Search Documents

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

This paper reviews the history of refractory materials, highlights the development of refractory technology over the years, draws attention to the technology behind these materials, and comments on future developments in this field. By walking the path with refractory materials, from their initial uses in BC times, to the composite materials that are used nowadays, and the nanotechnology developments that are currently taking place in this field, the reader will come to agree that refractory materials are indeed very ?cool?! Keywords: refractory materials; bricks; monolithic materials.

Jan 1, 2008

By E. C. Lane

[This is the tenth in a series of retorts on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee e end the Bureau of Mines of the United States Department of the Interior. The first report rave data on motor gasolines sold during .e winter of 1935-36.3/ The present report presents analytical data for 1,732 samples, representing the products of approximately 50 companies, which, as in previous surveys, include both lame and stall suppliers. In addition, the Pacific coast is represented by data that were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. he number of samples, items, and brands comprising each groan), exclusive of those of the Pacific coast, are as follows: Regular price, 934 samples, 230 items, and 50 brands; premium price, 465 saris samples, 184 items, 40 brands; third-grade gasolines, 360 samples, 177 items, and of these terms as used in the surveys are follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.]

Jan 1, 1941

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

By Antonio Raschillà

On the 2nd of June 2007 SELI S.p.A. started the excavation of Beles Tailrace Tunnel (Ethiopia). The new 8,07 m diameter DS Universal TBM utilized for the tunnel excavation was manufactured by SELI S.p.A. and allowed the installation of 30 cm thick concrete lining, contemporaneously with the excavation of 7,200 m of tunnel. The greatest part of the tunnel alignment was excavated in hard and sound basal-tic rocks. The paper describes the main steps of the tunnelling operations which led to a remarkably rapid excavation, with a peak production of 36 m / day and a final break-through achieved 46 days ahead of the contractual deadline. Furthermore the paper describes the work and logistic organization that was set up to efficiently perform the mechanized excavation in the very remote area of the project.

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

Past arguments advocating reverse circulation sampling against blasthole sampling are reviewed to present the debate under a different light. The advantages and disadvantages of each drilling method are compared, and the choice is presented as an informed trade-off between them.

Mar 1, 2010

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By Matters, R T, Coldham, Slee, J C, R J, Wallman

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs J C Moulden, Howchin, Twelvetrees, and the West Australian Geological Surveyfor various information; to Messrs J G Dreyer, S Pope, T Read, P Moncrieff, R Williams, and W J Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of Melbourne University, gave much valued assistance in petrology, and Mr Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-fust for silver, then for silver and lead, and at present for lead, silver, and zinc...

Jan 1, 1910

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By I M. Platten, C J. S Sangster, Y Xie

The Cononish gold-silver deposit is a steep, relatively narrow quartz-vein system, with a current total mineral resource of 154 000 oz Au and 589 000 oz Ag. The northeast-southwest trending system was emplaced into late Proterozoic metasediments, and postdates metamorphism and associated Caledonian Orogenic foliations. Assay and mineralogical data show that gold and silver is spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur in small amounts. Gold occurs as electrum, with minor native gold, and silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally less than 100 microns in size. The main ore shoots plunge 45¦ south-west, have a 40 m to 80 m intersection with the existing underground development and extend between 40 m and 260 m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two, and rarely three, of the domains are present at an individual site in the vein. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Geological mapping along a 1.2 km exploration adit has provided critical æconditioningÆ data to support resource evaluation based on development and relatively wide spaced drilling. In addition, it has provided an indication of potential challenges that could be encountered during production.

Jan 1, 2009