniques. To meet the demands of a modern construction project, suppliers have to be able to provide high-quality and tailor-made products just on time. RD pile wall is a retaining wall based on drilled steel pipe piles which are connected to each other with special interlocking profiles. RD pile wall is a solution which enables penetration of overburden soil, dense fill layers including stones and boulders, and embedding into the bedrock in one single operation. Several test installations and laboratory tests have been made to develop the system and to test and improve the water tightness of the wall. Beside these tests, RD pile wall has also proven its reliability in almost 70 projects. Largest project so far has been Pasila Tripla project in Helsinki, Finland. A permanent retaining wall with surface area of 18,000 m2 (193,750 ft2), excavation depth of 21 m (68 ft) and over 17 m (56 ft) of water pressure was made with 711 mm (28”) and 406.4 mm (16”) pile sizes. Piles were delivered to site in one piece with lengths up to 33.5 m (110 ft).INTRODUCTIONExcavations in cramped city centers and in between of existing buildings and other structures are facing more and more challenges. Installation of sheet pile walls is often problematic or even impossible due to obstacles in ground from old structures and due to demand to extend the excavations to even deeper and harder soil layers. Also installations of secant pile walls are facing difficulties due to cramped construction sites and constantly tightening execution times.On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid- 1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall, was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers).PRINCIPLE AND MAIN BENEFITS OF THE METHODRD pile walls can be used in all soil conditions. Most beneficial the system is in extremely demanding soil conditions where the installation of traditional retaining walls is challenging or even impossible. The RD pile wall is a combination of drilled steel pipe piles and interlocking sections as shown in Fig. 1.Individual RD piles are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole (DTH) hammer using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings shown in Fig. 2."

Jan 1, 2017

By Met M. E

In choosing the subject for my address to you this evening I was actuated by the knowledge that in the past Australian metallurgical problems have been solved by the introduction of extremely interesting processes. Frequently such processes originated in this country, or at least were first adopted here on a large scale.Chronologically there comes to mind the application of chlorination to the Mount Morgan ores from 1888 onwards.Then the application of pyritic smelting to the Mount Lyell ore body in 1896, followed closely by the successful flotation of zinc blendÇ! at Broken Hill, about 1900, and the treatment of the refractory Kalgoorlie gold ores by roasting and cyaniding. With the development of the differential flotation process at Broken Hill came the production of a slime lead concentrate carrying zinc which necessitated the use of a high zinc slag in the lead smelting process. Although previously considered impossible, the necessarytechnique was successfully evolved at Port Pirie resulting in the accumulation of large tonnages of zinc-bearing slag as potential sources of that metal. The past twenty years have witnessed:-(a) The establishment of a flourishing iron and steel industry, with its attendant coking and by-product plant at two centres in New South Wales, namely, Newcastle and Port Kembla.(b) The establishment of an electrolytic zinc process at Risdon in Tasmania.*Presidential Address, Melbourne, 20th August, 1936.

Jan 1, 1936

By . Jaime G Tapia Aguirre

La Unidad Minera Rosaura del Grupo Glencore fue considerada la mina subterránea más segura del país durante los años 2005, 2006 y 2007. Sin embargo, cuando el Grupo Glencore adquirió la concesión de Rosaura, el panorama minero era de una mina marginal, de bajas leyes. Por esta razón, el único metodo a ejecutar para hacer de Rosaura una mina rentable era el de utilizar un método masivo. Em ese semtido, el presente texto señala la operación de mina cone el análisis y conocimiento de causa raíz en la prevención de caída de roca.

Sep 12, 2011

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By F. Baerhold, S. Mitterecker

"Acid recovery is an important process step in pickling and leaching processes. Pyrohydrolysis in spray roasters and fluidized beds is a well-established technology to recover hydrochloric acid, but the hydrolysis in the liquid phase is more and more considered as an alternative new process route. The characteristic features of these three processes will be discussed along with select industry trends. For example, hydrochloric acid based leaching processes for ilmenite and nickel laterite ores produce far larger volumes of waste acid streams than the steel industry. Scaling-up of the spray roasting technology to the highest possible capacity is necessary in order to become more cost effective. In addition, process routes based on ferric chloride pyrohydrolysis allow the production of super-azeotropic HCl (up to 30 wt.%). Finally, the new ECOmode concept optimizes the operation of both pickling lines and the spray roast acid recovery plant. Long term results from industrial applications show that fuel savings in the spray roaster of 25% are easily achieved without additional process steps. An attractive feature is also to upgrade existing installations to higher plant capacities.INTRODUCTION Pyrohydrolysis is the conversion of metal halides into metal oxides at elevated temperatures in the presence of water vapor. Reaction products are a hydrogen halide gas and a metal oxide. The process was originally developed and introduced into the market by ANDRITZ Ruthner in the 1960’s. It has found wide technical application in the field of acid recovery and oxide production. The introduction of this process has revolutionized pickling technology. The use of hydrochloric acid has strongly increased over the last decades, since pyrohydrolysis is available for the total recovery of waste pickle liquors from mild steel pickling, as illustrated in Figure 1.Chloride media are also used increasingly in the metallurgical industry. Oxide production processes for Mg, Co, Ni, and Al have been installed. Processes using hydrochloric acid are known for the leaching of ores as well as for the re-extraction of metals from organic solvents. In both cases the recycling of HCl is of substantial importance to achieve highly economic processes and to reduce waste."

Jan 1, 2016

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

By J. C. Borland, J. H. Rogerson

Jan 1, 1963

By S. Krukowski

Iodine is a bluish-black, crystalline solid with sub-metallic luster, and has a specific gravity of 4.93. It volatilizes (sublimates) at ordinary temperatures into a blue-violet gas that has an irritating odor. Iodine is the least active of the halogens, all of which readily displace it. Only slightly soluble in water, iodine also dissolves in carbon disulfide, carbon tetrachloride and chloroform, giving a deep violet solution. The primary sources for iodine production are sub-surface brines associated with petroleum and natural gas deposits, and as a byproduct from nitrate deposits in Chilean desert caliche. The largest source of iodine is seawater which contains 0.05 ppm, or about 31 Mt (34 million st). Seaweed of the family Laminaria can extract and accumulate up to 0.45 percent iodine on a dry basis. Seaweed was an important source of iodine prior to 1959. However, it remains a significant source of iodine in the diets of many populations throughout the world.

Jan 1, 2005

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

In, one stage of the purification sequence of the zinc sulphate electrolyte used at Risdon, cobalt is, precipitated as cobalt nitroso-,B-naphtholate, which is separated from the solution by filtration. Owing to the method of conducting the purification the filter cake contains much gypsum, unconsumed calcium hydroxide, basic zinc sulphate, and entrained zinc sulphate solution, Small amounts of iron and copper that have escaped previous purification steps are also precipitated with the cobalt as nitroso-,B-naphtholate. Thisprecipitate, normally carrying about 18% cobalt, is the raw material for the production of cobalt oxide, cobalt sulphate and cobalt metal.COBALT OXIDEThe main problem in the preparation of a reasonable grade of cobalt oxide from the filter cake is the economic separation ,of the cobalt nitroso-,B-naphtholate from the gypsum. This was solved by the application of flotation. It was discovered that the cobalt nitroso-,B-naphtholate, under correct conditions, would float without any addition agent, giving a relatively high grade concentrate. A plant, was built and has been in operation since 1936. The filter cake is pulped with water and pumped to one of two mechanically agitated tanks, eath capable of holding one day's output. Sulphuric acid is added until the free acid concentration reaches about 3 gm. per litre. Basic zinc sulphate is dissolved and calcium hydroxide converted to gypsum. The pulp, carrying about 2t lb. of solids per gallon, is pumped at a suitable rate to the first of a series of 10 flotation, boxes.. Each box is 3 ft. by 2 ft. 9 in. by 5 ft. deep, and, all have a common, pulp level, since the...

Jan 1, 1949