Search Documents

By Jean Igor Margem., Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Sergio Neves Monteiro, Artur Camposo Pereira, Rômulo Leite Loiola

"The fibers extracted from the stem of the bamboo plant have been investigated as possible reinforcement composites due to their relatively high tensile strength. Although previous works have already been conducted about the mechanical properties, up to now a dimensional characterization of the distribution and the effect of diameter on the elastic modulus of bamboo fiber of the specimen dendrocalmus giganteus has not been performed. The aim of the present work was to statistically characterize the distribution of the diameter of a lot of bamboo fibers of that specimen. Based on this characterization, diameter intervals were set and the dependence of the Elastic Modulus (E) of theses fibers with a corresponding diameter was analyzed by the Weibull Method. The results indicated an inverse dependence, in which the highest Elastic Modulus were obtained for the thinnest fibers. Moreover, it was found that a mathematical hyperbolic relationship fit well this inverse correlation between the Elastic Modulus and the bamboo fibers diameters.IntroductionBamboo is a well known grass-type plant with a hard and stiff stem or culm that can reach, in some species, more than 10 cm in cross section diameter and stand several meters height. Owing to its low density, approximately 0.9 g/cm3, bamboo culms have been used in house construction from scaffoldings to panels. As an abundant natural resource in tropical and temperate regions, specially in Asia and South America, bamboo is also a substitute for wood and plastics in furniture and lightweight parts of automobile [1,2]. The cylindrical shape of the culm is, however, a limitation for its direct use in engineering systems. Consequently, research works have been conducted on bamboo fibers stripped off from the culm as reinforcement of polymer composites. [1-12]. According to Shin et al [3] bamboo fiber-epoxy laminates can be made into specific sizes and shapes, preserving the natural microstructural properties. These fiber composites overcome the limitation of the culm's cylindrical macrostructure. As a further advantage, Shin et al [3] indicated that cracking and bioerosion caused by insect pests is prevented."

Jan 1, 2013

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By Gjergj Dodbiba, Toyohisa Fujita, Takahiro Kikuchi, I-Chen Wu

"In order to separate molybdenum (Mo) from the high-level radioactive liquid waste (HLLW), Pb-Fe based adsorbents were synthesized. The adsorbents were precipitated by adding sodium hydroxide in mixture of 1 mol/L lead nitrate and 1 mol/L ferric nitrate aqueous solutions. Each precipitate was then filtered, dried and ground to obtain a fine powder, which has been used as an adsorbent. Two main parameters were considered when synthesizing the adsorbents, i.e. the pH value at precipitation of adsorbent precursor and the calcination temperature of Pb-Fe based adsorbent. Moreover, the structures of the synthesized adsorbents were investigated by means of an X-ray diffractometer.The experimental results indicated that the calcination temperature of the Pb-Fe based adsorbent has a great influence on adsorption capacity of the adsorbent for Mo. It was found that when the Pb-Fe based adsorbent was calcinated at 500 oC, the sorbed concentration of Mo was the highest.1. IntroductionThe high-level radioactive liquid waste (HLLW), arising from the reprocessing of nuclear fuel are generally immobilized in an alkali borosilicate glass matrix. Broadly speaking, alkali borosilicate glasses are the matrix of choice for the immobilization of the HLLW, since they permit vitrification of waste stream of variable composition, [1]. Within this frame, the incorporation of molybdenum (Mo) is of particular interest in the vitrification of HLLW. Molybdenum is know to have a low solubility in borosilicate glass compositions and its presence in excess results in the phase separation of a complex yellow molten salt during vitrification, [1]. The formation of so-called “yellow phase” material during the vitrification process is undesirable since it leads to the accelerated corrosion of the inconel crucible liners. Furthermore, the “yellow phase”, which is reported to contain also other fission products, is soluble in aqueous solution providing a potential route for the leaching of radionuclides from the vitrified waste, should it come into contact with water, [1]."

Jan 1, 2008

By Christian Ludwig, Virginie Silberstein, Rizlan Bernier-Latmani, Simona Regenspurg

"Residues from waste incineration (bottom ashes) form large amounts of heavy metal-rich waste. Theoretically, heating and the addition of chloride to the ashes could remove these metals by formation of volatile metal chlorides. The remaining heavy metal-poor ashes could be used, for example, as cement additives. In the proposed process of our study we used bypass dust from the cement industry as chloride additives to the bottom ashes. We aim to determine experimentally the optimal conditions to remove heavy metals from ashes and to simulate this process by thermo- chemical modeling. In our experiment we investigate heavy metal flows by heating of differently composed mixtures of bottoms ash and bypass dust in dependence of different furnace temperatures (500-1200 °C). Furthermore, we investigate the reactivity (leaching characteristic) of the resulting product in order to predict if secondary residues can be landfilled in agreement to Swiss regulations for inert materials.IntroductionThe incineration of garbage is generally considered as the most environmentally friendly method for the reduction of municipal solid waste. This is because, compared to traditional storage of waste on landfills, incineration produces less greenhouse gases and destroys toxic organic compounds. The released exothermic energy can be recuperated and the residues from the combustion chamber (bottom ash) are strongly reduced in volume. However, they still form about 600 kt of waste per year in Switzerland, which needs to be landfilled. However, these residues could be potentially used as construction materials after mechanically recovering ferrous and non-ferrous metals. However, the resulting ashes (discharged dry or wet) still contain increased amount of heavy metals (exceeding state regulation) requiring them to be finally deposed on a hazardous waste site. A thermal treatment of these ashes could enable both, to separate and recuperate the remaining heavy metals and an inorganic heavy-metal poor material. The evaporation of metals depends on temperature and can be lowered by addition of chlorides, which would lower the boiling point of most metals by formation of metal chlorides (table 1). 745"

Jan 1, 2008

By Christian Ludwig, Virginie Silberstein, Rizlan Bernier-Latmani, Simona Regenspurg

"Residues from waste incineration (bottom ashes) form large amounts of heavy metal-rich waste. Theoretically, heating and the addition of chloride to the ashes could remove these metals by formation of volatile metal chlorides. The remaining heavy metal-poor ashes could be used, for example, as cement additives. In the proposed process of our study we used bypass dust from the cement industry as chloride additives to the bottom ashes. We aim to determine experimentally the optimal conditions to remove heavy metals from ashes and to simulate this process by thermo- chemical modeling. In our experiment we investigate heavy metal flows by heating of differently composed mixtures of bottoms ash and bypass dust in dependence of different furnace temperatures (500-1200 °C). Furthermore, we investigate the reactivity (leaching characteristic) of the resulting product in order to predict if secondary residues can be landfilled in agreement to Swiss regulations for inert materials.IntroductionThe incineration of garbage is generally considered as the most environmentally friendly method for the reduction of municipal solid waste. This is because, compared to traditional storage of waste on landfills, incineration produces less greenhouse gases and destroys toxic organic compounds. The released exothermic energy can be recuperated and the residues from the combustion chamber (bottom ash) are strongly reduced in volume. However, they still form about 600 kt of waste per year in Switzerland, which needs to be landfilled. However, these residues could be potentially used as construction materials after mechanically recovering ferrous and non-ferrous metals. However, the resulting ashes (discharged dry or wet) still contain increased amount of heavy metals (exceeding state regulation) requiring them to be finally deposed on a hazardous waste site. A thermal treatment of these ashes could enable both, to separate and recuperate the remaining heavy metals and an inorganic heavy-metal poor material. The evaporation of metals depends on temperature and can be lowered by addition of chlorides, which would lower the boiling point of most metals by formation of metal chlorides (table 1)."

Jan 1, 2008

By Kouji Mimura, Masahito Uchikoshi, Minoru Isshiki

"HfO2 is expected to be a gate dielectric used in ULSI alternatives to S1O2. Although the materials used in ULSI are required to be significantly pure, commercial Hf contains > 2 mass% Zr. It is important to establish a process for removing Zr from Hf. In the present study, anion-exchange separation using a multi-column method was employed. The separation tests were carried out at variety of temperatures and flow rates. The decrease in the flow rate of the mobile phase made the elution curves of both Hf(IV) and Zr(IV) broaden contrary to the case of Co(II), Cu(II), or Fe(III). This is caused by the difference in adsorption rate on the anion exchange resin. In addition, more than one column was connected in series in order to enhance the separation. As a result, the content of Zr(IV) was successfully reduced to 1/100 of that relative to the raw material.IntroductionHafnium is one of the most important materials in modem society. The main applications of Hf metal are as a control rod in a nuclear reactors because of its large neutron-capture cross-section and as an additive to various alloys because of its corrosion resistance [1]. In addition to those applications, attention has been recently paid to HfCh as a high-x"" dielectric used in ultra large scale integration, ULSI, as well as ZrCh, AI2O3 and La2C>3, which are expected to be alternatives to conventional S1O2 thin films [2].The materials used in ULSI are required to have a high purity in order to avoid unexpected errors due to impurities. Furthermore, high purity Hf is indispensable for investigating the intrinsic properties of Hf metal. Thus, it is significant to establish the purification process for Hf from both the industrial and academic perspectives."

Jan 1, 2012

By Selvin Yesilay, Guray Kaya, Bekir Karasu, Asli Cakir

"In this investigation, the wastes of Eti Maden Kirka Boron Company of Turkiye were evaluated in the production of diopside and anorthite-based glass-ceramic glazes suitable for porcelain tiles fast and single-fired under industrial conditions. First of all, high wear resistant frits were produced with the use of concentrator and derivative borax wastes. Second of all, pre-engobed porcelain tile bodies were coated with the standard and newly produced frit-based glazes and industrial fast single-firing was employed. Final products were undergone to the certain standard tests to determine their Vickers hardness, wear resistance, thermal expansion coefficient values, gloss and coloring parameters. The micro-structures and phase formations of the fired glazes were also studied. Consequently, it was confirmed that the utilization of borax solid wastes in fast single-fired porcelain tile glass-ceramic glazes is possible. Introduction Porcelain tiles were introduced at the end of 1980s by Friandre, one of the leading Italian porcelain manufacturers. The American National Standard Specifications for Ceramic Tile defines porcelain tiles as: dense, smooth, impervious (with water absorption value less than 0.5 %) and stain resistant [1]. The excellent technical performances for ceramic tiles, such as mechanical, wear, frost and chemical resistance that make their use possible in indoor and outdoor building applications [2-3]. In the last decade, the growth rate of the global production of porcelain tiles increased more than those of other ceramic products; in fact, the technical properties of porcelain tile, coupled with even more improved aesthetic appearance, gave it a prominent role on the tile market [2]. Glass-ceramics are composed materials of one or more crystalline phases immersed in a residual glassy phase [4-5]. Glass-ceramic technology is based on controlled nucleation and crystallization of bulk glass [6]. The concepts of controlled crystallization of glass designate the separation of a crystalline phase from the parent glass in the form of tiny crystals. Their growth rate and final size are controlled by a suitable heat treatment [7]."

Jan 1, 2008

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By Joel F. Flurnerfelt

Molten Al and Al alloys containing si, Mn, Ti, and y have been lanced with nitrogen-bearing gases. These lancing experiments provided the means for observing what phases form during exposure to nitrogen-bearing gases for finite periods of time, <2 minutes, at high temperatures, >1290oC. The experiments were conducted in sn induction heated drop tube furnace apparatus. The overall premise of these experiments was to select those Al alloys and gas compositions that show promise of forming secondary dispersoid phases, particularly AIN, in the Al matrix. The alloys selected will be atomized using gas atomization reaction synthesis (GARS) using the most favorable conditions. In this case, the chosen Al alloy will be atomized with a nitrogen-bearing gas, such that the Al and gaseous nitrogen species react to form a dispersoid phase within each powder particle. The powder particles that result from this "aggressive" GARS-process would be essentially Al metal-matrix composites within a uniform distribution of dispersoids. To date, only high-purity Al has been atomized using a mild GARS reaction. This work is funded by the Materials Science Division of DOE-BES under contract number W-7405-Eng-82.

Jan 1, 1996

By T. Xin

A vertical grain boundary intercepting a horizontal free surface forms a groove to reduce the combined surface energy of the system. We study grooving by surface diffusion with anisotropic surface energy. A recently developed delta-function model of facets is used to describe the surface energy with three or four fold symmetry. It is found that the groove grows following a similarity law. The self-similar groove profile is solved numerically by a shooting method. Even with strong anisotropy, the groove profile can be smooth if the exposed surface orientations do not include a facet orientation. The smooth self-similar groove shape is the same as an isotropic groove, but the size is reduced by a factor that depends on the degree of anisotropy. This induces a large error on the value of surface diffusivity if the isotropic model is used for an anisotropic system. In this talk. we will describe how to correct for this error.1 I Xin, T. and H. Wong, "Grain-Boundary Grooving by Surface Diffusion with Strong Surface Energy Anisotropy," Acta Materialia 51, 2305-2317 (2003). Keynotes: Grain growth, Surface Diffusion, Surface energy, Anisotropy

Jan 1, 2003

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By Ahmet Geveci

[Generally accepted formula related to sulfur slag-metal distribution ratio is given by the following equation: [ ] According to the above equation it can be deduced that sulfur distribution between slag and metal is governed mainly by metal composition (?s term), slag composition (slag basicity and in turn sulfide capacity), oxygen potential of the system (ao¬¬ term) and temperature(related to equilibrium constant, K). In this study, the results of ladle furnace operations conducted in Erdemir-Iron and Steel Works Co. (Turkey) in relation to sulfur removal, have been given. Typical ladle furnace slag analyses of 4937K quality steel have been presented. Activity coefficient of FetO,?FetO, have been calculated with the relation obtained fromthe literature. Activity calculations have been performed with the program written in Mathcad. The changes in activity of aFetO in the slag phase,, have also been studied in relation to the sulfur removal: The relation between % Decrease aFetO and %DeS (measured)have been investigated for 4937K runs and someother types of steel produced in the Erdemir Plant. Related to ladle operations %desulfurization defined as [(%Sinitial-%Sfinal)/S%initial]*100 values have been presented for different steel qualities.]

Jan 1, 2006

By G. S. Nus

Technology for treating man-made metal-containing raw materials in DC electric furnaces with polarization of the bottom phase (PDF furnaces) has been developed and proven on a semi-commercial scale. PDF furnaces permit processing of man-made raw materials, i.e. current and accumulated intermediate products with rather high contents of valuable metals (i.e. slags, sludge, residues, Waelz slag, etc.), as well as secondary raw materials and virtually any type of waste using an environmentally safe technique based on sublimation of volatile metals and transfer of non-volatile metals and sulfur into the bottom phase in the furnace. Processes developed on the basis of the use of PDF furnaces make it possible to take advantage on a full commercial scale of electrolysis of molten materials, including electrochemical reduction of metals, intensification of their settling into the bottom phase and sublimation of volatile components, as well as to significantly improve recoveries of nonferrous metals, resolve the problem of excessive accretion formation in slagging processes and substantially improve the environmental situation. The low-grade discard slag obtained can be utilized in the construction industry; in particular, slag can be added to the limestone feed for cement manufacture.

Jan 1, 2006

By Kimio Itagaki

As a fundamental study for smelting the copper matte with high contents of arsenic and antimony in a strongly reducing condition, phase relations between the liquid matte and copper-rich alloy phases in the Cu-Fe-S-As or -Sb quaternary system and between the liquid matte and iron-rich alloy phases in the Cu-Fe-S-As or -Sb system saturated with carbon were determined at 1473 K by a quenching method. Activities of arsenic and antimony in these systems were also measured at 1473K by Knudsen cell-mass spectrometry. Furthermore, distribution ratios of silver, gold and platinum between the liquid matte and copper-rich or iron-rich alloy phases were determined in relation to the arsenic or antimony content in the systems. On the basis of these data, the elimination of arsenic and antimony from the matte to the iron-rich alloy (speiss) and the recovery of precious metals in reduction smelting of the copper matte were evaluated. It was suggested that the addition of pig iron to make a strongly reducing condition and form the iron-rich alloy, which is fluid at smelting temperatures, will be useful for fixing arsenic in the speiss.

Jan 1, 2006

By Maria de Campos

The pre-reduction behaviour of chromite particles in methane-argon and methane-hydrogen gas mixtures was investigated between 1050°C and 1250°C. Loose bed of chromite particles were reacted in a vertical tube furnace under a pre-set gas mixture predetermined time intervals. Metallization results were obtained for the Cr and Fe components by chemically analyzing the reaction products. SEM-EDAX techniques and X-ray diffraction were employed to elucidate the reduction mechanism. It was found that higher reduction kinetics and higher Cr:Fe ratios in the metal phase would be achieved when hydrocarbon gas was used in comparison to classical carbothermic reduction at a given temperature. The reduction rate was generally bulk gas mass transfer controlled to the reaction site for initial stages which then was followed by ionic diffusion rate control. It is proposed that methane did not partake directly in the reduction but cracked, presenting the reaction site with hydrogen gas and atomic carbon, which was able to immediately react at the immediate area of reduction regeneration CO and H2 and thus maintaining a low partial pressure of oxygen at the reaction site.

Jan 1, 2006

By Hector M. Henao

In order to provide the thermochemical data regarding the slag system, which are of importance for sulfide smelting and metallurgical processes but still lacking, an experimental study was carried out on the phase relations and activity of iron oxide in the FeOX-CaO-SiO2 system at temperatures between 1300 and 1400 °C and partial pressures of oxygen between 10-9 and 10-4atm. First, the solubility of CaO and SiO2 in the solid FeO were obtained and the tie lines connecting between the solid wustite (FeO) or magnetite (Fe3O4) phase and the liquid phase were determined. Secondly, iso-activity lines for FeO in the homogeneous liquid region were determined, based on the activity of iron in the Pt-crucible used in the equilibrium experiments. The activity coefficient of FeO in this region was also derived from the composition of FeO and FeO1.5 in the liquid region. Finally, the effect of (CaO/SiO2) ratio in the system and partial pressure of oxygen on these thermochemical quantities is discussed.

Jan 1, 2006

By Helena Byrdziak

KGHM Polska Miedz S.A. is a significant European copper producer with production of 447,000 mtpy, operating three underground mines and three smelters. The company has been involved for years in environmental activity, which was stimulated not only by the company itself, but by the development of environmental regulations as well. The first set of regulations, concerning water protection, was&apos; established in Poland&apos; in 1974, while a comprehensive environmental law was passed in 1980. This law in general requires industry to submit all data of environmental significance to the local authorities. Based on this data, they establish limits concerning emissions into the air, water and ground, the amount of wastes produced and the means of their disposal. A company has to pay fees for each tonne of emitted substances and stored wastes. When the emission of a substance exceeds the limit, the company has to pay a penalty which is about ten times higher than the fees. This approach in general is effective because it forces companies toward: reduction of their emissions. The problem is that the law is constantly subject to change and is becoming not only more restrictive but is involving more and more bureaucracy.

Jan 1, 1999

By Varadajan Seshadri

Torpedo cars have been extensively used for pig iron desulfurization although its geometry is not considered to be ideal as far as mixing and mass transfer are concerned. Complications arise from scaffolds formed through aggregation of flux, slag and pig iron during operation. Following industry demand a 1:6 torpedo car physical model was operated to assess the optimum refining conditions for pig iron desulfurization. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation, presence of scaffold were evaluated. Mixing times were found to be shorter than regular desulfurization time and also not very sensitive to scaffold presence. Scaffold contributes to the reduction of the useful volume only. Mass transfer at the permanent reactor is more effective when the torpedo is operated at its full capacity. The experiments also highlight the dominance of the transitory reactor as compared with the permanent reactor.

Jan 1, 2006