Search Documents

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By Arthur E. Morris

Process modeling software is used extensively in process engineering, but there is a notable lack of affordable software for educational uses. This paper describes two educationally oriented software programs for thermochemical modeling of processes involving metals, minerals, and ceramic materials. Both programs run as Excel@ spreadsheet files. The first is FREED, a thermodynamic database program containing datafiles for 2500 species. It contains the entire U. S. Bureau of Mines and most of the U. S. Geological Survey database, plus data for scores of other species drawn from various sources. Several modules are available for manipulating and viewing the data. The second program is THERBAL, for making thermodynamic calculations using FREED data. Equilibrium calculations can be made for systems with non-ideal solutions, for a specified set of pressure, temperature, and input amounts of reactants. An optional heat balance is also calculated. The results are displayed as tables or charts in Excel worksheets. Examples of the use of THERBAL will be given for the reforming of natural gas for DRI production, DRI production, and EAF steelmaking. Some observations will be made on its use in the classroom. The development of FREED and THERBAL was initially carried out at the Department of Metallurgical Engineering, University of Missouri - Rolla as part of a project to preserve and enhance the Bureau of Mines database. The current versions were developed privately by the authors.

Jan 1, 2002

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By Ying Li, Xuling Chen, Xiaohui Fan

"In the sintering process, the behavior and performance of iron ores is extremely complex. Different minerals have different sintering properties. In order to use iron ores rationally and effectively, multilevel fuzzy evaluation method is used to establish the comprehensive evaluation model of iron ores. Because of the relative independent characters of iron ores in sintering process, the characters can be divided into physical and chemical properties, granulation performance, and sintering properties, are divided, and together with iron ores prices as the first level index for judging, which are used as the second level index for judging. Using the analytic hierarchy process (AHP) to determine the weight of each index, which is used as the second level index. The relative membership matrix is determined by triangular membership function, the comprehensive evaluation model is established.IntroductionIn China, sintering is the main method for iron ores agglomeration. Sinter accounts for more than 80% of the blast furnace. Sinter production in the iron and steel enterprises in China plays an important role[l-2]. As the main raw material of iron ores sintering, the objectivity and integration of iron ores evaluation is essential. The iron ores evaluation methods include of metric ton price evaluation method, iron grade of a single iron ores sintering, acid-base balance method, composition assessment method and other methods which are based on the chemical composition and physical properties of iron ores to measure the quality of iron ores[3]. The high-temperature mineralization is an important process in sintering process, which affects the structure and mineral composition of the sinter, and has a close relationship with the quality of the sinter[ 4]. Therefore, in consideration of the physical and chemical properties, granulation properties, mineralization performance and sintering properties, the iron ores are evaluated by multi-level fuzzy comprehensive evaluation. The multi-level fuzzy comprehensive evaluation method makes a comprehensive evaluation, applying fuzzy transform principle and maximum membership degree principle, considering a number of factors related to the things which are evaluated. The method has lower requirements for the amount of data, and which integrates qualitative with quantitative judgment. It has a unique advantage to make up for the deficiencies of traditional evaluation methods. It also can comprehensively evaluate the iron ores in a relatively short period, reduce a lot of experiments, improve efficiency and guide the sinter production[5-6]."

Jan 1, 2013

By Chris P. Pistorius

Over the past few decades the carbon intensity of ironmaking and steelmaking has been reduced considerably through improved efficiency in blast furnace ironmaking, partial replacement of coke with less carbon-intensive fuels, and increased use of scrap and direct-reduced iron in steelmaking. To evaluate possible further reductions in carbon intensity accurate process information is needed. A preliminary test of the fidelity of publicly reported data as a source of process information is reported here. The sources are industry roundups of electric furnace furnace steelmaking and blast furnace ironmaking (published by the Association for Iron and Steelmaking Technology), and data recorded by the Environmental Protection Agency under the US Greenhouse Gas Reporting Program. From a comparison for an integrated steelmaking plant and an electric furnace furnace plant, it appears that the values from the two data sources are consistent. The comparison does rely on process details such as the quantitative relationship between injected oxygen and carbon emissions in electric furnace steelmaking.

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Mark Cross, Andrew P. Campbell, Koulis A. Pericleous

"Computational Fluid Dynamics (CFD) modelling is being used to simulate the freeze layers formed within direct smelting processes. There has been some concern whether water-cooled elements can withstand the p~ocess conditions and in particular abnormal cases where they may be splashed in molten metal.To validate the models being developed, two cases from literature have been modelled for solidification and stress analysis. The solidification case is presented in detail and is for hot molten metal flowing through a cylindrical pipe. The walls are at a temperature below the melting point for the metal. The resulting solid (or freeze) layer is within 3% of the value calculated by Sampson & Gibson9 •Preliminary modelling of the refractory-slag interactions is presented. Although three basic mechanisms: Penetration; Corrosion; and Erosion will eventually be modelled, only the penetration is considered here. The corrosion mechanism is to be modelled by tracking the time that the penetrated refractory is at the required temperature.Future work, after adding all the required physics, will focus on the modelling of a water-cooled element placed lower in the smelter. Process perturbations will be simulated to examine what these elements will withstand."

Jan 1, 2001

By J. A. Eisele

There is currently much interest in how extraction of gold and silver from ores with acidic thiourea solution compares with extraction using alkaline cyanide solution. Agitation leaching tests were performed by the Bureau of Mines on 14 precious metal ores using sodium cyanide (?NaCN) and thiourea [(NH2)2CS) as extractants. The objective was to compare the results of the two extractants. NaCN was used at a concentration of 2 g/L with and without H202 as an oxidant. (NH2)2CS was used at concentrations of 2 and 20 gjL, and the solution potential was controlled at 390 to 420 mV standard hydrogen electrode (Eh) with Fe2(S04)3. With both reagents a.t 2 g/L extractant levels, NaCN extracted more gold and silver than (NH2liCS from all of the ores. At 20 g/L (NH2)2CS compared with 2 g/L NaCN, (NH2)2CS extracted more gold than NaCN from two ores, the same amount from one ore, and more silver from one ore. NaCN extracted more gold than (NH2 )2CS from 10 ores and more silver from 4 ores.

Jan 1, 1989

By Mike Adams

A comprehensive pre-feasibility study has been conducted by Companhia Vale do Rio Doce CVRD) for Niquel do Vermelho nickel laterite deposit. Within this study, five integrated flowsheet options were evaluated via batch and pilot campaigns at Lakefield Oretest, over an intensive six-month period from receipt of ore to final reporting. Key technical objectives set by the client included demonstrating the technical viability of the beneficiation of several ore types, processing through integrated pressure acid leach/mixed hydroxide precipitation (PALIMI-IP) and mixed sulfide precipitation (PALIMSP) circuits, and the treatment of barren liquors to meet stringent environmental requirements. Refining of the MHP was by ammonia re-leach and solvent extraction (SX) to produce LME-grade nickel cathodes, NiCO3, NiO and CoS. LME grade nickel and cobalt was also produced by oxidation of the MSP and hydrogen reduction on the leachate. The database and data acquisition system, along with web-based reporting, enabled rapid turnaround on both daily and more comprehensive run reports, making it possible for speedy and confident decisions on operating conditions of the complex flowsheets. The high value of developing such data is emphasized and discussed as pivotal in the successful progression of laterite projects through to sustainable commercial viability. Keywords: Flowsheet, CVRD, Nickel, Piloting, Pressure, Leach, Refining.

Jan 1, 2004

By C. G. Anderson, L. G. Twidwell

"Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.Fundamental Alkaline Sulfide HydrometallurgyHydrometallurgical methods can be employed for treatment of gold, arsenic, antimony, tin and mercury containing materials, concentrates and ores as well as complex ones containing any number of metals. The alkaline sulfide system is one of these and is essentially a mixture of sodium sulfide and sodium hydroxide. This is a unique hydrometallurgical system as it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic and mercury [1-7]. Worldwide, it is employed industrially in the CIS, China and the United States for the production of antimony [8-15].As an example, when the system is applied to an arsenic containing material like orpiment, As2S3, a solution of sodium thioarsenite is formed. This is illustrated as:"

Jan 1, 2008

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By E. Fregeau-Wu

The mineralogy and grain size distribution of phases in a steelmaking slag and experimental products from the heating of the slag under various conditions were determined to explore the possibility of recycling of the iron and manganese to the blast furnace. The steelmaking slags consisted of three major phases: dicalcium silicate, dicalcium ferrite, and Mg-Mn-wustite. Most of the phosphorus was contained in the dicalcium silicate and to lesser extent in the dicalcium ferrite. Due to the fine grain size of the dicalcium silicate, grinding and magnetic separation required pretreatment to increase the grain size and hence the liberation. Experiments on a steelmaking slag were conducted by heating the slag to 1633-1748°K( and slow-cooling in an inert atmosphere at various rates with or without the addition of fluorspar (CaF2) as a flux. Grain size distribution analyses of the starting material and the slow-cooled products were performed using the SEM-IPP area scan method and the QEM*SEM linear scan method. Comparable and reproducible results were obtained on the same sample using both methods. A size versus volume percent plot showed the increased grain growth most effectively. Examples of the grain size distributions obtained were used to show that a higher soaking temperature prior to slow-cooling, a slower cooling rate, and the addition of fluorspar to the slag promoted grain growth.

Jan 1, 1989

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Zdzislaw Miczkowski

At KGHM Polska Miedz S.A, a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass exchange inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed, The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ?The second zone moves slower into the grain and the rate of the movement is determined by the presence of oxygen, In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined, The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001

By Sanaz Mosadeghsedghi

The feasibility of the application of electrodialysis in separation of light and heavy rare earth elements (REE) in synthetic solutions was investigated. The experiments were carried out using single and binary solutions of a light (cerium) and heavy (ytterbium) REE. The effects of electrical voltage, electrical current, and the addition of complexing agent (EDTA) to increase the separation selectivity were investigated. Separation of Ce and Yb was achieved in binary solutions with and without the addition of EDTA. Higher degrees of separation were seen at higher voltages. Ce–Yb separation was more significant in the presence of EDTA. The separation factor of Ce–Yb and Ce–Yb-EDTA were 1.44 and 2.60, respectively.