Search Documents

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By Martín Reyes

Iron concentration by ion flotation techniques, from sulfate solutions in presence of zinc was studied in a laboratory flotation column by continuous mode using a synthesized sand shell plate sparger, an anionic collector, promoters, and surfactant propylenglicol 400. Effects of experimental parameters, such as the concentration of reagent: potassium amyl xanthate and dithiophosphate, superficial gas velocity, and superficial liquid velocity were studied in terms of the recovery and enrichment of Fe (III). The results show that the iron elimination from the solution in the presence and absence of zinc (II) are of 59 % and 72 % respectively. The flotation efficiencies decrease with an increase of the concentration of xanthate and air flow rate. The best recovery was achieved, at Jg 0.1 cm/s, Jl 0.72 cm/s and a mixture of xanthate and dithiophosphate as promoter. It was also demonstrated that it is possible to selectively separate and concentrate iron (III) from solutions containing zinc. The behavior of iron ion flotation in a flotation column is reported in this research as a gas hold up, superficial gas velocity, bubble size and superficial bubbles area flux function. The results show that the extraction of aqueous ions of metal iron by ion flotation is strongly affected by: [C], Jg (cm/s), eg (%), Db (mm), Jl (cm/s), y Sb (s-1).

Jan 1, 2009

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920's and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990's. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By H. H. Law

Large amounts of waste material in the form of flue dust are generated in the operation of copper smelter furnaces. As a result of increasingly stringent disposal, it has become important to develop methods for treating such metallurgical wastes to extract metals and convert them into salable products. A two-step closed-loop hydrometallurgical process, has been developed: (1) extraction with sulfuric acid removes about 90% of zinc and decreases the dust volume by 50%; (2) extraction with hydrochloric acid dissolves the lead and further decrease the dust volume by 75%. A process scheme for generating salable products is proposed.

Jan 1, 1992

By Takeshi Yoshikawa, Kazuki Morita, Yuichi Kato

"A composite composed of carbon fiber and a Cu-Si alloy is a promising candidate for next generation brake disc materials used in high-speed trains. The composite can be prepared by vacuum infiltration of the Cu-Si alloy into the fibrous carbon matrix. The activity of Si in the alloy plays an important role in controlling the formation of SiC; this formation is attributed to the reaction between the Si in the alloy and the carbon fiber during the infiltration process. Because Fe has strong affinity with Si, the addition of Fe is expected to decrease the activity of Si in the alloy. In the present work, the variation in the activity of Si in the alloy with the addition of Fe has been investigated by equilibrating a Cu-Fe-Si alloy with solid SiO2 and graphite under controlled CO partial pressure. The first-order and second-order interaction parameter of Fe on Si in molten Cu was determined to be -16 and 160, respectively. The negative value of the first-order interaction parameter clarified the addition of Fe to the Cu-Si alloy is effective in decreasing the activity of Si in the alloy.IntroductionIron-based materials have been commonly used for brake discs in high-speed trains. It becomes critical for brake disc materials to withstand high thermal loads with an increase in the maximum speed of high-speed trains. The fabrication of high heat-resistant, light-weight brake disc materials is then crucial for their use in next-generation high-speed trains. Carbon fiber is known to be a light-weight, high-strength material, and is considered to be a promising matrix material for use in brake discs. The Cu-Si alloy exhibits high thermal conductivity. The composite in which the Cu-Si alloy is added to the carbon fiber matrix is expected to be a high performance material for brake discs. The composite can be prepared by the infiltration of the Cu-Si alloy into the carbon fiber matrix at a temperature higher than 1700 K."

Jan 1, 2012

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By J. S. Lee

A new high performance adsorbent is synthesized by the sol-gel method and applied to the removal of cadmium and mercury ions from aqueous solutions. Adsorbents based on metal oxides have been developed by immobilizing chelating molecules on the surface of the existing metal oxide networks and show ability for selective metal extraction from aqueous solutions. However, efficiencies of such adsorbents are limited due to low ligand density, and difficulty in pore accessibility. These difficulties are circumvented by synthesizing adsorbents using the sol-gel technique. In one example to be discussed, the sol-precursor possesses an organic moiety that binds cadmium, mercury, and copper ions. The capacities of 1.98mmol Cd(II-/gm and 6.40 mmol Hg/gm of this adsorbent are considerably higher than those of adsorbents prepared by the ligand immobilization technique. The scope of this paper is to discuss the development of the new adsorbent and its applications for cadmium and mercury removal from aqueous solutions.

Jan 1, 1999

By B. Ozturk, K. Ito, R. J. Fruehan

"A simulation model for bath smelting processes for the production of iron was developed which predicts the coal, flux, ore, and oxygen consumptions and the off gas volume, temperature and composition. The model is comprehensive in that it takes into account all of the important variables including coal composition, metal composition, ore composition, slag basicity, post combustion ratio, (PCR), prereduction degree (PRO), heat transfer coefficient (HTC) , flux, scrap charge, and heat losses. Four basic cases were considered: I. 30% PRO-50% PCR; II. 90% PRO-O% PCR; III. 60% PRO-30% PCR; and IV. 0% PRO-50% PCR. Several different coals were considered and a sensitivity analysis of the critical variables was performed. The model also estimates the sulfur content of the metal. The major conclusions included:1. Post combustion significantly reduces coal consumption but above 20% PCR little reduction of FeO to Fe can be performed with the off gas.2. Prereducing to FeO (Case I) and having as much post combustion as consistent with good heat transfer is an attractive process. This process only requires a simple pre reducer, uses less coal, and is relatively insensitive to the type of coal used.3. High off gas temperatures may pose a potential problem. The off gas temperature can be reduced by using an 02-Air mixture for post combustion, limiting post combustion or adding water to the gas.4. The use of CaC03 in place of CaO or of supplemental electricity does not appear attractive.5. The melting unit is theoretically an energy efficient scrap melter. For Case I using 200 kg of scrap as part of the charge the coal consumption decreases by about 80 kg.6. With PCR > 30% the FeO content of the slag is expected to be 2-5%, and the metal will not be saturated with carbon. These factors and the increased sulfur load since coal is the fuel indicate the sulfur content of the metal may exceed 0.25%"

Jan 1, 1988

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340° C by the two probe method using an ultra high resistance meter. The II: value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it monotonically increased from 10-5 to 10-4 (omega) 1cm-4 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the II: value. The II: value increased with the increase of Na proportion in the melt. For a 10 mol% Na doped sulfur melt it was as high as max. ~30 (omega) 1cm-1 above 180°C under the irradiation of ultrasonics.

Jan 1, 2003

By Baozhong Zhao

In-situ vitrification (ISV) is a new technology used for treating radioactive, organic and inorganic contaminated soils. In this process, electricity is applied through electrodes buried in the contaminated soil to melt it and form an environmentally stable glass-like solid. The organic contaminants and volatile metals are vaporized during heating up, the non-volatile inorganic elements are dissolved and incorporated into the melt. In present full-scale operation, the ISV process can treat 4 to 6 tons of soil per hour at consumption of about 1000 kwh per ton of soil. In this study, various configurations of electrodes were examined in a mathematical model. The results may be used to optimize the ISV process.

Jan 1, 1994

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, 'S02 control, and process simplicity.

Jan 1, 1983

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340'C by the two probe method using an ultra high resistance meter. The k value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it mouutuniocally increased from 10-5 to10-4 A' 1 cm-1 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the K value. The k value increased with the increase of Na proportion in the melt. For a 10mol% Na doped sulfur melt it was as high as max ~30 A 1cm -1 above 180 C under the irradiation of of ultrasconics.

Jan 1, 2003

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By G. Belardi

A study has been conducted to assess a new wet beneficiation treatment for the recovery of the sulphuric-acid-soluble titanium oxide contained in the waste from an Italian TiO2-pigment facility. The waste is produced during treatment of a Ti-enriched slag and contains as main components TiO2 (54%, of which 42% acid-soluble and 12% insoluble), SiO2 (27%) and A1203 (6%). Eighty percent of the material is finer than 50pm. The first step was to ascertain the possibilities offered by size classification, wet gravity separation, froth flotation and wet high-intensity magnetic separation to improve the grade and recovery of Ti02 and reduce the SiO2 content. The next step was to optimize the operating conditions of the various separations and assemble them into a complete flow- sheet. Beneficiation ensures potentially 70% recovery of the TiO2 with a concentrate grade of 80%.

Jan 1, 1998