Search Documents

By T. H. Courtney, B. R. Murphy

"Nominal room temperature mechanical alloying (MA) has been used to synthesize the high melting temperature NbC and Cu-NbC composites. Elemental powders of Cu and Nb were alloyed in the presence of either graphite or hexane to form nanocrystalline NbC or a Cu-NbC composite. Through control of hot-isostatic-pressing (H/Ping) parameters, we have been able to minimize microstructural coarsening during densijication, and have processed fully dense bulk compacts of both single phase NbC and two-phase Cu-NbC while maintaining a nanocrystalline or near-nanocrystalline structure. These materials generally exhibit high strength and low fracture toughness. However, mechanical properties vary significantly depending upon the Cu content and the method of NbC synthesis (graphite or hexane).INTRODUCTIONMechanical alloying (MA) has been recently used to synthesize a variety of inorganic solids; sulfides (1-2), nitrides (3), borides (4), and carbides (3, 5-8). One advantage of this processing route is that synthesis of fairly high melting temperature materials takes place at what is nominally room temperature. Another advantage is that the structures generated are often nanocrystalline in scale, with attendant interesting properties. The consolidation of these fine structures into near fully dense or fully dense materials while limiting microstructural coarsening is a challenge that has just recently seen limited success (5, 9). We report here on some recent studies of ours dealing with crystallite size and structural analysis of NbC and CuNbC composites consolidated to full density from mechanically alloyed powders. Bulk mechanical properties and their dependence on milling parameters are also presented."

Jan 1, 1994

By Leonid N. Shekhter, Corby G. Anderson, Esra Cankaya-Yalcin, Daniel G. Gribbin, Joseph D. Lessard, Larry F. McHugh

"A new process for smelting copper, Looping Sulfide Oxidation™ (LSO™) significantly and positively alters the smelting energy balance. This process uses copper oxide in conjunction with air for the desulfurization of copper and chalcopyrite concentrates. Copper oxide is regenerated in a flash type furnace and then ""looped"" back for the oxidation of the copper concentrate. Heat and material balances show that the Looping Sulfide Oxidation™ process requires significantly lower net energy than conventional technology. This process produces anode copper and higher S02 content off-gases for efficient formation of sulfuric acid. Additionally, the process yields slags with lower copper solubility as compared to the conventional technology.IntroductionBased on the positive results from LSO™ investigations [1], further lab investigations into co=on sulfides and metal oxides were performed. It was discovered that chalcopyrite (CuFeS2) is oxidized with copper (II) oxide. In this reaction over 98.5% of sulfur was removed as S02, while a significantly improved energy balance was observed. This paper intends to analyze both the conventional flash smelting process and the newly developed Looping Sulfide Oxidation™ process, comparing heat and material balance results. LSO™ yields improvements to the energy footprint for copper, opening the door to new copper processing opportunities."

Jan 1, 2013

By Xirneng Zhu

The electrochemical behavior of Pittsburgh and Illinois coal pyrite in basic and neutral borate/sulfate solutions was investigated. In the transpassive region, aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The formation of sulfur and polysulfides was identified by in-situ Raman spectroscopy. The growth kinetics of the reaction product film, resulting from transpassive oxidation of coal pyrites, were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The reaction rate was well correlated by a paralinear rate equation. The effects of electrode rotation speed, solution pH and temperature were examined. The kinetics were compared to those for mineral pyrite.

Jan 1, 1994

By Shengli Wu, Jinming Zhu, Wei Huang, Xinliang Liu

The sinter of high basicity would interact with lump ores or acid pellets in the cohesive zone of blast furnace due to the difference of chemical composition and micro structures. The results of this work showed that the softening-melting properties of lump ores and acid pellet would be obviously improved by the high temperature interaction. However, the high temperature interaction index (INI) would be influenced by many factors, such as chemical composition, porosity, interaction interface and so on. The INI between sinter and porous limonite lump ore (L-2) was much higher than that of dense hematite lump ore (L-1) and acid pellet (P-1). In addition, though the softening and melting properties of L-2 were poorest in respective iron ores, the softening and melting properties of integrated burden B (consist of sinter and L-2) were not worse than other integrated burdens due to the strong high temperature interaction.

Jan 1, 2015

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. In 1996, however, it successfully shifted to a single furnace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By M. J. Adam

As part of its research programs, the Bureau of Mines is investigating the partitioning of complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Partitioning in this manner can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving the sulfidation partitioning of the mineral pentlandite, which is an important source of Ni in primary production. For the laboratory studies, the pentlandite was synthesized in nominally equiatomic proportions of Ni and Fe. Elemental Ni, Fe, and S powders were blended, compacted, and sealed under reduced He pressure in vitreous silica tubes. The tubes were heated under controlled conditions at SOD? C for 24 h. The product was verified by X-ray diffraction and chemical analysis to consist essentially of (Ni,Fe)9S8. Small samples of the (Ni,Fe) S were encapsulated with sulfur in silica tubes at reduced He pressures and heated for 1 to 24 h at specific temperatures between 400? and 600? C, both below and above the boiling point of sulfur (_445° Cl. Reaction rate increased with temperature. Within this temperature range, partitioning to individual Ni and Fe disu1fides proceeded to essential completion according to the reaction

Jan 1, 1988

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

By Rui Mao, Ke-Xin Nao, Jian-Liang Zhang, Xiang-Nan Xu, Meng-Fang Wei

"In this research, fundamental characteristics of dust and sludge containing iron from the dusting system of sintering process, blast furnace, oxygen converter and rolling process in steel enterprise were studied by chemical analysis, X-ray diffraction analysis, optical microscope analysis, scanning electron microscopy analysis, particle size analysis and other analysis means. Development direction of resource utilization for dust and sludge containing iron from steel enterprise was put forward on the basis of above study.IntroductionDust and sludge containing iron for steel enterprise mainly come from the dusting system of sintering process, pelletizing process, blast furnace, oxygen converter, rolling process and other related process. Iron content of dust and sludge is between 30% and 70%, and they also contain certain content of carbon, calcium oxide, magnesium oxide and harmful elements [1-3]. Output of dust and sludge is determined by raw materials conditions, technological processes, equipment configuration and management level. Dust output in sintering process accounts for about 2% to 3% of the sinter production, while dust and sludge from iron making and steel making process respectively take up 3% to 4% of hot metal and crude steel production, and the solid waste from rolling process accounts for about 0.8% to 1.5% of the output of rolled products [4,5]. Dust and sludge contains Fe, CaO, MgO, C and other valuable resources, it will not only result in the waste of resources, but also cause serious pollution to environment ifthe dust and sludge are not recycled. China's crude steel production in 2012 is about 700 million tons and output of dust and sludge containing iron is nearly 60 million tons, so, it is of great significance to have a resource recycling for dust and sludge containing iron from steel enterprise."

Jan 1, 2014

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras, Chuanbing Wei

Bottom blown oxygen copper smelting process developed at Dongying Fangyuan Nonferrous Metals shows many advantages such as flexible feed requirement, high productivity, low energy consumption and high direct copper recovery. However, the weak acid generated during the process is not stable which influences the waste management and continuous operation. The amount of the weak acid is determined by SO3 formed in copper smelting process. SO3 can be formed inside copper smelting furnace and boiler at different conditions. Effects of temperature and oxygen partial pressure on the formation of SO3 during copper smelting process have been discussed thermodynamically. Understanding of the mechanisms for SO3 formation will enable the operation of bottom blown copper smelting furnace to be optimized and generation of the weak acid in the process can be managed. The fundamentals developed in this study can also be applied to other copper smelting processes.

Jan 1, 2016

By N. Can

Kinetics and mechanism of the chemical interactions between Si3N4 and TiC were investigated by isothermally reacting samples under nitrogen and argon atmospheres at temperatures between 1600°C and 1700°C? The initial composition of the powder compact contained 20, 30 and 40 volume per cent TiC? Kinetic analysis were performed by measuring mass losses and composition of the titanium carbonitride (TiC1-xNx) at predetermined time intervals? It was found that in the Si3N4-TiC system the degree and rate of the reactions increased with increasing temperature and content of TiC in both nitrogen and argon atmospheres? Si3N4 in the presence of TiC was stable in nitrogen atmosphere and the reactions were confined to Si3N4/TiC and TiC/N2 interfaces? At both interfaces interchange reaction occurs by simultaneous diffusion of nitrogen towards the centre of the particle and desoprtion of carbon in the opposite direction resulting in formation of titanium carbonitrides with various compositions? Reaction products under nitrogen atmosphere were B-SiC, TiCl1-xNx and N2? The maximum "x" value in TiC1-xNx was found to be 0?67 under nitrogen atmosphere? Si3N4 was found to be unstable in argon atmosphere in the presence of TiC and dissociated into liquid silicon and nitrogen gas within approximately four hours of reaction time, depending on temperature? The reaction mechanism in the initial stages of the interaction between Si3N4 and TiC under argon atmosphere proceeds similar to reactions under nitrogen atmosphere? However, considerable amount of Si3N4 dissociates within the first half hour? Liquid silicon aggressively attack both TiC1-xNx and unreacted or partially reacted TiC particles through cracks and pores and diffuses into interier part of the particle forming liquid solutions? After this stage, reactions under argon atmosphere proceeded according to Si-Ti-C ternary system?

Jan 1, 1999

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By William D. Riley

The U. S. Bureau of Mines has developed technology to recover by-product materials from aluminum scrap using engineered scavenger compounds (ESC). ESCs are structural oxides with a channel or tunnel structure that allows them to hold ions of a specitksizes and charges. The scavenging reaction is easily reversible allowing the ESC to be recharged for continued use and the ion is recovered as an electro deposit. Key features of this novel technology are; a) ESC ,systems are designed to have a high degree of selectivity for a desired ionic species. b) The recovered mater.ial requires little or no additional reprocessing prior to reuse. Two current uses for the ESC technology that are described in this paper are the removal and recycle oflithium (Li) from lithium aluminum (Li-AL) alloys; and, using ESCs as a replacement for the conventional demaging (magnesium removal) technology used by the secondary casting industry. Research indicates that the ESC technology proposed for both these applications has either 'distinct economic and/or environmental advantages over previously employed methods of recovering. metal values from aluminum scrap.

Jan 1, 1995

By Junzo Hino

Most of the waste that contains a small portion of copper is landfilled. The recycling process of copper from the waste, such as shredder residue, should be developed in order to save mineral resources and prevent environmental pollution. Shredder residue, generated from disposed automobiles and electric appliances, consists of many types of plastics, glasses and metals. The combustion heat of plastics is efficiently used for smelting in the recycling process that consists of melting and reduction. Because the waste contains numerous components the knowledge of the distribution behaviors of the main components is necessary to develop the recycling process. The distribution behaviors in the recycling process are evaluated by using the thermodynamic calculation program, HSC Chemistry. The calculation results are compared with the practical operation data of the recycling process and discussed.

Jan 1, 2003

By Claudio Parra De Lazzari

The determination of the governing step of the deoxidation rate and the effects of the hydrogen content of the mixtures (C), the diameter of the delivery orifice (4) and the Reynolds number of the orifice (Re.) on the product Av kjg were investigated. A,, is the total surface area of the interface between the bubbles and the melt and kjg is the mass transfer coefficient in the gas phase. The design of the experiments was based on a two level statistically fractionated, factorial planning. Oxygen in the melt was measured as a function of time. It was found that the governing step of the deoxidation rate was the transport of hydrogen in the gaseous phase and that {Ay kjg} increases with C, {o} and Reo.

Jan 1, 1997

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By W. W. Albrecht

I. Introduction Refractory metals like tungsten, molybdenum, rhenium, tantalum and niobium and their compounds are essential ingredients of our modern technology. Especially in purified form, they are used in special alloys, electronics, optics and ceramics. The processing route from raw material to high purity refractory metals and their compounds includes, as a prime option, the following steps: - dissolution of raw materials. - liquid liquid extraction. - precipitation of high purity intermediate compounds. - calcination/reduction to high purity oxides/metals. Especially in the first three steps, major amounts of chemicals like acids or sodium hydroxide are used and, as by-products, substantial quantities of residues and effluents are generated. The impact of environmental regulations on these by-products and the attempt to reduce or minimize the amount of residues and effluents produced will be discussed in this presentation using Ta/Nb chemistry as the example. The basis of our considerations will be the way these by-products are handled at HCST, a major, and in some cases, the biggest producer of refractory metals (tungsten, molybdenum, rhenium, tantalum, and niobium).

Jan 1, 1992

By A. Dadgar

Extraction of gold and silver from two refractory concentrates using cyanide and bromine reagents was reported at the 12th International Precious Metal Conference (1). The objective of this paper is to present the gold extraction, recovery, and economics for two refractory concentrates using cyanide and bromine reagents. Gold extractions for cyanide leaching (24- 48 hours) and bromine leaching (6 hours) were the same and ranged from 94% to 96%. Gold recoveries from bromine pregnant solutions using carbon adsorption, ion exchange, solvent extraction, and zinc and aluminum precipitation methods, were better than 99.9%. A preliminary economic analysis indicates that chemical costs? for cyanidation and bromine process are $9.50 and $10.50, respectively per ton of calcine processed.

Jan 1, 1989

By K. Potluri, S. Akella, S. Bhansali

"This paper presents the design and angular strength analysis of microneedles for use as a transdermal interface for drug delivery, fluid analysis and sampling etc. Microneedles of different dimensions were designed and fabricated using various materials viz. Si02, OxideNitride- Oxide (O-N-0). The design, modeling and analysis was done using the Finite Element Analysis (FEA) software ANSYS™ 6.1. Angular strength analysis of the microneedles was done using angular loading in ANSYS™, with the corresponding inaterial property settings. Using the force-displacement settings, forces of magnitudes in the range of 10 mN - 25 mN were applied on the microneedles at loading angles ranging from 30° to 90° was applied on needles. Square and circular shaped microneedles were modeled and the displacements and stresses generated were studied to characterize the angular strength of the microneedles. The buckling and force-displacement analyses show that O-N-O microneedles are more strong and robust as compared to needles of other materials. The analysis shows that while circular microneedles have uniform stress distribution, square microneedles have low stresses concentrated along the edges.INTRODUCTIONIn modem clinical and biomedical applications, drug delivery is done either by oral administration or by hypodermic injection. Hypodermic injection of drugs using needles is often painful. Hence, transdermal drug delivery techniques are increasingly being sought out as an alternative. In transdermal drug delivery the needles puncture the Stratum comeurn - the outermost layer of the human skin. The advantage of transdermal drug delivery (or transdermal measurement) technique, is that it reduces pain and tissue trauma."

Jan 1, 2004