Search Documents

In order to understand the technique, basic theoretical principles of radiation emission and in- strumentation theory are reviewed. Methods of surveying, reduction of data and interpretation are outlined. Other applications of the technique (e.g. in airborne geological mapping), as well as its specific use in uranium exploration, are discussed. By means of case history-type examples the successful applicant of gamma-ray spectrometry, as a tool in Australian mineral search, is demonstrated.

Jan 1, 1969

The paper describes the design of the dilute medium and medium recovery circuits installed at the coal preparation plants at the Cornwall Coal Company's Fingal Mine, and the BP Coal Australia's Howick Mine. These circuits maximize the use of clarified water for rinsing to improve the mass transfer of adhering medium from the coal surface into the carrying liquid, and have been combined with the use of a two stage magnetic separator. The separator utilizes a conventional concurrent first stage and a counter-rotation second stage. This combination results in high medium recoveries during both normal operation, and start up and shut down phases when large quantities of medium can be lost from a conventional circuit. Overall losses using this circuit have been estimated to be, 200g/t, over a twelve month period. Further advantages in plant operation are also obtained, especially steady operating conditions in the centre-tube pump tank, lower slimes contamination of the product, and lower quantities of non magnetics trapped in the separator concentrates. The techniques are particularly suited to incorporation in circuits treating coals containing high percentages of sticky and difficult clays, as are found in the Walloon coal measures.

Jan 1, 1987

By Merry N, Cocks T

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and Composition.

Jan 1, 1995

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

The South Junction deposit of St Barbara Mines Limited was discovered in 1989 by the geologists of Ross Atkins Mining.The deposit occurs in the lower part of the Gabanintha Formation of the Lukes Creek Group in the Mt Magnet -Meekatharra greenstone belt. Country rock is predominantly talc-chlorite schist. Gold mineralisation is associated with north-south shear zones, quartz-carbonate-fuchsite alteration of the ultramafic rocks and in particular close to deeply weathered quartz-albite porphyry. For a detailed description of the geology of the South Junction Deposit see Fiala (1992).

Jan 1, 1993

By Kanchibolta S. S, Brunton I, Tapia-Vergara F

The Split digital image processing system has been implemented in three Australian mines for analysing the size distribution of rocks from the images taken from muckpiles, conveyor belts and tipping trucks. This paper presents an overview of t

Jan 1, 1998

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By Shoobridge PH

Operating difficulties during 1977 with the Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at their Cockle Creek zinc-lead smelter were found to be caused by premature softening of sinter in the upper shaft of the furnace. This soft- ening was shown to be a consequence of raw materials and operating policies which led to unusually high levels of both lead and silica in a sinter of low basicity. A programme of softening tests and micro-examination of a range of sinters established that premature softening occurred when lead and silica increased to the point where a lead-calcium silicate with a low lime content became the major continuous phase in the sinter. This information was used to define a range of compositions which kept the softening temperature acceptably high for furnace operations.

Jan 1, 1978

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

By Nilmani M, Malone J, Taylor RN, Floyd JM, Gray NB, Fountain CR

CSIRO staff and University of Melbourne staff and students collaborated in an intense programme of investigation on the CSIRO 50 kg Sirosmelt pilot plant.In two days of operation copper matte converting and zinc slag fuming trials were performed, whilst investigation of the process dynamics and process chemistry was carried out. This exercise is an example of the techniques available for process evaluation, which can rapidly advance the understanding of pyrometallurgical operations by use of a team approach covering a wide range of experiments.

Jan 1, 1985

By Wymer DG

The concept of hydro power in deep mines is based on the exploitation of the hydrostatic head that can be gained as refrigerated cooling water descends in shaft pipe columns from the surface, to provide hydraulic power for machines at the working face. This paper describes the work done on two important aspects of the controlled distribu-tion of the high pressure water within a mine, namely the control of pressure under normal operating conditions, and the control of flow in an emergency situation following a pipe breakage. Suitable methods of control have been determined using theoretical techniques to model the steady and unsteady flow behaviour of the water in the pipeline, and taking into consideration the environmental constraints on the types of control devices that can be used. The preferred approach is one in which the high pressure water itself is used as the control medium. The control valves themselves can be fairly conventional in design, but in the case of pipe break protection it is shown that a less conventional approach based on the use of a hydraulic fuse gives improved control performance.

Jan 1, 1985

Studies of Theological effects in grinding hold promise for improving this energy-intensive process. Six surveys of the Hellyer ball mill were conducted. The stream and sizing data from these surveys were balanced by JKMbal to compare the mill

Jan 1, 1994

Methods for ore reserve estimation are classified. The amount of information needed to asses ore reserves is analysed. Reference is made to gold sampling. Consideration is given to nugget effects and ore reserve estimation procedures where they are significant. Computer methods are discussed

Jan 1, 1997

An intensive safety campaign at Mount Isa Mines Limited from 1956 to 1966 saw the lost time accident frequency rate fall to half its original level. A review of the safety programme was carried out in 1967 and in 1968 the Five Point Safety System was introduced. The seven years since its introduction have been years of significant achievement both in production and safety. Improving safety is a fundamental part of Mount Isa Mines Limited's policy and this system has been a major tool in implementing that policy. To be successful personnel need to be prepared and trained for its introduction and subsequently counselled on its use. A carefully prepared programme is required to phase in various aspects of the system and to make use of complementary steps. The system has been a success and it is anticipated that the continued drive to improve the use of principles of the system will further improve safety. It is hoped that this paper will be of value to those personnel concerned with industrial safety in Australia.

Jan 1, 1975

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

By Dunn P. G

The copper ore reserves at the Chuquicamata mine were re-estimated during March to June 1994, as part of a comprehensive audit of the mine's overall short- and long-term planning. The basic principles essential to all ore reserve estimates were implemented viz: 1. A detailed study of the geology, in this case particularly of the orientations of structural features of copper mineralisation and the subdivision of the orebody into geologically homogeneous sections, 2. the use of both drillhole and blasthole data sets, 3. statistical and geostatistical analyses of both data sets to model anisotropic spatial structures for all the geologically homogeneous sections, 4. block kriging using both data sets individually; and 5. a comprehensive validation of the block valuations to confirm the absence of global and conditional biases and to quantify the actual improvement achieved in the overall quality of the estimates compared to those executed on earlier techniques.

Jan 1, 1995

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996