Search Documents

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By R. V. Smith

The theoretical background for calculating friction factors for flow in gas wells by two methods is presented. The first method, requiring pressures, temperatures and specific volumes of the flowing fluids at various depths in the well bore, shows how the mechanical-energy-balance equation for vertical flow may be graphically integrated over the actual path of the expansion of the fluid in the well. Thus, assumptions regarding the effective temperature and effective compressibility of the fluid in the well are avoided. The second method presents an equation derived on a basis of the assumptions that both the temperature and the compressibility are fixed at constant effective values throughout the flowing column of gas. The second method provides a convenient and practical means of calculating friction factors for gas wells and lends itself readily to the problem of calculating subsurface pressures in a flowing gas well. The application of both methods to actual test data taken on a flowing gas well is illustrated in the paper. INTRODUCTION As friction factors for the producing strings of flowing gas wells cannot be measured directly and must be calculated from flow-test data, study of the methods of arriving at friction factors is a necessary adjunct to understanding the characteristics of flow in gas wells. There are two methods of calculating friction factors for gas wells; they differ from one another mainly in the treatment of the path of expansion of the fluid in the well. In the flowing well, the energy consumed in lifting the fluid from the bottom to the top of the well, overcoming the friction between the moving fluid and the pipe walls, and increasing the velocity of the fluid as it flows up the producing string is supplied by expansion of the flowing fluid. The available energy is determined by the expansion of the fluid that follows a path determined by conditions of temperature, compressibility and phase changes of the fluid during the expansion. A means of evaluating the available energy in a flowing gas well and determining the proportion of the available energy used in lifting the gas, overcoming friction, and increasing the velocity of flow is developed in this report. Knowing how much energy is consumed in overcoming friction makes it possible to calculate friction factors for given flow rates in given sizes of pipes in wells. Friction coefficients, as used in this report, are dimension- less proportionality multipliers used in the flow equations to satisfy the equality between the terms of the equation. The square root of the reciprocal of the friction coefficient is termed the friction factor. It has been known for many years that friction factors may be computed directly from mathematical formulas based on certain assumptions regarding the temperature and compressibility of the moving fluid in a well. A general equation is presented in this report without assumptions for vertical flow of fluids and a conventional-type equation is derived on the basis of assumptions that fix the temperature and compressibility at constant values. Accurate pressures at the sand faces in wells are required in the method of determining the productivity of gas wells, as outlined by Rawlins and Schellhardt1 in Bureau of Mines Monograph 7. Where measurements are not made with subsurface-pressure gauge; or static gas columns are unavailable, flowing pressures customarily are calculated at the sand face in the well by the use of the well-known Weymouth formula1. Natural gas engineers have realized that errors introduced by the use of friction factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; they also know that such factors are important considerations in testing large-capacity gas wells. Accordingly. present research on the productivity of gas wells at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla., is being directed toward measurement of the pressure loss due to friction in flowing gas wells. It is beyond the scope of this report to show how friction factors vary with rate of flow and in pipes of different diameters, as it is intended only to develop and illustrate the use of mathematical expressions for calculating friction factors from flow-test data. The equations presented apply only to turbulent flow in circular pipes. ENERGY RELATIONS FOR FLOW OF FLUIDS2 The concept of conservation of energy is usually the basis of any study of fluid flow through vertical pipes as in gas wells, horizontal pipe lines, or orifices. In deriving equations, the following symbols are used:

Jan 1, 1950

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for, this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators 1.2.1 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By David B. Brooks, William A. Wallace, James R. Dunn

As the conflict between the mineral industry and preservationists steadily increases, it becomes urgent to determine as precisely as possible the costs of developing vs. not developing our domestic mineral resources so that enlightened mineral policy decisions can be made. A simple discounted cash flow equation is suggested as an approach to assigning a public-interest dollar value to mineral resources. Present value of a piece of land underlain by a mineral resource is taken as equal to the discounted cash flow derived from the resource corrected for present and future surface land values. The equation is effective as a base for mineral aggregate resource planning for metropolitan areas if transportation cost differences are substituted into the cash flow component. Suitably modified, the equation can be fitted readily into an existing computer simulation program for aggregate mineral resource planning in metropolitan areas. However, because of the lack of accurate input, the equation is less effective for other mineral commodities such as base metals and coal. Nevertheless, within a somewhat philosophical context, the equation still has utility and is effective in defining the problem of public interest values for minerals other than mineral aggregates.

Jan 1, 1972

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By Joseph H. Allen

In the old Kentucky reports, made by the Survey of which Prof. Owen was director, the veins of the Western Kentucky coal-field were numbered from 1 up to 12. Later Prof. Shaler used letters, beginning at the top. For instance, Owen's 12 is Shaler's A.

Jan 1, 1888

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By S. Maemura

Miike Colliery of Mitsui Coal Mining Company, the biggest and oldest coal mine in Japan, is producing a quarter of the national coal production, about 5.2 million tons of clean coal annually and almost a half of which is now being mined under the "slicing Mining System". The slicing system is a mining method to mine a thick coal seam dividing it into two faces, upper and lower. Its history started nearly 20 years ago. However, the all-around modernization of this system has made little progress up to recent years, while mining methods for single longwall faces has made a remarkable progress together with the improvements in mining machineries, self advancing supports and so on. The reason was that the tremendous difference in adaptabilities of mechanized face equipments existing between the upper and lower faces has made it very difficult to increase the total production capacity of slicing system. After our persistent study for seventeen years, we have recently realized successfully the quite satisfactory slicing system, applying the combination of shield type self advancing supports and double ranging drum cutter at both faces. We are now fully convinced of that the high efficient, quite safe and improved slicing system has been basically established for the present. This paper intends to brief the transition on the combination of self advancing supports and mining machines, its results and further to detail the development of shield type self advancing support for upper face and artificial roof material which shall be the key point to be successful in full mechanization of slicing faces.

Jan 1, 1976

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By Michael A. Devane, Neil Duncan

Inclines and tunnels can extend from ground surface to considerable depths traversing a wide range of lithologies. The strata encountered may be affected by loosening and induced stresses at different locations along the route. It is suggested that Phase I of the pre- driving assessment process should include study of the geology, hydrogeology, rock material and rock mass characteristics. A rock mass disruption factor is used to express the ratio of the unconfined strength of intact rock material to the unconfined strength of in situ rock mass. It is suggested that there is a relationship between in situ (secondary) permeability values and the disruption factor, since the permeability of the rock mass is governed by parameters which influence strength. In Phase I1 of the pre-driving assessment, consideration should be given to the prediction of primary loosening which results largely from disturbances to the rock mass arising from the driving process. Also in Phase 11, preliminary assessments are made of the effects of induced stresses and of the geodurability characteristics of the rocks. In Phase 111, the mechanics of various secondary loosening pro- cesses are considered along with their relevance to estimates of stand up time and support requirements. Yield-line analysis is introduced for the study of plastic and brittle type bending deformations. Stand up time and support characteristics are also assessed. In Phase IV, the effects of induced stresses are analysed. It is suggested that even for broken rock in the Yield Zone, the rock mass disruption factor may not often increase above lo which is equivalent to an in situ permeability of 10-1 m/s.

Jan 1, 1983

By Robert E. Green, Edmund G. Henneke

The velocities of the three possible modes of elastic wave propagation have been calculated for single-crystal copper at 1-deg intervals throughout the standard stereographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy flux and specimen axes are presented as arrows drawn on stereographic projections. The orientation factors associated with dislocation motion on the primary slip system only and also on all twelve slip systems have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing wave resonant specimen have also been calculated. The results of these calculatians are compared with earlier calculations on aluminum crystals and the relevance of these results to ultrasonic attenuation measurements is discussed. GREEN and inton' have recently outlined a procedure for determining the orientation factors for dislocation damping in single crystals. The stress field associated with a given mode of elastic wave propagation is resolved on the slip systems in which it is assumed the dislocations are vibrating due to this stress field. Since, at room temperature, slip has been observed on a limited number of systems in fcc and hcp metal crystals, it is assumed that these systems are the appropriate ones to use for the resolving process. This procedure has been applied to aluminum crystals by Hinton and hreen' and to zinc crystals by Henneke and Green.3 In the present paper the modes of elastic wave propagation have been calculated for copper crystals possessing orientations at 1-deg intervals throughout the standard stereographic triangle. The deviation of the energy flux vectors from the specimen axis have been calculated for each mode. The stress field associated with each mode has been resolved on the (111)(110) slip systems in order to determine the orientation factors for dislocation damping. MODES OF ELASTIC WAVE PROPAGATION For any direction in a linear homogeneous aniso-tropic material three elastic modes can be propagated. In general, each of these modes has both longitudinal and transverse particle displacements associated with it and thus are not "pure" modes. However, there is always one component which is greatest in either a longitudinal or transverse direction and hence the mode may be referred to as quasi-longitudinal or quasi-transverse, accordingly. For certain axes of high symmetry pure modes may be propagated. The phenomenon of refraction of the energy flux vector is also exhibited by elastic wave propagation in ani-

Jan 1, 1969

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed.

Jan 9, 1951

By Ford R. Bryan, Edward F. Runge

BECAUSE of the need for ductile heat resistant alloys of non-strategic composition, there has been metallurgical development of Fe-A1 alloys possessing improved ductility and hot strength, together with high oxidation resistance. Iron and alu- minum form solid solutions up to approximately 35 pct Al. Alloys in the 8 to 12 pct A1 range are characterized by excellent oxidation resistance, high electrical resistivity' and, when appropriately alloyed, have creep rupture strength equivalent to that of the austenitic stainless steels.' At higher aluminum levels, the magnetic properties are of considerable interest. Nachman and Buehler" have recently reported on the desirable magnetic characteristics of the 16 pct alloy.

Jan 1, 1957

Discussion of the paper of F. M. Simonds and E. Z. Burns, presented at the New York Meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 369 to 402. W. L. SAUNDERS, New York,. N. Y.:-Mr. Burns in his native Colorado modesty has said that he apologizes for things left out of this paper. I am much impressed by what he has put into the paper, as of all the papers that I have read on the subject, describing, as it does, a specific piece of work that has been accomplished, I do not recall one that gives so much information in such a practical way. Mr. Burns has also said that it is very hard to get men to put things down while the work is being driven. My experience is that it is very much harder to get the men in charge of work of this kind to bring them in in the form of a report before a body of engineers after the work is done. We have a great many cases where records are kept in much detail, but they are usually kept under cover, with the mistaken idea that the information gained is private information for the benefit of those who have done the work. Messrs. Simonds and Burns have opened up this case so that we can get the benefit of that experience which they have had, and so that we can learn something for the future. The description contained in this paper, as I have said, is a very practical one. You will notice in going through it. that the authors have given in detail a record of their work from the beginning to the end, and they even go so far as to publish an exact copy of the Rawley Mining Co.'s daily report. That daily report is something which those of us who are engaged in similar work might copy to great advantage, and having it before us we can check up our men while doing work and exact from them equal conditions, if it is possible to do so.

Jan 5, 1913