Search Documents

By Stanley G. Hutton, Robert Brubaker

"It has long been recognized that mining workers subjected to high levels of hand-transmitted vibration may suffer from vibration-related complaints. Prolonged exposure to whole-body vibration may also result in adverse effects. In this study, the effects of vibration on mining workers are examined. Previous work documenting the occurrence of vibration-related disease is reviewed. From this work, it is apparent that operators of hand-held pneumatic rock drills are exposed to a significant risk of developing vibration disease. Vibration levels recorded on the rock drills now in use are presented and shown to exceed levels recommended by a proposed ISO standard.IntroductionThe possible harmful effects of exposure to excessive vibration levels have long been recognized, particularly among operators of hand-held tools. Numerous cases have been reported of a vasospastic disorder commonly known as vibration white finger disease (VWFD), which was a term coined by the Industrial Injuries Advisory Council in Scotland in 1970(1 ), Those suffering with the disorder have frequent vasospastic attacks in which the fingers, hand and, in advanced cases, the lower arm turn white and numb, usually after a cold stimulus. Advanced stages of VWFD have been reported in which the skin becomes ulcerated and gangrenousm. The incidence of the disease has been particularly serious in the forest industry due to the extensive use of chain saws. However, in recent years, the introduction of antivibration saws has resulted in a significant reduction in the occurrence of the disease.In a recent report for the Canadian Department of Supply and Services - Energy, Mines and Resources, Hutton & Brubaker considered the effects of vibration on workers in the mining industry. In this report, the physiological and medical effects of vibration were considered, relevant vibration standards were discussed, previous vibration measurements were documented and field measurements carried out. In the present paper, the results recorded in this study will be summarized, together with results that have been previously published relating to vibration levels existing in the mining industry."

Jan 1, 1982

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

A study was made of zircon powders bonded with phosphoric acid or aluminium orthophosphate. The influence of strength of solution of the phosphatic binders on the modulus of rupture over a temperature range was investigated. Physical properties of three grades of zircon powder bonded with phosphatic binders were studied at various temperatures. Examination of x-ray diffraction data indicated that phosphates ofzirconia are preferentially formed to phosphates of silica. However, zircon in the presence of excess phosphoric acid also forms phosphates of silica upon heating.Resistance to attack by slags from blast and open hearth furnaces was determined on phosphate-bonded zircon mortars in a cup test with industrially made ladle bricks. Zircon powders bonded with phosphates proved to have high P.C.E. values. The first satisfactory results of a plant trial with phosphate-bonded zircon mortar, used in a steel ladle, are now being assessed in larger scale industrial tests prior to accepting the mortar as a steel plant refractory.

Jan 1, 1972

By M. Beth McClenaghan

This paper summarizes diamond exploration techniques used in glaciated terrain, focusing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments are essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 to 0.5 mm) fraction of heavy mineral concentrates prepared from glacial sediment samples is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and REE, the relative importance of which will depend on kimberlite composition as well as that of the surrounding bedrock.

May 1, 2002

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By J. W. van der Merwe, A. S. Bolokang, M. J. Phasha, V. J. Matjeke, C. Moopanar

"Excessive wear rates on railway wheels can result in rolling-stock derailments. If wear is detected early the possible derailments can be prevented by prematurely replacing wheelsets, although the inventory cost and maintenance downtime remain a challenge. In the current study, wheels were introduced and monitored in-service for two years to investigate the cause of excessive wear rates. The wear rates and stresses were calculated for the wheels suitable for a maximum load of 26 t per axle. Microstructural and mechanical properties were analysed. As expected, the general microstructure of all the wheels tested was pearlitic. Although all the wheels complied with the tensile strength requirements, stress calculations confirmed material distortion on excessively worn wheels whereas trial wheels revealed yield strength exceeding the yield criterion. High wear rates observed on the wheels were a result of low yield strength relative to the load per axle. The typical wear mechanism found was due to a combination of rolling contact fatigue and abrasive brake wear. Despite compliance of the wheels with existing requirements regarding material and mechanical properties (hardness, ultimate tensile strength), it is recommended that the yield strength must also be taken into consideration as a critical parameter.IntroductionRailway wheels are used to support the wagon mass and guide the wagon along the tracks (Park, 1974). The wheels and rails must be able to tolerate the applied tangential forces in order to effect wagon dynamic performance and reduce material deformation (Ghidini et al., 1994; RSE_TE_SPC_0045, 2011; AAR M107/M 208 Specification, 2011. Over the past ten years, the South African coal wagon maintenance depot has experienced excessive hollow wheel wear rates on the heavy haul line wheels. The maximum load of Jumbo wagons on the coal line is 104 t, or 26 t per axle. Although the maintenance intervention cycle for wheelsets was two years, between February 2011 and August 2012 some wheels experienced excessive hollow wear. Hollow wear is regarded as wear exceeding 2 mm on the central portion of the wheel tread (RSE_TE_SPC_0045, 2011). This happened despite the fact that these wheels were manufactured and certified according to the requirements of AAR M107/208 standard for carbon steel wheels (AAR M107/M 208 Specification,. 2011) and the local wheel RS/ME/SP 021 standard specification (RS / ME / SP / 021 REV 5 (2013). The AAR standard only specifies a minimum hardness as a required mechanical property and the local standard specifies hardness and minimum tensile strength only. In general, an increase in hardness will improve the rolling/sliding wear resistance of steel. This relationship of hardness and wear resistance was found to be true only in a situation where solid and similar alloys are in contact (Singh, Khatirkar and Sapate, 2015). The sliding wear resistance of a material is usually estimated using Archard’s equation (Liu and Li, 2001)."

Jan 1, 2016

By Hugo Medina M.

Dado que la producción de carbón en el Perú es menor frente a la demanda de petróleo, es necesario plantear una planificación de su estudio y sus posibilidades de desarrollo minero. En este sentido, el presente texto revisa las áreas prospectivas de carbón, reservas y su potencial como mineral con la finalidad de incentivar la reconversión industrial y las inversiones del mineral. Asimismo, señala los factores que afectan el desarrollo minero como el potencial carbonífero no tangibilizado a reservas, superposición, acaparamiento, prioritización y áreas reducidas; asistencia tecnológica y técnica y financiamiento. Finalmente, entre las alternativas de solución está el plan exploratorio nacional, operación minera, apoyo técnico, política de precios, madera, costo del transporte, capacitación e investigación, centrales hidrometalúrgicos, plantas de lavado de carbón y una ley de promoción carbonífera.

Aug 26, 1988

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By J. H. East

THE RIFLE, COLO., oil-shale project of the Bureau of Mines was a facet of the re-search and development activities conducted under the Synthetic Liquid Fuels Act (Public Law 78-290) of April 5, 1944. The principal objectives were to devise efficient methods to mine and retort oil shale and to refine shale oil into usable products, at a total cost low enough that shale oil could supplement the domestic supply of petroleum at competitive prices. The Rifle project included three major divisions: (1) Mining, (2) retorting, and (3) refining. The major functions of the mining program were to supply oil shale to the retorts, to devise mining procedures, and to develop an under-ground-mining method by which oil shale could be produced safely at an unusually low cost per ton. The selected mining procedures and direct mining costs were demonstrated by sustained test runs.

Jan 1, 1964

By Jacques B. Wertz

Recurring movements remotely connected with the Murray fracture zone and the San Andreas fault complex, together with the slow northwestward drift affecting the Baja California peninsula, could progressively have accentuated the tensional situation already connected with the anticlinorium in southern Arizona. From the fragmentary data gathered on the Texas lineament, it appears that a very mild curvature, concave to the northeast, may be present along this belt throughout Arizona. Those localities where the successive changes in direc¬tion of the strands of the lineament belt seem to occur do generally coincide with intersections of both north-northwestern and northeastern breaks. It is along the outward, southern fringe of the belt (at such structural centers like Bisbee, Baboquivari, Ajo) that the greatest impact of regional movements could be expected to have occurred through tangential-torsional stresses. Although it si accepted that the north-northwestern and more particu¬larly the northeastern fractures in Southeast Arizona are propitious to or partially responsible for mineralization, it seems undeniable that the Texas lineament belt must have greatly increased the potentialities for ore throughout the Arizona copper province. While intrusive bodies occur near major intersections, with the Texas lineament belt as a common denominator, it seems, the ore deposits are to be found close to one of the intrusive stocks, varying in distance from contiguity (Bisbee) to one or two miles away (Silver Bell orebodies).

Jan 1, 1970

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By I. R. Kramer

I. R. Kramer (Martin Co.)—In a recent paper Nakada and Chalmers24 reported some observations of effects of surface conditions on the stress-strain curves of aluminum and gold single crystals. It is of interest to compare these observations with the results published previously in this journal and to comment on their general conclusions. In brief, Nakada and Chalmers concluded that the removal of the surface layer of a prestrained specimen lowered the stress-strain curve for aluminum but not that for gold. Further, they concluded that the surface work hardening of aluminum is confined to a depth not more than l0-3 cm. In our results25 published previously, it was pointed out that when prestrained specimens of aluminum and gold were polished to reduce the thickness upon reloading the initial flow stress decreased markedly. Further if a sufficient amount of metal was removed, the yield point failed to appear. With continued application of the load the stress-strain curve became coincident with that of the virgin crystal. We have found this behavior in some 100 determinations to hold consistently for gold, aluminum, and copper in both single and poly-crystalline specimens. The amount of strain required before the curves coincided depends upon the amount of metal removed but it is usually less than 0.01. This type of behavior is the same as that reported for metarecovery by other investigators.29 For aluminum specimens which have been prestrained and then heated to temperatures above 50°C we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen. With respect to Ref. 24 the curves for aluminum are always below that of the virgin curves, while those for gold become coincident. This observation indicates at least for aluminum that the specimens must have been heated to a temperature high enough to cause recovery by an alteration of the internal dislocations. In addition, a recovery would be expected because of the removal of the surface work-hardened layer. Nakada27 had reported that, with his particular apparatus in which a perchloric acid polishing solution was used, the temperature of the specimen increased 65°C. The curves presented in Ref. 24 for gold do not permit one to detect the initial flow stress upon reloading after the surface-removal treatment. In fact, contrary to the method used by Nakada and Chalmers, the change in the stress-strain curve produced by a surface-removal treatment cannot be described in terms of a decrease in stress at strains much higher than that at the initial flow stress because of the coincidence of the curves at the higher strain values. With regard to the depth of the work-hardened surface layer, our data show for aluminum single crystals (7.5 by 0.3 by 0.3 cm) that the initial flow stress remained constant after 12 x 10-3 cm had been removed from the thickness. This depth was independent of the prior strain. For gold crystals this depth is somewhere between 10 x 10-3 and 20 x 10-3 cm. Y. Nakada (author&apos;s reply)— Kramer states,28 "for aluminum specimens which have been prestrained and then heated to temperatures above 50°C, we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen." However, Cherian et a1.26 discovered that aluminum polycrystals annealed at 32" and 100°C showed the metarecovery behavior. They showed that the orthorecovery behavior did not appear until the crystals were annealed at 150°C. Kramer suggests28 that the drop in the flow stress of aluminum crystals after the surface removal by electropolishing24 may be due to the recovery caused by the temperature rise which may occur during the electropolishing.27 However, as indirectly stated in Ref. 24, the current density used in these electro -polishing experiments was 0.15 amp per sq cm. According to ref. 27, this current density should cause a temperature rise of only 40°C. This may cause the metarecovery but not the orthorecovery. Furthermore, as stated explicitly in Ref. 24, the surface removal was accomplished by chemical etching as well as by electropolishing. The results were the same for both electropolishing and etching. During the etching, the specimen temperature did not rise above 35°C. Some aluminum crystals were placed in water at 35° C for 30 min. These crystals did not show the decrease in flow stress. Therefore, it is quite clear that the flow-stress drop after the surface removal is not caused by a high-temperature recovery. However, as Kramer points out,28 it is quite possible that the internal dislocation structure may have been altered because of the removal of the highly work-hardened surface layer. However, how much this rearrangement contributes toward the flow-stress decrease is not known at present.

Jan 1, 1965

By J. T. Ryan

FIGURES for the first 11 months of 1935 indicate that the total coal production of the United States for 1935 will be approximately 416,000,000 tons, or almost identical with the production figures for 1934. Bituminous production will show a gain of about six million tons, and anthracite production a loss of about the same tonnage, compared with the previous year. This does not take into account so-called "bootleg" anthracite coal amounting to approximately 5,000,000 tons. Twenty-nine years ago, in 1906, the production of coal was almost identical with this year&apos;s production. At that time, 626,000 men were employed in producing this tonnage, which took a toll of 2138 lives from accidents. In 1935, approximately 540,000 men were required to produce the same tonnage with an estimated loss of 1155 lives. This shows definite safety advancement in the industry, but even so accidents are still costing an average of 3c. a ton more than they should.

Jan 1, 1936

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By André Vien, Pedro Gonzalez, Julio Palomino, Rob Perry

"In many mineral processing plants ore is reclaimed from a stockpile using multiple feeders. The discharge from these feeders is combined onto a single conveyor from which total tonnage is measured. Typically, operators set feeder output ratios to adjust the proportion of total tonnage drawn from each feeder. From a process control perspective, this system is not easy to control because the response time of each feeder depends on the distance from the feeder to the weightometer. This paper proposes a simple and elegant process control strategy to manage feeder ratio changes and the associated long and varying process dead-times. Changes in feeder speed are delayed and filtered to compensate for transport delays between feeders. The strategy was evaluated by simulation and installed on a mill feed system.ResumenEn numerosas plantas procesadoras de minerales, el mineral es extraido desde una pila de almacenamiento usando varios alimentadores. La descarga de estos alimentadores es recibida por zinica correa transportadora, en la cual se mide el tonelaje total. Comzinmente, los operadores colocan un valor determinado en cada controlador de razdn para ajustar la proporcidn del tonelaje total extraido por los alimentadores. Desde el punto de vista del control automatic0 de procesos, este sistema es dijkil de manejar debido a que el tiempo de respuesta de cada alimentador depende de la distancia de este respecto a la ubicacidn del pesdmetro. Este trabajo, propone una estrategia de control, simple y elegante, para compensar los cambios de razdn a cada alimentador y los tiempos muertos del proceso largos y variables. Los cambios en la velocidad de los alimentadores son retardadas y filtradas para compensar los retardos del transporte entre alimentadores. La estrategia fue evaluada por simulacidn, instalada y probada en un sistema de alimentacidn a molino."

Jan 1, 2000

By Alan M. Jessop

This paper discusses the distribution of frozen ground in the zone of discontinuous permafrost in relation to the pattern of surface temperature. The importance of understanding permafrost in relation to surface construction and open-pit mining operations is stressed.

Jan 1, 1972

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012