Search Documents

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By L. Furtenbach, T. Möller

"Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation.This paper outlines the experience from the development, installation and follow-up of liners installed in two 38' x 45' AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the “drop-zone” of the shell liners while installing the liner bolts.One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22' diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38' diameter AG mills. The results from this study are included."

Jan 1, 2012

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995

CHALLENGES TO SCHEDULE/BUDGET Shortage of people (contractors, vendor support, engineering, staff) 2007 projects off the shelf Increase in metals prices Shortage of large tires Reserve increase Size of mine Unskilled labor force Community/government relations Limited access into valley English to Spanish SOLUTION Line 1 Line 2 concurrent construction, EPCM engineering review, advance scheduling Placed line 2 orders earlier Hedged currency, bulk orders Strategic alliances Flexible design Plan Deliveries Training, multiple contractors Engagement Built/upgraded roads Technical translators

May 1, 2010

By J. S. Godard

The mining developments in western Quebec have shown the ores of this district to be more complex in character than was at first expected. When the initial discoveries were made it was thought that the ores would be similar in character to those of Kirkland Lake and Porcupine areas. Developments have since shown that although the ores along the southern margin of the belt are somewhat similar, those within the belt, constituting by far the greater proportion, are vastly different, being complex mixtures of base-metal sulphides carrying values in the precious metals. These mixtures of base-metal sulphides of copper, zinc, and iron, present several problems to the metallurgist, especially in their concentration into marketable products. For the purpose .of this paper the following classification may be made of the ores of the district. Group I. - Milling Ores: (a) Ores in which~ arsenopyrite is the predominating sulphide. In this class of ore the gold occurs in fractures in the quartz and is associated to a lesser extent with the arsenopyrite and pyrite. Examples of this class of ore are the Granada, south of Pelletier lake, and the O'Brien and the Thompson in Cadillac township. (b) Ores in which iron pyrite is the predominating sulphide and gold is the valuable constituent. This may also be classed as a concentrating ore-Group III.

Jan 1, 1928

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By R. D. Prettie

Wood preservation may be defined as the art of protecting wood from decay. In its broadest sense, however, it includes a much wider field. It might be more properly de-fined as the art of protecting wood from destructive agents, such as decay, insects, marine borers, mechanical wear, etc. The earliest data on record for the preservation of organic bodies is found in Egyptian manuscripts. The bodies which we call mummies were impregnated with antiseptics, of which the principal were natrum (sodium sesqui-carbonate), sodium chloride, and sodium sulphate. After being steeped in the solution, they were subjected to either a boiling or baking process in a bituminous preparation. The first attempts in Europe to preserve timber were made by the Greeks and Romans. They extracted essential oils from the juniper and cypress trees, and either rubbed these oils into the wood they wished to preserve, or bored thousands of small holes in the wood and poured the preservative oil into the holes. The famous statues of Jupiter and Diana were carved out of wood. The ceremony of pouring in the preservative oil by the High Priests was a religious pageant of great importance, of which there are many records.

Jan 1, 1926

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By J. R. Welsh, D. J. Palmer, O. M. G. Newman

"The use of calcine for selective zinc precipitation requires specialist knowledge to achieve satisfactory flowsheet design. Calcine from the bed of a fluid roaster is preferred, and factors such as the size distribution of ground calcine, the stoichiometric ratio of the calcine precipitant to the initial dissolved zinc concentration and the moisture content of the resultant filter cake are parameters which require critical attention. Extensive testing in a fully-integrated electrolytic zinc plant pilot plant has demonstrated that properly designed selective zinc precipitation plants using calcine as the precipitant are reliable operating units.The advantages of using calcine instead of limestone for selective zinc precipitation include a decreased cost of reagents, as well as avoiding the formation of by-product gypsum.Process simulation modelling has demonstrated that the use of calcine in this context has widespread application in the design of zinc plants with superior impurity and water balance control characteristics. A particularly powerful approach involves closed circuit washing. In this mode, filtrate from the selective zinc precipitation step is used to wash a zinc plant residue such as jarosite, and the resulting filtrate is returned to the selective zinc precipitation section. IntroductionThe Selective Zinc Precipitation (SZP) Process, developed and patented by the Electrolytic Zinc Company of Australasia Limited (EZ) may be used to achieve simultaneously, water balance and impurity control in an electrolytic zinc plantO,2). Impurities which may be controlled by the SZP process include chlorine, magnesium, manganese, potassium and sodium.In the SZP process, basic zinc sulphate is precipitated from a zinc sulphate solution by either limestone, lime or a compound containing zinc oxide, usually calcined zinc sulphide concentrate (calcine) or alternatively zinc oxide fume .The solids containing basic zinc sulphate are separated, typically, by filtration and returned to the zinc plant circuit as a neutralizing agent. The zinc depleted solution can either be discarded, or used to wash residues, thereby achieving water balance and impurity control (Fig. I)."

Jan 1, 1988

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By R. Wirth, B. Orberger, C. Wagner, A. Tudryn, B. Baptiste, S. Miska, Université Paris-Sud

Banded iron formations (BIFs) comprise complex textures and mineralogy, which result from fluid-rock interactions related to high and low temperature alteration. The initial iron oxy hydroxide mineralogy and associated phases such as carbonates, quartz, apatite and phyllosilicates were transformed leading to an upgrading of these BIFs into the world’s largest source of iron ore. In low-grade BIFs, a large part of the iron is related to micro- and nano- metric iron-bearing inclusions within micrometric quartz and/or carbonates (mainly dolomite). We studied laminated jaspilitic BIF samples from a drill core containing 26.71 wt.% total iron, 0.2 wt.% SiO2, 0.32 wt.% MnO, 15.46 wt.% MgO, 22.32 wt.% CaO, 0.09 wt.% P2O5, < 0.05 wt.% Al2O3, 0.15 wt.% H2O and 34.08 wt.% CO2 (Aguas Claras Mine, Quadrilatero Ferrifero, Brazil). Bright rose coloured dolomite and quartz bands alternate with massive specular hematite bands. Raman spectroscopy, X-ray diffraction and FIB-TEM analyses reveal that the micro- and nanometric inclusions in dolomite are mainly hematite and minor goethite, partly occurring as clusters in voids. Curie Balance analyses were carried out at different heating steps and temperatures on whole rock samples and a synthetic mix of decarbonated sample and pure dolomite. X-ray diffraction on the products of the heating experiments shows that that hematite is stable and new phases: magnesioferrite (MgFe2O4), lime (CaO), periclase (MgO), portlandite (Ca(OH)2) and srebrodoskite (Ca2Fe2O5) were formed between 680°C and 920°C. These finding gives hints to optimizing the beneficiation process, as the presence of hydroxyl ions bearing goethite micro- and nanoinclusions lowers the sintering temperature. Prior separation of coarse hematite and barren dolomite and quartz, followed by lower temperature sintering of the inclusionbearing dolomite/quartz leads to transformations into phases with higher magnetic susceptibilities (such as hematite and magnesioferrite). The entire Fe and Fe/Mg oxide feed (the priorly separated fraction added to the sintered fraction) can then pass through wet-high intensity magnetic separation after crushing.

Jan 1, 2016

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By R. Matusewicz, A. Kaye

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in non-ferrous applications, including the processing of lead and zinc primary concentrates and secondary (post-consumer) materials. TSL is highly flexible and efficient, and is one of the few technologies which can process primary and secondary feeds, and use varying fuels, to deliver high recoveries and excellent environmental performance. With the recent high value of both lead and zinc, and an escalating awareness of the sustainable use of resources, focus on the processing of secondary feed material sources has surged. Ausmelt Technology has proven to be well suited to the economic recovery of values, with twenty-two (22) Ausmelt furnaces processing lead and zinc bearing feed sources now in operation, under design or construction. This paper describes Ausmelt&apos;s progress in the fields of lead and zinc processing, and developments in new processing areas such as EAF dust processing and linking to innovative hydrometallurgical technology. Ausmelt has recently committed to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This project is due for start up in the first quarter of 2008.

Jan 1, 2008

By G. Barr

"The Polymetallic Twin Metals Project deposits in Northern Minnesota are being developed by Twin Metals Minnesota. Amongst the flowsheet alternatives being examined at a prefeasibility study level is one involving flotation of a bulk concentrate followed by high temperature autoclaving of the concentrate using the PlatsolTM Process to solubilize all the valuable metals in the concentrate (Cu, Ni, Pt, Pd and Au). Autoclave operating conditions have been established in which recoveries of all the pay metals are in the 92 to 99% range, and the autoclave residence time has been reduced to an hour. The stability of the precious metals in solution after autoclaving has been assessed, as well as the impact of internally recycling process liquors to the feed to the autoclave.INTRODUCTIONPlatinum group metals (PGMs; platinum, palladium, rhodium, ruthenium, iridium and osmium) are traditionally recovered from their ores by production of a high-grade concentrate by flotation and/or gravity concentration followed by smelting of the concentrate. Concentrates are smelted to remove nonsulphide minerals and converted to remove iron and sulphur. The resulting high PGM grade matte is processed hydrometallurgically to leach the base metals, leaving a residue with a very high grade (20-40%) PGM concentrate for final refining to individual PGMs. Due to the complexity of this process and its high capital cost, this process can only be applied economically to high grade PGM ores. Lower grade PGM concentrates might be accepted as copper and nickel concentrates but may not yield attractive payment terms for the PGMs. The mineralized Duluth Gabbro region of Minnesota hosts several low grade base and PGM deposits and Twin Metals Minnesota is working to develop the Twin Metals Project deposits. Earlier studies at both pre-feasibility and feasibility level, by other mining companies, have failed to yield an economically viable project based on the traditional process. It is possible to produce a saleable copper concentrate from these ores, but economic recovery of nickel and PGMs into saleable concentrates proved elusive.In the late 1990’s and early 2000’s the Platsol™ process was developed at SGS in Lakefield, Ontario (at the time Lakefield Research Limited) for the NorthMet deposit (also within the Duluth Gabbro) owned by PolyMet Mining. The process developed was a high temperature chloride-assisted pressure oxidation process capable of dissolving simultaneously the base metals (Cu, Ni, Co, Zn), gold and the PGMs."

Jan 1, 2012

By Balmer Neilly

FOR some reason or other, Mine Taxation has never been a popular subject for discussion in meetings of this kind, and it has never received the study and consideration its importance demanded. By way of explanation, two reasons may be suggested. In the first place, the computation, adjustment, and final payment of taxes, have been looked upon in most cases as a Head Office chore. Secondly, since taxes represent an uncontrollable cost item, they have been treated as an added rather than an inclusive factor in calculating unit costs. Perhaps because I am half Irish, and therefore resent taxation of all kinds, perhaps because I am half Scotch, and am therefore concerned with the results, I have always taken a keen interest in this subject. Moreover, by some peculiar set of circumstances, I have been a participating party in many, perhaps I can say most, of the discussions on this subject that have taken place between the Governments and the representatives of this industry during the past thirty years. Looking backward, certain very definite impressions remain. Political considerations have never had any part in these discussions. Views have been exchanged upon the frankest possible basis, and, when we disagreed on some particular detail, we agreed to disagree, and followed through in harmony and? good faith. We, as an industry, have refrained from importuning and fault finding in ways that might be considered as petty or selfish, and it is only upon occasions such as this, where conditions necessitate action, that we lay our troubles before the powers that be. The Ontario Mining Tax Act was drafted by men who were earnest and practical as to purpose, and that Act has stood the test of time. It is, in. truth, a mode! Act, for it has been copied in its general clauses by both Quebec and the Dominion of Canada. We all know that, when a machine is running smoothly, we should leave it alone. The same is true of a well designed, easily applicable, taxation measure, and our present difficulty with respect to this Act arises out of an amendment made in 1916. In that year, you will remember, the Dominion imposed a wartime Income Tax Act. It was described as a wartime necessity and it was intimated t:1 at with the end of hostilities its application would be restricted and finally cancelled. The rate of taxation was modest, and when the Ontario Government was asked that the Dominion Income Tax be allowed as a deductible item, they readily acquiesced. This was looked upon as a temporary arrangement.

Jan 1, 1943

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964