Search Documents

By U. N. Bhrany, J. H. Brown

The specifications of particle size and the size analyses of fine particulate materials are commonly presented without reference to the method of analysis. A review of the various sizing methods showed that not only numerous sources of error but also different definitions of size are inherent in the different methods of analysis. To demonstrate the magnitude of the differences, the size distribution of finely crushed quartz was determined by several methods and a critical comparison of the data was made. The experimental results show that appreciably different sizes may be indicated for one material depending on the method of analysis used. However, because the shape of the size-distribution curves determined by almost all methods was constant, a simple method of correlating the data can be adopted. Conversion factors, by which size measurements obtained by the various methods can be expressed in terms of screen sizes, are presented as one method of correlating the results. The size analysis and size specification for lump rock and particulate materials are commonly determined with sieves. With this technique, a readily reproducible measure of size can be obtained merely by duplicating the sieve and the method of sizing. For coarse materials, such as lumps of rock, this technique is simple and effective; and the effects of properties of the material such as shape can be readily understood. When very small particles are measured, however, problems arise. Small sieves are difficult to construct and maintain, and size separations become sensitive to the analytical procedure. For these difficult sieve sizes and for still smaller particles, other sizing techniques employing, for example, sedimentation, light extinction, and microscopy are available. Because these various techniques employ different size-dependent responses to establish size, it is appropriate to examine them and the results they yield to determine their relationships and their limitations. The 'size' of a lump of rock is not an absolute quantity, but rather a defined one. With sieves, for example, the size is defined by the screen aperture and no reference is made to the actual shape of the particle, yet only in the case of a regular body, such as a sphere, can the sieve size be related to the shape. With sieves only two dimensions of a particle can be suggested, for the sieve makes no allowance for the length of the particle passing through an aperture. Similarly, the size of a particle as measured by a microscopic technique need bear no relationship to the size as measured by sieves, although the two measurements may be related statistically. In fact, all size measurements are not only defined quantities, but the measurement actually used is an average that is controlled by the technique employed and, hopefully, reflects the property in question of the material of interest. Many papers have been presented that illustrate the accuracy of the various sizing methods, present the advantages of certain methods for certain applications, and describe the principles and technical backgrounds of the various methods. No attempt will be made in the present paper to review this work in detail. The purpose of the present paper is to examine the limitations of the various sizing methods, and to demonstrate experimentally the relationships between the sizes as determined by the various methods of analysis. It is hoped that by recognition of these limitations and relationships, errors in size specification and size interpretation will be avoided. REVIEW OF SIZING METHODS In specifying the size of a material, not only the data but also the method of measurement must be stated. For example, the size of the lump might be specified as its total volume, as its weight, as its maximum dimension, or as its minimum cross section; any one definition might be completely satisfactory for one problem, but not for another. In practice, size analyses follow four basic approaches and fortunately, the conditions that restrict each approach are known. These major methods include: 1) screen analysis, 2) direct measurement of particle dimensions, 3) determination of equivalent spherical size in response to fluid flow, and 4) specific surface determination. Each of these techniques has several variations and some new techniques are also available, but the limitations of the basic techniques are sufficient to permit at least a preliminary

Jan 1, 1962

Discussion of the paper of J. IV. GWINN, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 239 to 247. GIRARD B. ROSENBLATT, Salt Lake City, Utah (communication to the Secretary*).-The storage-battery locomotive certainly has its place in metal mining and I an) glad to note that it is now receiving the recognition that is its clue. It is, however, not a panacea for all conditions of mine haulage. There are places where it will not work to advantage and cannot compare with` the trolley-type locomotive in cost of operation or in cost of maintenance. On the one hand, there are places where it clearly outshines the trolley-type locomotive. Much depends on the headroom available in the drifts and on the condition of the roof. For short hauls with moderate-

Jan 5, 1915

By Robert C. Stephenson

In 1954, a year when general industrial production declined, it is significant that industrial mineral products continued in high demand. Phenomenal growth of the cement industry, increase in filler-fibre markets such as for asbestos and diatomite, expansion of the gypsum industry, and the increasing production of agricultural raw materials all illustrate the vitality of industrial minerals fields. Pioneer development of new industrial raw materials-wollastonite as a current example-requires keen foresight, hard work, and tremendous intestinal fortitude. The present-day requirements of industry for rigid quality control and uniformity of raw materials have resulted in highly specialized

Jan 3, 1955

By Robert T. Ault

The nature of fracture in unnotched tensile and notched tensile sheet and round specimens and V -notched and precracked Charpy-type sheet specimens of both wrought stress -relieved and re-crystallized molybdenum was investigated over the temperature range of -78° to 300°C. The sharp rise in fracture stress, for unnotched tensile samples, as the temperature is increased above the brittleness transition temperature (Tb), is found to be a result of an increase in flow stress due to plastic constraint and an increased strain rate which results from the onset of necking at Tb . Quasi-brittle fracture in notched tensile samples is found to occur when the tensile stress at the elastic-plastic interface, beneath the root of the notch, reaches a maximum critical value, which is independent of test temperature over the range from —78° to 25°C, but dependent on microstructure. In the temperature range between 150° and 300°C, unnotched tensile and notched tensile samples alike are found to fracture by a ductile fibrous tearing process which is discontinuous in nature, as a result of the competition between the processes of tearing, through continued plastic flow, and local work hardening. Results from the V-notched and fatigue-cracked Charpy-type impact tests demonstrate that crack initiation is the governing factor in the low-temperature (-78° to 25°C) fracture process for molybdenum. In recent years, there has been considerable interest, and a commensurate number of investigations, concerning the duc tile-to-brittle transition in refractory metals. There has not developed, however, a satisfactory explanation for the uniaxial tensile fracture-stress transition which accompanies the well-known ductility transition. This matter therefore warranted investigation. In a similar manner, the increased importance of notched tensile strength values in evaluating materials and in design criteria requires a better understanding of the factors which control the fracture behavior of notched tensile samples. In a previous investigation1 of the nature of initial yielding and fracture in notched sheet molybdenum at room temperature, it was suggested that plastic constraint was the controlling factor in governing the fracture behavior of notched samples. The final portion of this investigation was concerned with the fracture toughness of molybdenum. Of particular interest was the comparison of effective surface energies for fracture in V-notched samples with fatigue-cracked, Charpy-type samples in order to ascertain the relative importance of the initiation and propagation phases of the fracture process. MATERIALS AND TEST PROCEDURE Sheet tensile, notched tensile, and V-notched Charpy specimens were prepared from 50-mil, stress-relieved molybdenum sheet.* Half of these specimens were vacuum-annealed for 1 hr at 1200°C and 7.5 x l0-5 Torr and furnace-cooled to produce a relatively uniform grain size of 0.30 mm diameter. Round notched and unnotched tensile specimens were prepared from warm-rolled and swaged 5/8-in.-diam bar.* These specimens were vacuum-annealed for 1 hr at 1350°C and 5 x lom5 Torr and furnace-cooled to produce a grain diameter of 0.11 mm. Material analyses in ppm were: C N O H Sheet 290 10 4 1 Bar 50 30 30 2 The unnotched tensile sheet specimens had a 1/4-in. gage width and a 1-in. gage length. The unnotched tensile round specimens had a 9/32-in. gage diameter and a 1-1/4-in. gage length. The sheet and round notch tensile specimens are shown in Fig. 1. All of the notched tensile specimens tested were tandem-notched in order to study the location and mode of fracture initiation. The tandem-notched specimens were carefully machined so that the largest variation in notch depth on a single specimen was 0.001 in. Thus, when fracture occurs, the extent of plastic deformation that exists in the un-fractured notch section is that which exists just prior to fracture. All of the tandem-notched sheet specimens were electrolytic ally polished and chemically etched prior to testing. The V-notched Charpy-type specimens machined from the 50-mil sheet material had the standard dimensions of 2.125 in. long, 0.394 in. deep, and a 0.010-in. root radius. The unnotched tensile and notched tensile tests were conducted over the temperature range of -78° to 300°C, in a 10,000-lb Instron Universal Testing Machine, at a constant crosshead speed of 0.020 in. per min. The V-notched Charpy-type

Jan 1, 1964

As already announced, the Arizona Meeting of the Institute is to be held from the 18th to the "25th of September. There will be a special train from New York City to Arizona and return, to take members and guests of the Institute to the meeting., The Committee in charge consists of Walter Douglas, Chairman, Cleveland E. Dodge, John C. Greenway, Arthur S. Dwight and Julius Kruttschnitt, Jr., and while the plans of this Committee are not complete, it may he announced that 'the train will be run with the requisite number of Pullman, dining and baggage cars to accommodate those who desire to go, which will accompany the party during the entire week of the Arizona Meeting as per the following program, including, of course, the visit to the Grand Canyon. It is especially desirable that the Committee should know, at as early a date as possible, the number of those who desire to make the trip; and those who desire special accommodations such as drawing rooms, state rooms, etc., are especially requested to communicate as soon as possible with the Secretary of the Institute, stating the number in their party.

Jan 6, 1916

By Robert H. Richards

IT will hardly be worth while to spend time over the discovery of this mine, how lumps of galena, were picked up and brought to town, and how legends were told of an old mine from which Revolutionary bullets were made. This is an entirely new mine, with no evidences of former or ancient workings in its immediate vicinity to guide or attract the prospector. The first pit was opened in May, 1874. In August I made a visit to this pit, which was 6 feet wide in the northwest direction, 12 feet long north 80° east, and 6 feet deep. About 4 tons of a galena carrying gray copper, siderite, and quartz, had been taken fron this pit. The lumps were all of them evidently float specimens, and varied from 8 to 12 inches thick, and showed very distinct indica- * An abstract of this paper was kindly presented by Dr. T. Sterry Hunt at the February meeting of the Institute, but as it was not fully written out until the following December, it will describe the mine in a little more advanced stage than when the paper was originally presented.

Jan 1, 1875

By Perry Olcott .

THE Taka oil field is in the northern part of Titus and Franklin Counties, in north- eastern Texas. The small town of Talco, from which the field derives its name, is on the P. & Mt. P. R. R., about 15 mi. north of Mt. Pleasant, the county seat of Titus County. The oil field extends east and west from the town of Talco, the approximate center. In May, 1924, R. L. Cannon, while doing surface geology for the Humble. Oil & Refining Co., mapped the surface trace of this fault structure as evidenced by Upper Midway faulted down against Lower Midway. In the interval of sixteen years between the original surface work and the recent productive well completion, approximately eight wells were drilled into the Woodbine sand without success. The structure was well defined by those tests and all of the wells en-

Jan 1, 1936

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,' no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3'4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers' that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson's ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Henry M. Howe, W. P. Barba

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By W. P. Barba, Henry M. Howe

When this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. Doctor Howe, then chairman of the Engineering Division of the National Research Council, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority of the members of the committee. To that end, the Engineering Division appointed a committee, consisting of the gentlemen whose names follow, to mention on1y those who retained their connection with it. At this time there were serious difficulties in the manufacture, for the Government. of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted. Committee on Steel Ingots W. P. Barba, chairman, Ordnance Dept., U. S. A. (formerly Vice Pres. & Gen. Mgr., Midvale Steel Co., Philadelphia). George K. Burgess, Chief of Division of Metallurgy, U. S. Bureau of Standards, Washington, D. C. Henry M. Howe, Then Chairman Engineering Division, National Research Council.

Jan 1, 1922

By F. X. Meyer

THE United States Smelting Refining and Mining Company maintains an ore-purchasing department for procurement of custom tonnages of milling and smelting ores and concentrates for treatment at its Midvale plant. Arrangements with other companies provide for treatment of Company and custom zinc concentrates. Location of the Midvale plant in the heart of the Western mining country makes it possible to serve shippers from these nine producing states: Arizona, California, Colorado, Idaho, Montana, Nevada, Oregon, Utah, and Washington. Shipments from most of these states travel over main-line railroads, delivery being made at Midvale within a short time after billing of the shipment. Shipments varying in size from a few sacks to carloads can be handled at

Jan 1, 1948

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By S. Whinery

In these times of sharp rivalry, both as to price and quality, among the makers and venders of engineering explosives, it is often desirable to be able to determine the relative energy or value of the various explosives offered for sale, in order to purchase intelligently ; or, having contracted for a large amount of an explosive of a certain standard quality, to be able to ascertain if the manufacturer keeps his product up to the specified standard. The simple and inexpensive apparatus described below was devised by the writer while engaged on the improvement of the Tennessee River, at MuscleShoals, under the direction of' Major W. R. King, U. S. Engineers, in the summer of 1879. It answered the purpose so well that it is thought that a brief account of it may be of interest to other engineers. It consisted, essentially, of an old blacksmith's anvil and a common striking hammer, such as is used for driving rock-drills. The anvil was placed face downward on solid, level ground. In what was then the top of it, a vertical hole, one and one-fourth inch in diameter and about one arid three-fourths inch deep, was made with a ratchetdrill. The surface of the anvil immediately around the drill-hole was made as true and smooth as possible with a file. Next, a new striking-hammer, weighing nine pounds, with a turned and true face, was selected ; and a handle, eleven feet long and about one and a half inches in diameter, was fitted into it so that it

Jan 1, 1886

By J. W. Harshbarger, E. L. Montgomery

The region of metallic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 6 km (19,700 ft). Because surface water supplies are meager, new mines require unexploited sources of water. Prolific ground water aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate ground water quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum capacities of more than 170 L/sec (2700 gpm) for individual production water wells. Results of investigations conducted by the authors demonstrate that ground water reservoirs in the Andean Highlands comprise a source of large quantities of water for the mineral industry.

Jan 1, 1986

By T. Egleston

THE works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882

By T. Egleston

The works of the Ore Knob Copper Company are situated in the county of Ashe in the northwestern part of the State of North Carolina, about ten miles from the Virginia line, at an elevation of 4600 feet above the sea. The nearest railroad station is at Marion, Smythe County, Virginia, about forty-five miles distant. The roads from the railroad to the works have been constructed by the company for the transportation of their material, and are very hilly, and in certain seasons of the year in bad repair. Transportation is therefore always limited and never easy, although it is done by contract at a very low price. The main difficulty with the transportation is not so much its cost as the fact that it puts a limit to the production of the works. These unfavorable conditions make it necessary for the owners of the mine to smelt their ores and to send to market nothing except the metal, which alone will bear the cost of transportation. The mine was opened previous to 1860, but has only been worked systematically during the last five or six years. The vein is a fissure vein from ten to twenty feet in thickness in the gneiss of the

Jan 1, 1882