Search Documents

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta's harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By K. Rainer Massarsch

In some parts of the world, vibrators are used extensively for different types of foundation engineering projects. If used correctly and in suitable soils then vibratory pile driving for example is very efficient. However, soil conditions and the installation procedure have great significance for the driving resistance and affect the bearing capacity of vibrated piles. Also the intensity of ground vibrations which are transmitted to the surrounding soil is affected by the vibration process. In spite of the increasing use of vibrators and the rapid development of vibrator technology, many aspects of pile-soil interaction are not yet understood. In order to asses the importance of factors, which govern pile installation (and extraction), it is necessary to consider the entire chain of vibration energy transmission from the vibration source to the pile, the interaction between the vibrating pile and the soil and the wave propagation in the subsoil, Fig. 1. [ ] Fig. 1. Transfer of vibration energy from the vibrator through the pile into the ground In the present paper, some important aspects of vibratory driving and their significance for pile installation and soil compaction will be discussed.

Jan 1, 1995

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987