Search Documents

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By M. I. Kalashnikova

In hydrometallurgical technological flowsheets several methods of target components removal from solution are used. One of these methods is non-ferrous metals removal in the form of rich selective or collective concentrates. In the present work pyrometallugical mattes, thiosulphate containing solutions and pulps, iron powder with elemental sulphur and calcium sulphate were used as the precipitator. It was shown that depending on precipitator compound and process parameters non-ferrous metals precipitate from solution in the different forms with varying content of components including Ni3S2, NiS, Ni3S4, NiS2, (Ni,Co)S2, CuS; Cu1,765S; Cu1,97S.

Jan 1, 2006

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Vladimir Panjkovic, Ostrovski. Oieg, Campbell Cripps Clark, John Truelove

"Effects of properties of raw materials and blast on the performance of an iron bath reactor have been examined by a mathematical model. The model consists of three modules: 1) chemical reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, post-combustion ratio and heat-transfer efficiency, temperature and composition of the off-gas, and slag and metal chemistry.IntroductionOne of the anticipated advantages of smelting reduction over conventional ironmaking is the use of lower-grade raw materials. In this work, the effect of-properties of raw materials on the performance of an iron-bath reactor is examined with a numerical model. The model is also used to assess the effect of properties of the blast (flowrate, temperature and oxygen enrichment) and ejected droplets (generation rate, size and ratio of total weights of slag and iron droplets) on the key parameters of the process. In the process coal, oxygen, ore (which may be partly prereduced) and fluxes for specified slag composition are charged to the bath. Slag and iron droplets are ejected from the bath into the gas phase, where they are heated before returning to the bath. Iron droplets undergo decarburisation and reoxidation with CO2 and H2O. Dust is also generated from the bath, and oxygen or preheated air for post combustion is injected from the top of the vessel.The model consists of three modules: 1) reactions in the gas phase and heat transfer from gas to droplets ejected from the bath; 2) heat losses from the vessel and radiative heat transfer from the freeboard to the bath; and 3) heat and mass balances for the bath. The structure of the model and the data exchange between the modules are shown in Fig. 1. The following parameters of the process are calculated: coal, ore, flux and oxygen consumption, postcombustion ratio (PCR), heat transfer efficiency (HTE), off-gas temperature and composition, slag and metal chemistry, and rates of decarburisation and reoxidation of the iron droplets."

Jan 1, 1996

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By F. Elgersma

Hydrometallurgical zinc winning processes ?are frequently based on iron containing concentrates which yield a goethite, jarosite or hematite residue. Jarosite or goethite are mostly stored in waste ponds which ,are lined with foil. Water percolating through the pond is withdrawn from the deposit ,and decontaminated before discharge. Despite these measures, more and more pressure is put upon zinc companies to treat their (historical) residues and to produce environmentally acceptable residues. The criterion which determines this acceptability is the potentiality of leaching out hazardous elements by natural processes. This paper provides the comparison of five different process designs for integrated jarosite treatment in a hydrometallurgical zinc winning plant leading to environmentally acceptable residues. The processes are esigned for producing 200 ktons/yr zinc and for treating 80 ktonslyr historical jarosite. Mass and energy balances are used to determme parameters such as: the energy use per ton waste treated and the amount and composition of final residues. The conclusion of the work is that. pyrometallurgical jarosite treatment integrated in hydrometallurgical zinc winning is preferable to hydrometallurgical jarosite treatment. Integrated pyrometallurgical processes lead to a ?smaller quantity of remaining hazardous residues and require less energy.

Jan 1, 1992

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process. The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Adrian C. Deneys, David G. C. Robertson

"Fluid flow phenomena on the surface of a molten slag have been documented using video photography in a laboratory scale D.C. arc furnace. The flow on the surface of the slag appeared to be electromagnetically influenced. This was confirmed by varying the position of the anode, which changed the direction of flow on the surface of the slag. Temperature measurements in the bath also confirmed the change in the directional nature of the fluid flow induced by the arc.During some periods, solids were fed into the arc attachment zone (AAZ) down the center of the hollow graphite electrode. Significant movement of the arc around the basal annular surface of the hollow electrode takes place. The point of attachment of an arc on a hollow electrode was more variable than an arc attached to a solid graphite electrode. Video images showed that the solids were rapidly incorporated into the bulk of the slag. Temperature measurements confirmed the existence of a superheated slag layer at the slag-gas interface, which allowed the solids to be rapidly incorporated into the melt.This work has been conducted to study fluid flow, temperatures, and solid behavior during feeding, in the arc attachment zone of a D.C. arc furnace. The work also has relevance to optimizing furnace design for pyrometallurgical slag cleaning processes."

Jan 1, 1999

By Evgenii Pavlov, Ivan Tronin, Viktor Timofeev, Vladimir Kislov, Sergei Bogovalov

"Modeling of the magnetohydrodynamical (MHD) and thermodynamical processes during the industrial scale Direct Chill (DC) casting of aluminum slabs is performed using a combination of ANSYS/CFX and ANSYS/EMAG software. The electromagnetic field is modeled through ANSYS/EMAG, while hydrodynamic and thermodynamic processes are modeled through ANSYS/CFX. Both packages were modified in order to calculate MHD flows in the liquid pool that forms during aluminum DC casting, and they were unified into a software combination that provides simultaneous simulation of all the above processes. The simulation shows that the electromagnetic stirring of the molten aluminum changes the shape of the solidification front (solid-liquid interface) very dramatically, namely it becomes significantly flatter. This effect should improve the internal structure of aluminum DC slabs and allows us to increase the casting velocity.IntroductionProduction of Aluminum alloys with high mechanical properties and structural uniformity is one of the main goals of industry. The preferred production method of aluminum alloys in most modern plants is Direct Chill (hereafter DC) casting because it offers high productivity and commercial success. One important limitation of this technology is the development of centerline shrinkage in slabs larger than about 1 meter. The improvement of the internal structure of long DC cast slabs can be achieved by electromagnetic stirring (hereafter ES) of the liquid metal above the solidification front. This intensifies heat transport in the zone close to the solidification front and suppresses shrinkage formation."

Jan 1, 2013

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

By P. S. Dunn, A. D. Rollett, H. D. Lewis

"The results of preliminary work on the modeling and measurement of the heat transfer coefficients of metal/mold interfaces is reported. The system investigated is the casting of uranium in graphite molds. The motivation for the work is primarily to improve the accuracy of process modeling of prototype mold designs at the Los Alamos Foundry. The evolution in design of a suitable mold for unidirectional solidification is described, illustrating the value of simulating mold designs prior to use. Experiment indicated a heat transfer coefficient of 2 kW/m /K both with and without superheat. It was possible to distinguish between solidification due to the mold and that due to radiative heat loss. This permitted an experimental estimate of the emissivity, ~ = 0.2, of the solidified metal.IntroductionA feature that distinguishes casting processes from welding processes is the presence of an interface with a low heat transfer coefficient between the mold and the casting. Especially when chill casting, the interface delays the start of solidification and increases freezing times significantly. By comparison welds can be assumed to have a very high heat transfer coefficient. The heat transfer coefficient controls such phenomena as folds and laps on the surface of castings which can be crucial to the acceptability of a casting. The time delay for the start of solidification influences the occurrence of cold shut defects. The standard mold material for uranium casting is high quality graphite which is an excellent refractory when used in vacuum and coated with a refractory wash. Graphite is an effective chill material and has a thermal diffusivity approximately twice that of uranium. Experience has shown that practicable superheat without mold pre-heat is not sufficient for avoiding cold shut defects when casting in graphite molds.TheoryIt is possible to calculate the position of the freeze front s, as a function of time, t, the superheat and interface heat transfer coefficient, h, [1]. However, the value of h cannot be obtained explicitly. The Virtual Adjunct Method (VAM) [2] offers a method for extending the standard equation for an insulating mold where s is proportional to the square root of time. By considering the effect of the interface to be equivalent to finite thicknesses of mold and metal, the following quadratic equation is obtained,"

Jan 1, 1986

By A. Dadgar

The adsorption kinetics of AuBr4 on Dowex ® -21K ion-exchange resin were studied and found to be independent of the initial gold, bromine, and base metals concentrations. A commercially-available undivided hypochlorite generating cell was used to generate bromine from simulated mixed halide (Br-/CI-) solutions. Electrolyses were performed with solutions containing very low Br' ion concentrations. The current efficiencies were 80-90%, and Br- ion utilization was maximized. A detailed economic assessment was made considering the capital and the operating costs for a 1000 mtpd gold ore processing plant. The toxicity and discharge levels of bromide, bromine, and cyanide were compared from a detailed analysis of the published literature data. Comparing bromine vapor with hydrogen cyanide gas for a given length of exposure, the lethal concentration of bromine is about 3 times less than hydrogen cyanide. The toxicity of sodium bromide is similar to that of sodium chloride. Acute poisoning to bromides and chlorides is rare because of their low toxicities. The allowed discharge levels of Br-, Br2, and CN- in fresh water are 250, 0.1, and 0.005 mg dm-3, respectively.

Jan 1, 1992

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Huayi Yin, Wang. Dihua, Wei Xiao, Xuhui Mao, Diyong Tang

"The world production of crude steel reached 1.55 billion tons in 2012,which generated ~2.5 billion tons of CO2. Electrochemical metallurgy especially through high temperature molten salt electrolysis with renewable electricity stands for a great opportunity for producing “green” metals. In recent years, electrolytic production of iron without emission of CO2 in different molten salt systems has been reported. A cost-affordable inert anode is the key to produce acceptable eco-friendly iron by the novel molten salt electrolysis processes. Based on the authors’ research, this paper will discuss iron production by molten salt electrolysis using a nickel alloy inert anode. On the other hand, the paper also covers a novel molten salt CO2 capture and electrochemical transformation (MSCC-ET) process, in which CO2 is effectively converted to value-added carbon and oxygen in a molten bath using a cost-affordable nonconsumable SnO2 anode.1. IntroductionEnergy and materials are cornerstones to support the development of human society. The traditional primary metal production, especially iron and steel, and electricity production are mainly based on the reactions between carbon (coal) and oxygen (represented by equations (1) and (2) respectively), which produce huge amount of CO2.MxOy + 0.5y C = x M + 0.5y CO2 (g) + Q1 ( 1 )C + O2 (g) = CO2 (g) + Q2 ( 2 )In 2012, the world production of crude steel reached 1.55 billion tons, of which 46.3 %, ~0.7165 billion tons were produced in China. Based on the average level of 1.7t CO2 emission per ton steel, more than 1 billion tons of CO2 generated from steel industry in China in the year. Besides the iron and steel industry, thermal power plant leads the CO2 emission in both USA and China. The total consumed electricity in China increased to 4959 billion kWh in 2012, ~70% of it was from coal fired power plant. The average CO2 emission for electricity production in the typical thermal power plant in China is around 0.78 kg kWh-1. It accounts for ~ 3.868 billion tons of CO2 emission from thermal power plant in 2012 in China."

Jan 1, 2014

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006