Search Documents

By Carrasco .. P. J. A., R. Parada, I. Saavedra, F. Parada, R. Parra, E. Balladares

In most of the smelters, the management of flue dust has a double objective: the control of minor elements in the anodes and the management of volatiles compounds that can cause contamination due to fugitive gas emissions. This is a special concern when high content of Va elements (As, Sb & Bi) are present in concentrates. We present the results of the experimental study to prove the principle of a novel process that recovers, via volatilization, the As, Sb and Bi in the flue dust as gaseous sulfides, due to a previous sulfidization. In the case of as control any further classical treatment for its stabilization is possible from the gas. The clean calcine can be returned to the smelter avoiding any concentration of these minor elements in the circuit. This process is now tested at pilot scale and shows better indices on carbon footprint than the classical hydrometallurgical process for flue dust.

Jan 1, 2011

By M. Sengupta

International trade in minerals plays a very important role in the economic growth of many nations. Several less developed countries a1•e heavily dependent on their mineral exports for earning foreign exchange, which is needed for industrialization. Mineral exporting nations experience many problems in international mineral markets; the most important are tariff barriers, deteriorating terms of trade, instability in metal prices, etc. The formation of international mineral cartels to raise prices can be successful only to a limited extent and only for a short period of time.

Jan 1, 1976

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By J. R. Goode

ABSTRACT Aurora Energy Ltd. is considering a 10,000 t/d process plant to produce 97 million lb (43,998,460 kg) of U3O8 over a 17-year project from uranium deposits in coastal Labrador. This paper summarizes the test work, mostly done by SGS Mineral Services in Lakefield, Ontario, and the economic studies supporting flowsheet selection. The proposed flowsheet includes semi-autogenous grinding (SAG) and ball milling, acid leaching using air/SO2 as an oxidant, and resin-in-pulp (RIP) extraction of uranium from the leached slurry. Other unit operations examined include ore sorting, heap leaching, liquid- solid separation, solvent extraction, and nanofiltration for eluate upgrading. We also review the extensive environmental test work and studies that were completed.

Jan 1, 2012

By D. C. R. Espinosa, P. Aliprandini, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel and cobalt are the main value metals in nickel laterite ore. Cyanex 272 is an extractant used to separate nickel from cobalt present in leach solutions. Previous studies demonstrated the extraction of cobalt, magnesium and manganese at pH 5 using Cyanex 272 as extractant, while nickel remained in aqueous solution. However, it is difficult to separate cobalt from a solution containing magnesium and manganese. One possibility to change the metals’ behavior during the solvent extraction process is to change the mixture of extractants used. In order to study the solvent extraction of cobalt from a solution containing manganese, magnesium and nickel, a mixture of two extractants was investigated. Cyanex 272 (CY) and Versatic 10 (VC) were selected as extractants in the organic phase. The extractant concentrations used were: 20% CY; 15% CY, 5% VC; 10% CY, 10% VC; 5% CY, 15% VC; and 20% VC. In all cases, kerosene was used as a diluent, at 80 vol%. The synthetic leach solution used in this study was prepared according to the composition of a typical nickel laterite leach solution. The pH value of the solution used was 5, and the aqueous/organic ratio used in solvent extraction testwork was 1/1. The study has shown that the composition of the organic extractant mixture did not increase cobalt separation.INTRODUCTION Sulfide and laterite deposits are the main sources of nickel. However, production from nickel sulfide ores has been decreasing over the years, relatively speaking, increasing the focus on the exploitation of laterite nickel ores (McDonald & Whittington, 2008). Laterite ore deposits are found in tropical and subtropical regions. A characteristic of laterite ores is the presence of a complex and heterogeneous mixture of metals (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011; Georgiou & Papangelakis, 1998; Gupta, 2003; Kesler & Simon, 2015; Moskalyk & Alfantazi, 2002; Oliveira, 1990). Nickel concentrations in laterite ores are typically 1–2% (Dalvi, Bacon, & Osborne, 2004)."

Jan 1, 2017

By P. West-Sells, B. Wassink, N. Fisher

Gold leaching from a commercial cyanide-amenable gold ore was studied at 25°C using sodium bisulfide-hydrogen sulfide solutions containing elemental sulfur. Gold extraction from the ore using 0.55 M NaSH, 4.1 atm (60 PSI) H2S, 1 g/L S8 and 26% solids by weight was about as good as the best extraction obtained by cyanidation. Maximum extraction was achieved in roughly 48 hours. Sulfur dissolves in the bisulfide solutions to form a mixture of polysulfides. Simple speciation calculations indicate that gold solubility as bisulfide complexes should be roughly ten times higher than in the absence of added zerovalent sulfur. The principal bisulfide complex is believed to be [Au(HS)2]-. Gold dissolution is favoured by increasing HS- concentration and by increasing H25 pressure. Polysulfide complexes of gold are also likely to be formed, and may contribute substantially to gold leaching. Two experiments using pure gold were also performed. Up to 100 mg/L gold was dissolved in 140 hours using 0.55 M NaSH, 1 g/L added elemental sulfur and 6.2 atm H2S.

Jan 1, 2005

"Le présent article porte sur la diminution des rejets de concentrateurs produits durant l’exploitation et le traitement des minerais métalliques.Le minerai dilué envoyé au traitement a, très souvent, un certain pourcentage du stérile qui affecte directement la rentabilité des opérations souterraines et amplifie l’impact négatif sur l’environnement. Les essais de la séparation du stérile et du minerai effectués en milieu dense sur quelques types de la minéralisation d’or, ont démontré les deux possibilités qu’offre cette technique:• Dans le cas d’un minerai riche, il a été possible de séparer la part importante du toutvenant (minerai dilué contenant le minerai et le stérile) provenant de la dilution, tout en ayant un taux de récupération élevé (supérieur à 96%).• Dans le cas d’un minerai ayant une teneur sub-économique à cause d’une dilution importante, il est possible de produire un concentré ayant une teneur économique à l’entrée de l’usine de traitement, en éliminant une partie du tout-venant.En plus la séparation du stérile peut accroître, en outre, la rentabilité de l’exploitation minière, car le fait d’éliminer la partie de stérile le plus tôt possible diminue certains coûts (transport, traitement et autres). On conclue que la pré-concentration du minerai (séparation du stérile et du minerai) est probablement une seule solution actuellement étudiée qui diminue l’impact environnemental de la mine, sans avoir des conséquences négatives sur la rentabilité de l’exploitation souterraine."

Jan 1, 1997

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By S. Kelebek, U. Demir, T. C. H. Richards, E. Koss

"Laboratory-scale tests were carried out to investigate the response of a high-grade (~143 g/tonne) well-liberated gold ore to flotation using two collector types. Octyl and amyl xanthates, representing conventional types of collectors, were tested against an n-octanoic and hexanoic acids under moderate and high redox potential conditions. The latter was based upon a suggestion in literature that monocarboxylic acids are able to adsorb onto the surface of gold at redox potentials near 600 mV (SCE). This investigation did not demonstrate that these carboxylic acids could function as collectors for gold in real ores. In fact, they appear to have slightly depressed gold. However, the results demonstrated that octyl and amyl xanthates acted as highly effective gold collectors for this ore and that an increase in the collector dosage led to an increase in recovery for all mean particle sizes. In some tests, gold recoveries of around 95% were attainable in concentrates with grades around 6 kg/tonne, indicating that xanthate flotation remains a viable means of concentrating gold even at coarse grain sizes. Various aspects of the process such as grade-recovery performance and recovery by size are discussed.INTRODUCTION Three methods are used for the recovery of gold in mineral processing, either alone or in combination: gravity concentration, cyanidation and flotation. Gold occurs as a by-product in some ores together with platinum group metals and as the primary metal in other ores in the form of native gold and electrum, which are alloys of gold, silver and minor amounts of copper. Flotation is a viable method for recovering liberated gold where the gold is visible under an optical microscope (greater than 1 µm in size) and where the attachment of gold grains is not prevented due to bubble loading by competing minerals. It is generally known that grains finer than 150 µm in size will float with most collectors."

Jan 1, 2017

By A. Mazhary

"Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. In order to shed some light on the matter, this article looks at two different gold deposits that were examined using X-ray Fluorescence, Electromagnetic and X-ray Transmission sensors. The heterogeneity of each sample is measured based on the assay results of each particle and is related to its sortability. Multivariate linear regression analysis was also performed on the XRF results to find potential proxy elements for detecting gold. The results from these deposits were varied and each sample showed different levels of sortability. While both X-ray sensors proved efficient for different deposits, the electromagnetic sensor failed to produce any promising results. Despite unsatisfactory result for one sample, this technology can have significant advantages in terms of lowering the operational costs and improving head grades and recoveries providing that the deposit is amenable to such separation methods. Therefore, it is important to mention that sensor-based ore sorting is ore and sensor dependent, and as a result, it cannot be applied and be beneficial to all deposits. Therefore, amenability tests are required in order to examine the potential for sensor-based ore sorting before one can reject the idea.INTRODUCTION Although sensor-based ore sorting has gained significant attention recently, sorting gold deposits still face a high level of skepticism by gold mining companies. Except for a few cases presented previously, no new case studies have been published. Previously, mines such as Kloof Gold Mine in South Africa used an optical sorter to sort their waste stockpile in 2003–2004 (Von Ketelhodt, 2009) and then again in 2009 (Von Ketelhodt, Falcon, & Falcon, 2011). More recently, Coeur Operations utilized an XRT sorter for their Kensington Mine in Alaska (Lasley, 2014) and also Anglo-American Platinum used an XRF sorter to pre-concentrate Platinum Group Metals through an algorithm that used chrome, copper and nickel as proxies (Rule, Fouchee, & Swart, 2015)."

Jan 1, 2017

By M. F. Goudge

MAGNESIA refractories and magnesium metal are both essential war commodities. The need for magnesium, which had just made its debut as a commercial metal a few years before the outbreak of the present war, is widely known because this new and valuable light metal has already received much publicity. Less widely known but equally important in the war effort are magnesia refractories. They are indispensable to the efficient functioning of the great metallurgical plants producing steel, nickel, copper, and other metals, where, because of their resistance to extreme high temperature and chemical attack, they are used in lining the furnaces, which are operated at a white heat. The demand for refractories in the metallurgical industries rose rapidly upon the outbreak of war, and now, in consequence of the continued great expansion under way in the manufacture of steel, nickel, copper, and other metals, the need for magnesia is greater than ever. Since 1915, part of the Canadian requirements of basic refractories has been supplied from the deposits of magnesitic dolomite in Argenteuil county, Quebec. The products from these deposits are excellent for many uses, but the magnesitic dolomite has too high a content of silica and lime to be used in making a type of magnesia brick required in nickel converters, and in the roofs of reverberatory furnaces used in the copper and steel industries. There is now a large and growing demand in Canada for bricks and shapes for these uses. This demand has always been supplied from the United States. Makers of these products in the United States, in turn, formerly imported most of the necessary high-grade, dead-burned magnesia from Austria and Manchuria. Not only are these sources closed, but refractory chrome ore from the Philippines is no longer available and chrome refractories may have to be in large part replaced by magnesia.

Jan 1, 1942

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By Mingxia Liu, Hao Li, Qi Liu

"Laboratory batch flotation tests were carried out on fine (-20 µm) hematite to investigate the non-polar oil’s influences when sodium oleate, octyl hydroxamic acid, or oleyl hydroxamic acid were used as a collector. Batch flotation tests were performed with artificial mixed minerals (hematite:quartz = 1:1) under natural pH condition and kerosene was utilized as the model oil. The experimental results showed that kerosene emulsion behaved differently when used in conjunction with the three collectors. Kerosene helped improve the flotation when sodium oleate or oleyl hydroxamic acid was used as a collector. Nevertheless, it reduced concentrate weight yield, grade and recovery to a noticeable extent when octyl hydroxamic acid was used as a collector, especially at low dosages. In addition, single hematite batch flotation kinetics tests coupled with water recovery measurement were carried out to study the role of kerosene at different collector dosages. It was observed that water drainage and the resulting froth destabilization by kerosene was dominant at low collector dosages, especially in the flotation using octyl hydroxamic acid. At higher collector dosages, the water drainage and froth destabilization effect by kerosene was possibly counter-balanced by the higher hematite hydrophobicity and bubble surface tension gradient, which led to more stable froth layer.INTRODUCTION The minerals industry is facing a steady decline in ore grade, compounded by increasing complexity of mineral dissemination. As a result, the ore has to be ground sufficiently fine to have a suitable degree of mineral liberation, which produces large percentages of fine and ultrafine particles outside of optimal size range for ore dressing. Due to the unique characteristics of fine particles, i.e., small mass, high specific surface area, and problems such as increased solubility of complex minerals (Finkelstein, 1997; Finkelstein & Allison, 1976; Fornasiero & Ralston, 2005), high reagent consumption, fast surface oxidation in the case of sulfides (Collins & Read, 1971; Klassen & Mokrousov, 1963), severe particle entrainment (Subrahmanyam & Forssberg, 1988; Warren, 1984), low flotation rates (Glembotsky, 1953; Philippoff, 1952; Ye & Miller, 1988), slime coating (T. K. Mitchell et al., 2005; Parsonage, 1984), etc., flotation performance of these finely ground ores is very poor in terms of low concentrate grade and recovery."

Jan 1, 2017

The primary steel industry of the Prairie Provinces consists essentially of three companies whose total annual melting capacity, as of January 1, 1963, was 333,000 net tons. These companies have steel rolling facilities. In addition, there are five other companies producing steel castings by melting scrap in electric furnaces which, with the plants having rolling facilities, gives a total annual furnace melting capacity of 380,000 tons. Since 1954, the annual production of steel ingots and castings has ranged from a low of 66,588 tons, in 1954, to a high of 211,138 tons in 1961. The present facilities on the Prairies for making steel ingots from scrap, and rolling them to produce light merchant mill products, appear to be sufficient for many years ahead. Steel scrap, as electric furnace feed to make steel ingots for the present line of products, will probably continue to be available at reasonable prices either on the Prairies or from the north-central United States. It is recognized, however, that residual elements in scrap may be-come of greater significance and necessitate more rigid control of scrap quality.

Jan 1, 1963

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018