Search Documents

By Mahmoud Shakeri1

Various types of thin-walled structures have been frequently used as energy absorbers to mitigate the adverse effects of impact and hence protect the vehicle structure under consideration when subjected to different loading conditions. Compression tubular structures that buckle in a progressive manner, can be used to advantage, providing inexpensive and versatile, but nevertheless weight and stroke efficient energy absorbers. In this paper quasi-static nonlinear finite element simulations are performed to study the effects of number of corners of the cross-section, wall thickness, plastic hardening rate of material, foam-filler and load angle on deformation mode and mean crushing force of tube. Crush strength increases as the number of corners of the cross-section increases, though it almost saturates for the number of corners beyond 11. Higher plastic hardening rate stabilizes the collapse pattern. Foam-filled tubes seem to have higher critical load angles in oblique loading and display a more stable and gradual decrease in mean load over the transition region. Substantial decrease in the initial peak load and dynamic load at any a given deflection was observed as the load angle increases. The investigation of bitubal arrangements and Multi-cell tubes reveals that these may be preferable to monotubal specimens due to the presence of the inner profiles. In addition, a comparison is conducted between the numerical and experimental results of the mean forces of some special angle elements. Good agreement is obtained.

Oct 1, 2011

By J. P. Nowlan

"This paper is an attempt to outline the structural problems at the Cochenour Willans mine, in so far as their details have been tentatively worked out. It must be emphasized that there are considerable data that can be interpreted in more than one way, and that further work may modify or completely change some of the hypotheses presented herein. Certain features, however, are sufficiently constant to warrant reliance on them when searching for extensions of orebodies.As the individual ore shoots usually have relatively small dimensions, but are often very high grade, structural details are of more than usual significance in laying out a mining programme. An illustration of this is a small shoot recently located and mined as a result of studying a minor slip cutting off a part of high grade gold ore in No. 319 stope. The shoot, which is bounded on three sides by slips, and on the fourth by the original stoping, was roughly triangular in plan, 20 feet on the base, and 40 feet in length. The average width mined was 4.5 feet, but the gold obtained totalled over 1,800 oz.The property lies in Dome township, east of McKenzie island, and consists of an original group of thirteen claims acquired from the Cochenour Willans syndicate, plus one additional group of five claims obtained by purchase from the Kelson Red Lake Gold Mines, Limited, and one other claim that rounds out the southeast corner of the block.The claims of the original group were staked by W. M. Cochenour, Dan Willans, and Horace Young, during 1926 and 1927. The Cochenour Willans Syndicate was formed in 1928, and until incorporation of the present Company work was carried on at varying intervals by several different interests, including Ventures Limited, Hollinger Consolidated, who sank a shaft to open up the 150-foot level, and by the Syndicate itself. The first ore from the property was shipped to the Gold Eagle mill by the present Company in 1939, and amounted to 4,959 tons, from which 2,360 oz. gold was recovered. The first brick was poured in December, 1939, and production has been continuous since that date. To the end of June, 1946, gold having a value of $5,982,000 has been produced from 345,033 tons of ore treated."

Jan 1, 1954

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By E. D. Kindle

"The Duthie mine is on the southwest slope of Hudson Bay mountain 7 1/2 miles west of Smithers, British Columbia. A good motor road about 15 miles long connects the mine with the Canadian National railway at Smithers. The principal workings are on the Henderson group of claims between elevations of 3,200 and 4,000 feet above sea-level. Silver, lead, and zinc were produced from this mine between 1924 and 1930.Three adit drifts known as the Compressor, McPherson, and Thompson levels were driven along the Henderson vein-lode in 1922, and the following year the operating company, known as Duthie Mines, Limited, shipped some high-grade silver-lead-zinc ore. Further shipments of high-grade, handsorted ore were made in 1926, and in 1927 a modern flotation-type mill was built, having a capacity of 50 tons of ore a day. Mining operations were suspended in March 1930."

Jan 1, 1954

By László Guczi1

Nanosize model gold particles with varying size were fabricated by deposition of a 10 nm thick gold film onto SiO2/Si(100) substrate by electron beam evaporation followed by modification using low energy Ar+ ion bombardment. The change in particle size were monitored by the Au 5d valence band states determined by ultraviolet photoelectron spectroscopy (UPS). The gold/iron oxide interface was studied by iron oxide deposition on gold. It was found that the energy profile of Au 5d valence band states are strongly redistributed with decreasing the gold particle size mostly affecting at the lowest and at the highest binding energies. The size effect in the UPS spectra can be interpreted by the energy redistribution rather, than by narrowing the 5d states. The iron oxide deposition increases the catalytic activity in CO oxidation whether it is on gold nanoparticles or on a continuous 80 nm thick gold film. The activity enhancement is significantly larger in case of gold nanoparticles. The interface interaction is operative in enlargement of the catalytic activity even if gold particles are not exposed to the surface, but they are located below the iron oxide layer.

Oct 1, 2003

By Y. Kusuda

Since 1981, the Annaka refinery has recovered zinc from zinc leach residues by the Waelz Process. The important considerations of this process are the prevention of the growth of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate. In this paper, simulation predictions and the results of the industrial operation regarding the prevention of coating accretions in the Waelz kiln and the improvement of the zinc volatilization rate at the Annaka refinery are reported and compared.

Jan 1, 2006

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By Chan-ho Park

As the building has recently become bigger, higher, and freeform, a technology called BIM(Building Information Modeling), which is a key technology that integrates construction and IT(Information Technology), has been rapidly introduced and expanded. Because BIM technology offers various benefits, countries that introduced BIM early has been actively promoted. However, misperceptions of BIM are prevalent in countries such as South Korea that have adopted it relatively late, with lack of awareness of its fundamental purposes. Under these circumstances, transparent and quantitative performance assessment needs to be executed in order to eliminate the misperceptions, and to explain and revitalize the BIM introduction. These quantitative performance measure KPI (Key Performance Indicators) to be measured should be prioritized. As derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, Uses the BSC to seek a balance between short-term financial goals, values and the value of long-term goals. Uses the BSC(Balanced Scorecards) to derive performance indicators in terms of the four types (financial, customer, internal processes, learning and growth), and performance management systems, seeking a balance between the value of short-term financial objectives and the value of long-term objectives. Through this, the KPI (Key Performance Indicators) which is used for measuring the effect of the BIM will be generated and also the method that can determine whether the generated KPI figures are objectively inter-connected will be suggested as well.

Aug 1, 2013

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

By Murray W. Grabinsky

The in situ performance of Cemented Paste Backfill (CPB) systems can be monitored to improve understanding of the paste?s behaviour and therefore optimize the geomechanical design of the cemented paste backfill system (i.e., minimize binder content, minimize fill barricade complexity, maximize fill rate-of-rise during backfilling, and minimize cure time before resuming production blasting in proximity). However, undertaking such a monitoring program is inherently complex, because the rate-of-rise and accompanying self-weight induced stresses occur at a time rate that is similar to the rate of hydration and associated increase in the paste?s stiffness and strength. In addition, arching within the stope complicates the overall stress distribution. Therefore, to obtain a complete picture of the CPB?s response, it is necessary to measure several variables (3-D total pressures, water pressures and suctions, hydration rates, and blasting induced vibrations) at a given ?point?, and take all such measurements at many points throughout the fill mass as well as at barricade locations. The overall testing program can therefore be logistically difficult to implement and have an apparent high cost. However, if the program is successful, the benefits arising from improved mine design can significantly outweigh the seemingly high initial capital and labour costs of the monitoring program. A case study involving an instrumented paste fill in a tall and narrow Alimak stope is briefly outlined. Plans for a similar experiment in a large long-hole stope are then considered.

May 1, 2008

By H. E. Frimmel

Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morphological characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively, estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry. Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infJ.1tration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in tum, was determined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By O. Laitinen, M. Rudolph, J. A. Sirviö, H. Liimatainen, R. Hartmann, University of Oulu

The increasing complexity of the ores composition worldwide calls for suitable collectors with specific properties, such as selectivity, wettability, and in regard to current regulations, environmental sustainability. Therefore, collectors have to satisfy many features to improve the efficiency of flotation processes. Cellulose nanocrystals gain more and more interest due to the versatile synthesis routes which enable the integration of specific functional groups and components with different degrees of hydrophobicity within the molecular structure. Consequently, cellulose nanocrystals can be employed in flotation processes as depressant or collector molecules, respectively. Nonetheless, the usage of cellulose nanocrystals is still limited due to a lack of the characterization of nanocrystal-mineral interactions and the change of the surface wetting properties of minerals after adsorption phenomena between nanocrystals and minerals. In these studies, butyl-amine cellulose nanocrystal (BAC) and quartz are used as model system to investigate physicochemical properties of both, BAC and quartz, and examine the applicability of BAC in flotation processes. Therefore, the surface charge distribution and electrophoretic mobility of BAC and quartz are investigated and compared to understand the effect of electrostatic interactions between BACs, and BAC and quartz. Based on this, the adsorption of BAC on quartz is examined. Finally, microflotation experiments test the efficiency of BAC to be used in flotation processes. The flotation response is correlated to the specific surface charge of BAC revealing the dominant effect of surface charges on effective particle-bubble adhesions.

Jan 1, 2016

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994

By D. M. Cruden

"When two discontinuities form a tetrahedral wedge in a rock slope, a factor of safety for the wedge can be simply calculated (if motion is driven only by gravity and resisted only by friction) from plots of the normals to discontinuities on an overlay of a polar, equal-area spherical projection to which the great circles of a similar equatorial projection have been added.IntroductionThe stability of slopes in rock masses is often controlled by the discontinuities that exist in the masses. In particular, the geometry of the discontinuities constrains the ways in which the mass may fail. Displaying the orientation of the discontinuities on a spherical projection has been found to be a useful way of identifying possible failure modes. The most concise display shows the orientation of the normals (or poles) to the discontinuities that compose the fabric of the rock mass. Computer processing of large samples of discontinuity orientations is necessary if the sampling biases identified by Terzaghi (1965) are to be routinely corrected. Fortunately, displays of the poles to discontinuities (or pi diagrams) are relatively easily produced on the line printer of a computer or by a computer plotter (Cruden , 1978; Ramsden and Cruden, 1979). Unfortunately, further analysis of the stability of a rock mass has tended to use traces of typical discontinuities on a spherical projection rather than pi diagrams; examples may be seen in Hoek and Bray's book (1981)."

Jan 1, 1990

By Gennaro Delisle

"Les Services TMG (Niobec) currently treat a niobium ore in the Chicoutimi area of Quebec. The mineral pyrochlore is present in a carbonatite deposit which assays 5% to 7% apatite.The ore is ground to minus 65 mesh and deslimed at 10 micrometres. Part of the carbonates are floated with a fatty acid emulsion and rejected to the tailings as a first step to ensure the proper conditions for the flotation of the pyrochlore concentrate. The carbonate concentrate is 65% minus 44 micrometres and is composed of dolomite, calcite, 22% apatite and a minor amount of silicates.A laboratory investigation was undertaken to determine the feasibility of extracting apatite from the carbonate concentrate. This led to the development of an economic flowsheet to produce high-grade apatite concentrate. The apatite is depressed with phosphoric acid, and the pH is adjusted at 4.8-5.0 with sulphuric acid. An additional amount of fatty acid is added to permit efficient flotation of the carbonates. 1n a second stage, the silicates left behind with the apatite concentrate can be removed by depressing the apatite with AIC3 while floating the silicates with a secondary amine.The results of the laboratory tests indicate the possibility of producing an apatite concentrate assaying 38.3% P2O5 (83.7% BPL) with a recovery of 66.2%. Pilot-plant tests undertaken at the concentrator yielded a concentrate of 34% P205 and recovery of 76%."

Jan 1, 1981

By Dennis V. Woods, J. Duncan Crone

"In order to determine its capabilities and to aid in the interpretation of fie ld results, a scale model study and field tests were carried out on the Crone borehole pulse electromagnetic (PEM) system. The model results indicate that if a borehole passes in the vicinity of a tabular conductive body, the system will not only detect the presence of the body, but will also return information as to its conductivity-thickness product, size, altitude and position.The effect of variation of these electromagnetic and geometric factors on the shape of the response curve from a borehole PEM survey is displayed by a number of suites of scale-model response curves. These model curves can be used directly as type curves in the interpretation of field results. Field tests of a prototype PEM system provide a check on the scale-model results and also summarize the procedure of interpreting field data using the model type curves.The borehole pulse EM system can be effectively used as a follow-up geophysical instrument for locating and delineating known conductive bodies. It can also be profitably utilized as a primary geophysical exploration tool in areas of deep mineralization below the depth limit of conventional airborne and ground geophysical systems. The probed area of a diamond drill hole in these cases is increased from a 1- inch drill core to a zone extending hundreds of feet from the hole."

Jan 1, 1980

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By Libao Zhu, David J. Williams, Nazife Erarslan

"Statistics show that the drawbell in underground mines is usually subjected to significant damage by impact loading due to falling ore. Drawbell damage causes a large quantity of residual ore to remain on the drawbell, thus leading to a huge waste of ore resources. In this study, the Cavity Monitoring System (CMS) and Surpac software were employed to visualize the 3-D damage. Also, the Discrete Element Method (DEM) was employed to perform simulations of the falling ore to investigate the damage evolution of drawbells under repeated ore impact and obtain the dynamic damage accumulation mechanism. The reason of drawbell damage was found due to the micro-shear cracks. The numerical simulations of a drawbell damage process under repeated impact loading showed the main failure type was shear failure and this type damage was found increasing with more ore falling. INTRODUCTIONDrawbells are an important part of underground mines and play a significant role in ore recovery in terms of safety, economy and efficiency (Brunton et al., 2010; Hustrulid & Bullock, 2001; Trueman et al., 2002). In most cases, blasted ore is gravitated along the drawbell and finally arrives at the footwall of the drawpoint. However, some of the blasted oversize ore blocks clog the drawbell road and those ore pieces are called hang ups (Penswick, 1997). However, any damage on a drawbell is believed to be the reason for these hang-ups. In the literature, researchers have reported that the stability of the draw-point is influenced by the stress distribution above and near the drawbell (Butcher, 1999; Neverov & Neverov, 2013). Much research in the literature has been done on draw-points in underground mines. In fact, rockfalls cause very serious damage on a small impact area in a very short time (Volkwein et al., 2011). Hoek (2000) pointed out that the blasted ore causes progressive ravelling and even collapse of the drawpoint, thus the ore in the stope is abandoned. In this paper, the Cavity Monitoring System (CMS) was employed to obtain the damage profile of a drawbell due to the impact of rockfalls and to confirm the residual blocking ore on the damaged drawbell. Then, the drawbell damage evolution due to repeated falling ore was simulated by the Discrete Element Method (DEM)."

Jan 1, 2015