Search Documents

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By H. D. S. Miller

"Artificial stope support has become an essential component of many underground mining operations. Because the use of cable bolts in open stopes is a relatively new concept, most support is still designed by trial and error or by rules of thumb. This often results in costly overdesigned support or inadequate support which leads to stope failure.This paper proposes guidelines to determine support requirements using the stability graph method. The stability graph method is an empirical open stope design technique that takes into account the key factors that influence stope stability. The factors for the design of a cable bolt support system include bolt length, bolt intensity and the original rock mass competency and can be estimated using empirically calibrated charts. The empirical charts were developed based on more than 60 case histories of cable bolting success and failure in Canadian open Slope mines.The concept of pre reinforcement and supp ort stiffness will also be discussed.INTRODUCTIONArtificial support, in the form of rock anchors, has become an important component of all underground mining operations because its stabilizing effect contributes to make underground workings safer. There are several types of rock anchors featuring different properties and having a variety of functions. This paper focusses on grouted cable bolt applications in large open stope mining. Such a support system may improve the competency of the disturbed rock mass to a point approaching the undisturbed rock quality by limiting joint movement and dilation. This results in more stable, possibly larger and, thus, more efficient production stopes."

Jan 1, 1989

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By P. K. Kaiser

3-D virtual reality (VR) visualization has opened new opportunities for complex 3D (x, y, z), 4D (x, y, z, t) or even nD data interpretation. The integration of common earth models (3D geologic data), mine models (3D excavations and stress), extraction models (1D time sequencing or mine sequencing) and nD monitoring data (e.g., seismic event parameters) into a common mining process model provides a platform for experts in various fields to better design, evaluate, monitor and modify mine plans throughout a mine?s life; from feasibility, through operation, to closure. Viewing seismic data in a stereoscopic VR environment within a mining process model offers data interpretation processes previously unavailable at lower dimensionality. MIRARCO has developed data analysis and viewing processes specifically designed to enhance microseismic and seismic data interpretation in a collaborative, immersive VR environment; bringing mine personnel and expert consultants together to evaluate data and make strategic decisions for cost effective and safe mining. Seismic events cause immediate hazards (rockbursts) and microseismicity causes gradual hazards through its cumulative effect in rockmass degradation. The focus of this paper is on understanding seismicity from a mine safety and mine planning perspective; in particular, how seismic migration patterns relate to the rockmass response to mining. The benefits of innovation in seismic data interpretation are significant, e.g., for hazardous work area identification, allowing better formulation of re-entry policies and workforce allocation planning, as well as allocation of effective support systems to strategic areas of elevated risk. Better understanding of the overall response of a mine to extraction also facilitates mine planning and design, assisting in reducing production costs and thus in enhancing profitability.

Apr 1, 2005

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By John Postle, Maureen Jensen, Marcel Vallee, Bernie Haystead, Dan Hora, Graham Clow

The Committee's proposed standards establish definitions and guidelines for the reporting of Exploration Information, Mineral Resources and Mineral Reserves in Canada and are identified as the "CIM Standards" and referred to as such hereafter in this document. To provide additional clarification to Qualified Persons (QPs), guidelines have been included with the respective definitions. The CIM Standards are applicable to all minerals including industrial minerals, diamonds and other gemstones. Reserve definitions for bitumen, natural gas and oil are not included in these Standards. The CIM Standards are not intended to cover mineral inventory estimates that will be reported to government agencies.

Jan 1, 2001

By Walter K. (Cory) Conrad

Two pumping tests in the Chilson Member of the lower Lakota Formation were completed at nearly the same location in 1979 and 2008. The 1979 test consisted of a pumping well and several surrounding observation wells penetrating the full 55-m thickness of the aquifer. The 2008 test consisted of a pumping well and three surrounding observation wells screened over 10 m in one of the known uranium ore horizons in the lower portion of the Lakota penetrated only about 3 meters of the more than 55-m thick lower Lakota aquifer. The average transmissivity and storativity values determined from the 1979 tests were 17.6 m2/day and 1.8 x 10-4, respectively. Comparing median transmissivity of 13.9 m2/day and storativity of 1.2 x 10-4 determined in the 2008 test to the 1979 test, the new aquifer parameters for the lower Lakota are respectively about 80 and 70 percent of the 1979 results. Because transmissivity and storativity depend on aquifer thickness, comparing the results suggests that there may be some scaling effect between the tests due to the differing lengths of screened intervals. However, the effect cannot be predicted by calculations such as relative screen lengths or open intervals to the formation, or sandstone versus shale thicknesses on geophysical logs. The scaling effect is attributed to partial disconnection between the lower and upper portions of the Lakota Formation aquifer by locally continuous shale interbeds. Suggestions to resolve this scaling issue are presented.

Aug 1, 2010

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By David J. McDougall

"IntroductionThe production of pig iron, wrought iron bars and castings in Quebec during the 18th and 19th centuries has been so closely identified by historians with the Forges du St. Maurice on the St. Maurice River a few miles north of Trois Rivières (Three Rivers), that one is sometimes left with the impression that it was the only iron works that ever operated in the province. There were however, about twelve others, one of which was so completely re-built that it should probably be considered as a separate entity. All but two were constructed after the midpoint of the 1800s, coinciding with the growing Canadian demand for ""charcoal pig"" for railway car wheels and castings for industry, and about half of them were technically, if not economically, successful. The misconception about the Forges du St. Maurice may have come about either because of its long history of somewhat less than continuous production over a century and a half, or a tendency of Quebec historians to concentrate on events in the French-Canadian rather than the English-Canadian milieu, but whatever the reason, the other Quebec iron work s have been generally ignored. All but one of the Quebec blast furnaces could be described as ""preindustrial"" with capacities ranging between three and ten tons per day, the exception being the Radnor furnace built in 1892 with a maximum production of about 35 tons per day and an alleged capacity of 50 tons per day.Until a railway network was completed in the 1880s, the location of all the Quebec iron works except the Grantham Iron works was dictated by close proximity to adequate ore reserves because horse transport was of little use beyond a ten-mile radius. The other essentials of forest resources (mainly soft woods) for charcoal, limestone for flux and water power, were generally available except within a few miles on either side of the St. Lawrence river. Among the dozen iron works established in Quebec between 1732 and 1880, seven used bog iron ore in charcoal-fired furnaces."

Jan 1, 1983

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By G. A. Gross

Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained fom iron-formation; another 20 per cent was formed by natural enrichment processes. Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical composition and environment of deposition are of special significance in their evaluation as ore.

Feb 1, 1966

By C R. Crook

A brief outline of production methods and processes is given to show how maintenance fits into the picture at this plant. The work force, and the tools needed to carry out this function, are then described. Preventive maintenance practices, scheduled annual shutdowns and routine check-downs are explained, especially as related to planning and to the materials and labour involved for a mini-mum downtime. A brief explanation of the materials, sup-plies and spare parts program, as well as the part played by the Stores Department in conjunction with the Maintenance Department, is given. Cost control and equipment expenditure indicators are explained. Some specific examples of maintenance jobs are described in order to show the flexibility of the program. S HERRITT GORDON Mines Limited has been in continuous production, except for the planned downtimes needed for expansion tie-ins, or the annual shutdown check-over periods, since the first shipment of nickel on a commercial basis in July of 1954.

Jan 1, 1964

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By W. R. Horn

"WHAT I PROPOSE TO DO is to review or report very briefly and generally on the most important subject areas of environmental concern within the mining industry and to indicate the progress being made. First, however, it seems to me both appropriate and necessary to refer to what I said in an address to the CIM Annual Western Meeting, in November 1971, in Vancouver. At that time, I tried to convey: that the awareness and alertness of this far-flung and diversified industry was sharply on the up-swing; that the knowledge of helpful technology for the abatement of pollution by water and solids was significantly increasing; that most mines were doing something about it; that many had already achieved a recycling of process water to a really significant extent; that progress was being made - though not without considerable difficulty - on the large-scale neutralization and subsequent chemical treatment of acid- and metals-bearing waters; that increasing work was being done by individual mining companies on methods for the vegetation of completed tailings impoundments; and that it had been possible to develop a meaningful estimate of the amount of money to be spent by the industry on environmental control measures during the period 1971-75 (as much as $500,- 000,000 ) . Reference was also made at that time to the constructive work in hand toward the fixation, elimination or dispersion of sulphur from smelters and to the considerable attention which was being given by the indust(y itself toward in-plant problems, e.g., dust and noise. Finally, note was taken of the fact that the inclusion of environmental control costs in the pre-operational financial provisions of new mining operations is now established practice."

Jan 1, 1973

By T. A. Wedge

This paper suggests a crude correction for the impact of raw material quality on factor productivity in the Canadian mining industry. Such a correction would give a figure more dependent on the changing efficiency of the use of labour and capital, and less dependent on the effects of unquantified changes in inputs.

Jan 1, 1973

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By George Langford

Introduction The fiftieth anniversary is, for an individual or a society, an appropriate time for a review of the past so that events and experiences may be viewed m perspective, and thereby serve as a useful guide to the future. In this review of mining geology it is proposed to set forth the situation as it was when the Institute was founded, and then trace the developments during three appropriate periods-the first from 1898 to 1918 the second from 1919 to 1939 and the third from 1939 to 1948. Mining activities were widespread in Canada in 1898 and some of the operations were considered large for their day. The total value of the metals produced in that year was $21,705,854, and in the case of five metals the output had a value in excess of one million dollars. In order of importance these were gold, silver, copper, nickel, and lead. The important producing areas were ova Scotia, Quebec, Ontario British Columbia, and Yukon. This diversification of the mining areas and the metals produced created an interest in mining throughout Canada, and was an important factor in making Canadians conscious of their mining industry. In the year 1898 geology was a recognized science. The principles of physical geology were well known, but the same cannot be said of economic geology and structural geology. Ore deposits and their occurrence had been studied chiefly in Europe. A great many important observations had been made but the theories linking these facts together were still m a formative stage. The same condition was true of structural geology. These two branches of geological science which are so important in what is now called 'mining geology', had not progressed far enough to be of practical assistance mining operations. For this reason, geologists were regarded as dreamers in ivory towers-a concept chat still lingers in the minds of those who have not kept abreast of the growth of the science.

Jan 1, 1948

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950