Search Documents

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By D. C. Fraser

Copper occurs invisibly in a geo-logical environment characterized by swampy conditions and an accumulation of forest peat. This swamp, located in southeastern New Brunswick, contains up to ten per cent cop-per (dry weight), in the organic sediments. This occurrence appears unique in that the metal is apparently organically combined in a chelate compound. Unlike the acidic nature of most peat bogs, the pH of the cup-riferous peat is nearly neutral. Analyses of the peat and associated soils have indicated that the bulk of the copper is contained in the organic sediments. It appears that the cop-per distribution is affected by capillarity, evaporation and the growth of frost crystals, and that the copper fixation is effected by organic sequestration resulting in the metal being bound to the nitrogen or oxygen components of the forest peat. While such a fixation mechanism is not definitely established as responsible for the immobilization of the metal, the facts at hand are compatible with

Jan 1, 1961

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By M. Staite

This paper analyzed the feasibility of converting a 5kW natural gas SOFC power generator system designed to operate on natural gas to be fuelled by methanol. The analysis included laboratory methanol fuel processing experimentation, methanol reformate SOFC cell testing, and SOFC system mass and energy balance modelling. Methanol fuel processing experimentation indicated that theoretical reformate compositions can be achieved for high temperature (600-900°C) methanol steam reforming. A 6% open circuit voltage decrease and a 10% peak power current density decrease between cell operation on humidified hydrogen and methanol reformate was observed. SOFC system mass and energy balance modelling indicated that a natural gas SOFC system can be converted to operate on methanol fuel with minimal (1%) efficiency impacts, however the systems' thermal integration can be impacted.

Jan 1, 2005

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019

By G. A. Bezuidenhout, J. Davis, S. Lefume, J. P. T. Kapusta, D. K. Chibwe

"Although the centennial of the Peirce-Smith (PS) converting process has recently been celebrated, the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration. In the late 70’s and early 80’s, Brimacombe and co-workers demonstrated at both laboratory and plant scales that sonic injection (jetting regime) into copper or nickel converters could reduce or eliminate the above hindrances characteristic of PS converting. Since then, in spite of these successes, very little industrial applications have made headway in the converting process of non-ferrous metal mattes on a commercial scale. As part of its operational improvement and energy reduction program (process efficiency), Lonmin Platinum decided to conduct a full scale industrial evaluation of sonic injection using air only to establish if punchless, high efficiency sonic injection was feasible in its small 3.05 × 4.57 m converters (10’ × 15’). A plant trial was run for four weeks in one of its three converters. This paper discusses the plant demonstration with a focus on the experience acquired by Lonmin together with the key learnings from the trials. Reference will also be made to the commercial aspects of a full scale implementation of sonic injection in all three converters in the smelter. INTRODUCTION AND OBJECTIVESAlthough the centennial of the Peirce-Smith (PS) converting process has recently been celebrated (Peirce and Smith, 1909; Southwick, 2009), the technology has essentially not changed much since its inception. PS converting is used extensively in the Cu, Ni and PGM industry to remove iron and sulphur from a molten matte phase. A typical PS converting process would use low pressure air supplied by a blower to bubble air through the molten bath. This bubbling injection regime is inherently inefficient from a process and energy consideration."

Jan 1, 2012

By H. R. Hammond, E. Sadar

Cominco is making substantial savings in secondary breaking by replacing dynamite with a new nitrate-based explosive. Compareo with dynamite. the new explosive, known locally as "Fine NCN," is significantly cheaper, more effective and safer to use. It also works better than prilled NCN, which is unsatisfactory for secondary blasting because of inadequate sensitivity, low strength and awkward handling properties. A simple apparatus has been devised for pulverizing prilled NCN to a fineness practical for effective secondary breaking. Blasting systems using cheap detonating cord for initiation have been developed.

Jan 1, 1966

By David M. Parkes, George E. Davies

"Mathematically, the proposed formula is: ""Human Effectiveness + Technological Improvement = Success in the Nineties"". A brief review is made of geology, level of technology, management and labour situations, and range of production costs in coal producing countries. This comparison shows keen competition for Canadian coals, especially from the People's Republic of China, South Africa and Australia. Domestic competition comes from nuclear energy, hydro-electric generation, natural gas (if permitted) and eastern United States coal.The huge increase in the size and power of surface mining equipment in the last forty years led to modern large-scale open pit mining. While conventional truck and shovel operations will continue to be widely used, more continuous mining and conveying systems will be installed as pits become deeper and haul distances longer. Computer systems will become more sophisticated and their applications more widespread, leading to higher productivity and closer control of all operations and equipment performances and to partial or complete automation of certain operations.The underground revival will be driven by a new generation of mining people, cooperating to produce over 3 million t/y from 300 m longwall faces retreating over 3 km resulting in mine productivities of over 40 tonnes per man shift, as is already achieved in several mines throughout the world. Continuous operation using on-line control system will assist in consistent production with availabilities over 75%."

Jan 1, 1991

By Alfred Guenkel, Kyle Marte, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985 (Borbely, Devuyst, Ettel, Mosoiu & Schitka, 1985). Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. Though it is possible to supply sulphur dioxide (SO2) in either gas or liquid form, the majority of these SO2/air operations use sulphite-based salts as the ‘SO2’ equivalent reducing agent. This is probably due to the lower capital cost, safety concerns with, and availability of liquid SO2. Sodium metabisulphite (SMBS) is commonly employed, and its cost is an order of magnitude higher than that of sulphur. The increased capital expenditures (CAPEX) for a sulphur-burning SO2 gas plant could have a pay-back of less than two years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas inventory. Furthermore, a SO2 gas plant will not trigger the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and Boleo).This paper discusses the different processes which require SO2 as a reducing agent and compares the capital and operational costs of a SO2 gas plant to conventional process alternatives using sulphite-based salts or liquid SO2.The heart of the SO2 gas plant is the sulphur furnace. The most economical way to produce SO2 is by combustion of sulphur in air producing up to 19.5 vol% SO2. Examples of large and small sulphur furnaces are discussed in terms of design, operation, and impacts on operational costs.The SO2 gas produced in a sulphur-burning plant has to be contacted with the liquor to be reduced. The choice of gas-liquid contacting device is important, and two contacting devices are discussed: 1) Gas sparging into the bottom of leach tanks (high, nearly constant, back pressure due to liquid head) and 2) absorption columns (low gas-side pressure drop)."

Jan 1, 2014

By D. G. Macintyre

"Potentially economic stratiform barite-sulphide deposits have recently been discovered in Devonian basinal facies rocks of the Kechika Trough of northeast British Columbia. This new mineral district is over 180 kilometres long and includes nine major occurrences, namely Driftpile Creek, Bear, Mount Alcock, Cirque, Fluke, Pie, Elf, Kwadacha and Sika. The Cirque is the largest known deposit, with reserves of atleast 30 million tonnes averaging 10per cent combined lead-zinc and 47 grams per tonne silver. The footwall rocks for the Cirque and other strati/rom barite-sulphide deposits in the area are rhythmically bedded baritic and pyritic carbonaceous black shales, siliceous argillites and cherts of probable Mid to Late Devonian age. These siliceous rocks overlie a succession of proximal to distal turbidites which are the basinal equivalent of Early to Mid Devonian carbonate reefs to the east. The siliceous facies is overlain by deeper-water black shales of probable Late Devonian to Mississippian age.Preliminary stratigraphic and sedimentological investigations suggest that the strati/arm massive pyrite and bedded barite deposits formed in third-order euxinic basins within a northwest-trending structurally controlled trough which, in the southern part of the district, was bounded by carbonate reefs. The exhalative event, which appears to have been accompanied by synsedimentary faulting, took place during the early stages of a major eastward-directed marine transgression that was probably related to rapid crustal subsidence. Dewatering of metal-enriched shales and subsequent brine discharge along fault zones within the trough, with the exhaled brines accumulating in seafloor depressions, is the mechanism envisaged for formation of the deposits. Convective circulation systems may have been established about the more deep-seated faults, in response to elevated heat flow levels."

Jan 1, 1982

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By Brian C. Maynard

"Blast design is becoming more and more important as industrial limitations change in regard to economical and physical restraints. Certainly there are ways to alter the nature of the blast by using different explosives, various hole sizes and modifying the timing and charging details. However, it is not possible to alter the fabric of the rock mass. Therefore, it is necessary to learn more about the rock mass and its role in the blast design, and the resulting fragmentation. The major determinant in the degree of fragmentation, or lack of it, is proposed to be the inherent fragmentation of the in situ rock mass. A practical method of quantifying the discontinuities existing in the rock mass is presented and discussed. Likewise, the effects of inherent fragmentation on the resulting muckpile are reviewed. Finally, a fragmentation model combining the calculated inherent fragmentation and the Kuzram model is shown using a sample blast.IntroductionIn blasting, discontinuity characteristics (Fig. 1) control the method by which the rock mass will behave. Research carried out by Piteau (1970) showed a number of characteristics important in engineering design and, as proposed, in blasting processess. These included:• the nature of their occurrence (i.e. sets or isolated);• orientation and position in space;• continuity; and• intensity"

Jan 1, 1990

By A. J. Oliver, C. E. O’Neil, I. J. Itzkovitch, V. A. Ettel

A new solvent extraction process for the separation of cobalt, copper and zinc from nickel sulphate process streams has been developed. It involves selective extraction of these elements with a quaternary ammonium thiocyanate dissolved in an aromatic diluent. The chemical principles of this process have been investigated and are described, together with background physico-chemical data relating to the use of this solvent. Long-term testing in a continuous "mini-plant" circuit gave high-purity nickel and cobalt products (Ni/Co —200011 and Co/Ni ~1000/1 respectively).

Jan 1, 1976

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By A. Khan, C. Ciriello

The purpose of this paper is to demonstrate the value of constraint modelling in optimization of mineral processing systems. This will be achieved by first understanding the overall concept of variation and constraints present in any system. Next, the value of using a Constraint Model in optimization is demonstrated through comparison of business cases. The benefit of understanding the severity of constraints and movement of the bottleneck within a mineral processing system will be understood through the use of a case study. Paper will conclude with a summary of all optimization benefits that utilization of a constraint model can bring.

Jan 1, 2015