Search Documents

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By D P. Proudfoot, S G. Keith, D P. Onagi

A number of aspects of the Canadian concept for nuclear fuel waste disposal are being assessed by Atomic Energy of Canada Limited (AECL) in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, Canada. One of the major objectives of the work being carried out at the URL is to develop and evaluate the methods and technology to ensure safe, permanent disposal of Canada's nuclear fuel waste.

Jan 1, 1996

By David R. Ziegler

Blasting complaints are as unpredictable as human nature. Being prepared to speak to the complainant, and having a good idea of what you should say, or what NOT to say, may affect the evolution, and eventual resolution of the complaint. The person taking that first phone call will probably not be responsible for resolving the complaint. However, the person in charge should respond to the complainant ASAP, the same day, if possible.

Jan 1, 1998

By J R. Phin

The properties of all available modern blasting initiation techniques are reviewed. Primadets are nonelectric initiators, the nonelectric features of the system eliminates concern of premature initiation from static or stray currents. The loading techniques are simple and a minimum of training is required. There is no limitation in the number of necessary sequences in which the Primadet need be connected for initiation. This flexibility improves vibration control,and often reduces costs due to increased fragmentation.

Jan 1, 1975

By R DeLon Hunsaker

In the past, quarrying and other small operations have not been able to take advantage of the lower cost, convenience and better performance of bulk slurries. However, with the introduction of repumpable emulsion slurries and their ability to be stored in containers as blasting agents, bulk slurries are now available for small operations with small diameter boreholes and are producing excellent results. This same concept is being used successfully in larger underground operations.

Jan 1, 1984

By Shulin Nie

The dead-pressing phenomenon in emulsion explosives is wellknown. Research work on this subject has been carried out at the Swedish Detonic Research Foundation for the last few years. Several experiments with emulsion explosives under dynamic pressure condition have been carried out both in iron pipes and in blast holes in rock. The main object was to study the critical amplitude and duration of the pressure causing the explosive to be dead-pressed.

Jan 1, 1993

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Paul Downing

A major component of an effective blasting company safety program is the self-audit. A self-audit can help reveal hazardous conditions that should be corrected and training needs that should be addressed before accidents occur, insurance claims are filed, and/or fines are levied. Such audits, when they lead to appropriate corrective action, can provide significant economic benefits for employers by reducing the costs associated with insurance claims, accidents, and injuries.

Jan 1, 2001

By James W. Reil, Douglas A. Anderson

Common wisdom has it that a blast which breaks rock efficiently should-generate less ground vibration. In practice, however, this idea has not been-rigorously tested. In a previous paper presented at an SEE meeting[1] we described a method for-controlling vibration using delays. The method is very effective in controlling-annoying low-frequency ground vibration. We noted that observed ground-vibration differs in some respects from that predicted by adding single-charge-waveforms.

Jan 1, 1988

By Alfred Osborne

Progressive cavity type pumps are widely used by commercial explosive manufacturers for pumping water gel, emulsion and emulsion / ANFO blend explosives. Tests by explosives companies and investigations into incidents have shown that this type of pump can develop dangerously high temperatures when operated deadheaded or dry. [i.e. with no flow of product through the pump.] In some tests and incidents, explosion or detonation of the explosive (or residual explosive) in the pump has resulted.

Jan 1, 2002

In this work, is being described the developing of the study for the demolition by controlled blasting project of a building of reinforced concrete, in the center of a spanish city. Synthetically, it is being analyzed the timing of the fall of the parts of the structure. This documentation is completed with a group of four photographs of the falling sequence and a film about several demolitions and the particular one described in this paper.

Jan 1, 1977

By Ivan Kovac, Pero Marjanovic, Branko Bozic

"The paper deals with results of geophysical survey of the rock masses, and the blasting parameterswhich have effect on the fragmentation in quarries . A relationship between the burden, which is the distance between the charged borehole and the free rock surface, and the velocity of longitudinal waves in the rock mass is established based on measured values for different quarries. It is shown that the drilling geometry can also be detemrined from this relationship."

Jan 1, 1999

By Walter Jr Duke

The security of explosive materials is a vital concern to every mine, quarry and contractor engaged in blasting. Proper construction of magazines and sufficient locking mechanisms are the fundamental means of maintaining secure storage. The object of this paper is to review the proper methods of construction of storage facilities for explosives as defined by the Alcohol, Tobacco, and Firearms regulations. Subpart K subsection 55.208 and the Institute of Makers of Explosives recommendations.

Jan 1, 1991

By Gerald R. Coonan

Laboratory research is being conducted to substantiate suggested levels for voluntary standards on human response to transient vibration. The application of those findings to actual field conditions, however, will be limited because they will not include social and psychological factors existent in the real world. It is necessary, therefore, to examine available empirical information on complaints in an attempt to define the influence social and psychological factors might have on the laboratory results.

Jan 1, 1982

By Detlef Sulzer, Winfried Rosenstock

"At the end of this century a great breakthrough in the field of blasting technology is finally going tobecome reality. That, in the true sense of the word, is the long expected and desired “HighTechnology Blasting”. So far trials have been carried out in Australia, Africa and Europe with remarkable results, that have been predicted by the authors. As a result, significant reductions of explosives and drilling expenditure are emerging for the future."

Jan 1, 1999

By Murray B. Lytle

The Fording River Operations of Fording Coal Ltd. in southeastern British Columbia is producing 45 million long tons of clean metallurgical coal for shipment to the Japanese steel industry on a 15 year contract. The mine employs conventional truck/shovel operations as well as a walking dragline to mine coal in two mining areas. The coal is processed by conventional means to produce 3.0 million long tons per year of medium volatile coking coal.

Jan 1, 1978

By John P. Ashby

Production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the amount of damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts.

Jan 1, 1980

By Peter N. Calder, John N. Tuomi

The development of a successful control blasting program for an open pit iron mine in hard jointed rock is described. The objectives and mechanics of control blasting are discussed. Design and implementation procedures, which should have wide application, are given. Small diameter angle hole pre-split blasting, buffer blasting with production holes in front of pre-split lines and in front of strongly defined rock structures, and vibration control of production blasts are dealt with.

Jan 1, 1980

By Larry Schneider

In the construction field and to a lesser degree in mining, flagman are often necessary to move traffic and or pedestrians through work zones. Everyone readily recognizes that they are essential for the safety of the general public and the employees on the job. What is not often considered is the safety of the flagmen themselves. Actually, let’s call these employees “flaggers” recognizing the fact that there are as many women as men doing this job. The first problem we need to overcome is the misperception that flagging is a low skill function that can be done by any untrained employee. The reality is that the flagger works in a very hazardous position with serious responsibility for the safety of his fellow employees and the public at large. And to do this job properly re q u i re s that the flagger receive sufficient training before being sent out to the highway. It is also necessary to convince the flagger of the value and importance of their job in order to motivate them to do a professional job.testing, documentation of both, and accurate re c o rdkeeping are key aspects of HM126F. Of course, training and documentation requirements will vary depending on the type of operation involved, and there may be some differences in the application of requirements depending on your jursdiction. Nonetheless, failure to train and properly document such training can result in heavy fines and/or penalties.

Jan 1, 2004