Search Documents

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Scott Scovira, Ruilin Yang

This paper presents a non-waveform blast vibration model for the near-fi eld. The model uses the concept of a dominant charge augmented by other contributing charges estimated using a scaled time window. The model accounts for the effect of broken ground created by earlier fi ring holes, amplitude attenuation, effects of signal broadening with travel distance from frequency attenuation, as well as asynchronous propagation of different wave types due to the wave velocity difference, the delay time effect, and non-linear superposition of near-fi eld vibration. The model uses an effective distance defi ned from the broken ground screening, and determines a dominant charge contributing to the PPV at a monitoring station. Then the model uses a time window for each individual charge to determine if it contributes to the PPV. The time window has a variable width to model the effects of the signal broadening with travel distance. For modeling the signal broadening, a generalized rock quality factor Qd is proposed. The time window includes a weighting function that diminishes the contribution for charges fi ring further from the dominant charge and this accounts for contribution arising from the timing difference between a contributing charge and the dominant charge. The model uses a non-linear charge weight superposition technique that scales the charge weights within the time window to the same distance of the dominant charge and superimposes the scaled charge weight. The case study demonstrates that the model provides useful predictions for near-fi eld blast vibrations.

Jan 1, 2008

By Huang Daguang, Paulo Couceiro, Juan Navarro

Mining is typically conducted through a set of interdependent unit-operations, which commonly include drilling, blasting, digging and hauling, in order to deliver the required ore material into the comminution circuit and to remove waste rock with minimum impact in the operation. In such complex environment, the identification of critical paths, and respective interfaces between different unit-operations, are necessary to determine a sustainable long-term operational program. Facing this challenge, adaptive cost optimization strategies are required to increase productivity and revenue while minimizing potential environmental impacts. Since the overall mining efficiency can be strongly impacted by blasting outcomes, an operating method based on the searching of the ideal blast design is required in order to minimize the mine total cost of ownership. The implementation of a consistent continuous improvement program requires specific care in terms of design, control and execution of the different stages of blasting. For that, the application of the most advanced technologies for rock characterization, based on drill monitoring systems, and smart explosive products, allows the improvement and control of blast results by adapting the explosive energy distribution to the rock condition, so as to optimize the performance of downstream stages such as digging, hauling and comminution. This paper describes the application of a heuristic optimization approach, where blast parameters are used as decision variables to evaluate the potential impact of several blasting scenarios on subsequent unit operations, under the continuous ability of modelling, measuring and calibrating operational performances along of the mine cycle.

Feb 6, 2023

By Evan Boone, Peter Bellairs

A technical services visit was conducted to determine the initial parameters to successfully presplit several benches for an input crusher installation at the Wolffdene quarry. The paper details the preliminary design utilising both detonating cord only and specialised presplit product charges and compares these to the final designs utilised based on site experience. The role of accurate drilling, explosive loading and geology in obtaining successful cost effective presplits is highlighted.

Jan 1, 1998

By B T. Lusk, Jhon J. Silva

"The original signature hole technique to predict vibration levels from blasting, is based on theassumption that each hole in a production blast, generates an identical vibration waveformarriving to the point of interest. When the same waveform is used to represent the vibrationproduced by each hole, the complete waveform for the whole blast is the convolution betweenthe waveform and the impulse sequence that represents the initiation timing of the blast. In thisresearch, several field tests were developed to establish the validity of the invariability of thewaveform hole-to-hole in a mining production blast. The results of the tests showed that thereare variations in amplitude and frequency content for the hole-to-hole waveforms. Thevariations can be explained due to the character of the parameters involved in a production blastbetween them: different vibration path for each hole, differences in the geometry of each hole,differences in the explosive charge for each hole (chemical and quantity), etc. This paperdescribes a methodology based on the main characteristics in both; time and frequency domainof any recorded signature waveform and uses Fourier series to approach one equation to generatedifferent random waveforms for each hole that can be used in the prediction of the completevibration record of the blast. The methodology is the base for signature hole analysis using aMonte Carlo scheme."

Jan 1, 2012

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Frank Hirthammer

The paper explains the procedure of implementing Track & Trace solutions for manufacturers of explosives based on customer experiences. By using concrete examples, the process from project start to implementation is described. Lessons learned from the experiences of European explosives manufacturers are presented.

Feb 1, 2020

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Francisco Sena Leite, Thomas Palangio, Vinicius Miranda

With an increasing pressure to find efficiencies in the mining industry, operations are looking for continuous improvement tools to validate blasting procedures, a crucial and often overlooked area of the process. Using case studies completed at both small and large-scale mining operations, this technical paper proposes a practical methodology for pattern expansion studies, taking into account terrain parameters, rock quality and explosive strength. This technical paper will use a series of tools geared towards an economical continuous improvement procedure, using UAV particle size analysis to optimize blasting based on “generalized reduced gradient” for non-linear problems, with cost savings being the main objective. For the validation of this methodology, one scenario was created based on the operation’s budget: an economical continuous improvement plan that relied on manual data collection methods in order to baseline and optimize procedures.

Jan 1, 2018

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By David Porter, Nathan Rouse

The implementation of presplit blasting has been widely utilized in open pit and underground tunneling. This case study works through the iterative process of developing a heading drill and blast design to control overbreak and limit backbreak in cut and fill headings. The initial design was based on rule of thumb parameters, and the design was then modified for the field conditions based on results. Throughout the design process the drill profile, explosive charge, and timing were modified to yield the best profile compared to design. Data collection during the design process was extensive to best understand the effect of modifying parameters, and gauge performance of design changes. Input from the miners as well as engineers was considered to allow for the best possible adaptation of the design change from existing practices. During the process resistance to change was realized and accounted for to understand the issues that the miners were facing and how to best address them while ensuring high quality blasting. Workforce buy- in was addressed by illustrating the long term benefits of higher quality blasting and the tradeoff of with a slightly more in depth drill and loading cycle.

Feb 6, 2023

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011