Search Documents

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By Dave Forrester

Mining subsidence over shallow abandoned coal mine workings is unfortunately not an uncommon experience in the coalfields of North America and there is a significant knowledge and literature base addressing the phenomenon and related issues. From time to time, however, a case history arises which is outside the more routine occurrence. This paper addresses one such case and presents an overview of a subsidence Event above abandoned coal workings, which badly damaged a two-story High School building. The subsidence at the Cape Breton & Victoria Regional School Board (CBVRSB)'s MacDonald High School in Dominion, N.S., Canada on October 30, 2002 led to a detailed investigation. It was concluded that the ground movement and associated building damage had been caused by mining subsidence in underlying old underground coal mine workings of the 1890s, only 150 ft deep at the School. The Event was not isolated and a similar but smaller event happened nearby a few months later. The paper describes the events and summarizes the subsequent investigations and findings. The 17-year old High School building was eventually demolished.

Jan 1, 2004

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By Keith Heasley

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 in (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.'s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysts of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. `The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

Jan 1, 2001

By Nan Zhou, Jixiong Zhang, Qiang Zhang

"Mining activities under hard roof could easily induce rock burst. Based on the geological conditions of widespread hard roof in China, this paper discusses the type, mechanism of occurrence and prevention of rock burst caused by hard roof from energy evolution point of view. It analyzed the interaction between the solid backfilled body and roof under different backfilling ratios. And by establishing and applying the mechanical model, the deformation of hard roof and energy evolution of the panel under different backfilling ratios were determined, revealing the control effect of solid backfilling on disaster-causing energy. As a result, an innovative method using the solid backfilling method was proposed as a solution to the hard-roof-induced rock burst hazards. Moreover, mine trial was conducted in Panel 6304-1 of Jisan Mine. The result shows that the stress concentration factor of the front abutment stress was only 1.44; the coal dusts in drill holes didn’t exceed the limits and microseism of large energy didn’t occur during mining mining, indicating that solid backfilling mining could be applied as an effective method for preventing rock burst caused by hard roof.INTRODUCTIONSHard roof refers to the thick strata above the coal seam or thin immediate roof. It is strong with poor joint development. After mining, instead of immediate caving, it will overhang for a large area in the gob, resulting in high stress in front of the face and difficulty in gas dispersion. As a result, the face spalls, the roof exposes and the gas accumulates in the gob. With the continuing advance of the face and increase in area of overhang, the stress in the hard roof will eventually exceed its ultimate strength and cause a large area of caving, followed by quick release of energy concentrated in the roof and coal seam, which may cause rock bursts and other dynamic disasters in the mine as well as serious equipment damage and casualties. Therefore, the hard roof becomes one of the main factors causing rock bursts at the face.Hard roofs in China varies in conditions. It ranges from dozens of meters to hundreds of meters in thickness. However, coal reserve under hard roofs accounts for about 1/3 of the total reserve; moreover, nearly 40% of the fully-mechanized coal mining panels are those with hard roofs and more than 50% of the mining areas are associated with problems of hard roofs. Aiming at this problem, researchers at home and abroad have proposed many solutions, e.g. coal pillar support, strength weakening and forced caving, to prevent rock bursts caused by hard roof. These solutions have been employed in some cases with good results. However, due to the variability in geological conditions of mining and hard roofs, the application of the above solutions is limited."

Jan 1, 2015

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

By Frank E. Chase

Sacrificial entries, roof slotting, and other tactics have been used to combat high horizontal stresses during roadway development in U.S. coal mines. In Australia, the "pillar extraction on the advance" mining method has been successfully employed as a horizontal stress control technique. The concept of advancing and relieving mine workings through pillar extraction developed from observations that some mines experience difficult ground conditions when advancing and retreating the first panel in a new reserve. However, conditions dramatically improve in subsequent panels. Apparently, the creation of a gob area stress relieves the adjacent panel workings. After much debate and close scrutiny, the first U.S. roof control plan to advance and relieve was approved in 1998, for the Sargent Hollow Mine in Wise County, VA. The major concern was that this mining practice places section personnel inby of the gob. The tentative approval permitted barrier pillar slabbing and removal of the adjacent development pillar during panel development. The intent of the plan was to provide a "stress shadow" for the advancing faces and outby workings to reduce the excessive number of roof falls. Sargent Hollow successfully extracted their first panel by pillaring on advance and retreat mining using posts. Mobile roof supports were employed to extract pillars while advancing the second panel. This paper summarizes Sargent Hollow Mine's experiences with the advance and relieve mining method.

Jan 1, 1999

By Richard J. Perin

Subsidence monitoring was conducted in proximity to the 1-A and 2-A longwall panels at Consol Pennsylvania Coal Co.'s (CPCC) Bailey Mine slurry impoundment. Monitoring fullfills federal Mine Safety and Health Administration (MSHA) mandated requirements. Construction of the monitoring network was completed between May and June, 1986. Monitoring was conducted before, during, and after mining of the panels between June, 1986 and February, 1987. The embankment was not deleteriously impacted by longwall mining.

Jan 1, 1988

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Kanaan Hanna

Abandoned mines pose a serious threat to public health and safety, as well as the environment. When active workings approach old mine workings, miners could encounter significant hazards. Additionally, the presence of mined-out areas or voids underlying residential/commercial properties, transportation, and infrastructure systems can cause subsidence issues ranging from differential settlements and sinkholes to catastrophic collapse. All these features can result in adverse impacts in terms of cost and public safety. Traditionally, mine void detection and related engineering investigations for mine subsidence risk assessment and mitigation have been greatly dependent on systematic drilling and grouting backfill programs. The unknown location and condition of abandoned underground mines represent significant challenges to geologists and engineers in accurately evaluating subsidence hazards and developing appropriate mitigation measures. A comprehensive, multi-phase mine subsidence investigation was conducted at an abandoned western U.S. mine site. The mine operated in an approximately 8-ft (2.4-m) -thick coal seam using room-and-pillar extraction from 1919 to 1922. The mine lies at depths ranging from 50 to 100 ft (15 to 30 m), and it is overlain by critical pipeline and utility corridors. Any future subsidence/ sinkhole that occurs beneath or adjacent to the corridors could pose a significant threat, specifically to the structural integrity of the pipeline corridor. Therefore, the engineering geophysical investigation was initiated to determine the potential subsidence risk. This paper describes a recent success achieved by using integrated engineering geophysics in subsidence risk evaluation. A summary of significant results with emphasis on subsurface characterization, mine workings and voids delineation, modeling analysis, and high risk zones identification and mitigation strategy is presented.

Jan 1, 2011

By Timothy Ross

The Pittsburg & Midway Coal Mining Co.'s Kemmerer Mine is one of the deepest surface coal operations in the world, with the highwall extending to approximately 1,000 ft above the pit floor. To increase recovery, auger mining is being evaluated beneath the highwalls of several seams representing the current economic limit of pit development. The primary augered seam is over 50 ft thick, can approach 100 ft thick, and dips into the highwall at an average of 17 degrees. The seam thickness and dip present many geotechnical design and operational challenges for multiple Sup to five) lift augering. This paper presents the design criteria and methodology applied to determine appropriate web and septum thicknesses for the various cover depths anticipated, as well as operational measures that can be taken to increase overall coal recovery. The primary tool used in the design was the finite difference code FLAG. Models incorporating typical strata sequences associated with the coal seam were run at several different cover depths corresponding to the maximum anticipated auger penetration. Web and septum thicknesses were varied until the minimum thickness satisfying a given safety factor criterion was determined. Using this procedure, design curves were developed for web and septum thickness versus cover depth. Operationally, several recommendations were developed to ensure that overall coal recovery is maximized. By angering across the scam dip, auger penetration per hole can he increased dramatically, and by carefully planning maximum planned auger penetration versus hole spacing, increased coal recovery can be safely attained.

Jan 1, 1999

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995

By Zhou Ying

Based on the mining condition and roof lithology of the 2-3 coal seam at Gengcun Mine, the simulated materials modeling method was used to study the movement process and characteristics of overburden strata movement and to analyze the movement laws of overburden strata during top coal caving mining. Based on the modeling results, variation of the peak abutment pressure and its effect on the top coal's crushing and caving in the mining process was discussed.

Jan 1, 2001

By Alan Bugden

Goedehoop Colliery produces 8 million tonnes of coal a year, principally from room and pillar mining, and is situated in the Witbank Coalfield in the Republic of South Africa. The mine has a long and successful record of producing export quality coal from the 2,4 and 5 seams at depths ranging from 20 to 100 metres using modem mining equipment. Following a number of fatalities caused by large and unexplained roof falls in roadways and intersections of supported ground, a review of the roof control system at Goedehoop was carried out. This led in turn to a programme of underground measurements and surveys. This included detailed investigation of the roof falls, horizontal stress mapping, stress measurement and short encapsulation pull testing on roofbolts. These investigations led to a number of important conclusions in relation to the state of stress in the ground, the roof failure mechanisms, standard of rootbolt installation and performance of the roofbolt system. As a result of the work Goedehoop Colliery has made a number of substantive changes to the roof control management system at the mine. These include: 1. A recognition of the importance of horizontal stress as the main factor responsible for roof falls. 2 The forward planning of roof support based on known features which cause the stresses to be elevated. 3. The introduction of a more effective roofbolt system, which can be more easily installed to a high standard. 4. A response system based on risk assessment and monitoring roof movement on a routine basis. The paper describes the knowledge acquired, the conclusions drawn, the changes made and progress to date.

Jan 1, 2001

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By Frank E. Chase

Geologic structures have been responsible for numerous underground accidents and fatalities, and are a constant-source of down time. During - longwall mining, ground control problems associated with geologic anomalies are aggravated by the abutment pressures which develop as the panel is retreated. Therefore, it is imperative that these structures be recognized and properly supported in head- and tailgates. Fractures, faults, clay veins, igneous dikes, and ancient stream channels (paleochannels) disrupt the lateral continuity of the mine roof and can cause falls in gateroads. Horsebacks and kettle bottoms are also hazardous because abutment pressures tend to "pop out' these structures into the gateroads. This Bureau of Mines investigation describes the physical characteristics associated with hazardous geologic structures, identifies the coal fields where-they have been observed, and, where possible, suggests support strategies and other mine plan modifications to help minimize their effect.

Jan 1, 1990

By Stephen P. Signer

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to ( I) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Jan 1, 1997

By Nicholas Chlumecky

One of the most dangerous jobs in mining is that of resupporting the roof after a fall has occurred. The resulting cavity may be more than 30 feet high, with relatively unstable sides and roof. It is often impossible to proceed with rehabilitation without exposing men and equipment to unsupported rock. Temporary supports provide margin- ally effective protection because of the lack of available footing. Furthermore, the usual supports in rehabilitated fall locations are not permanent, require frequent maintenance, and fail to eliminate some remaining serious safety hazards. This is typically the case for high cavities where loose rock drops from considerable heights from between roof bolts. Supports made of cribbing, beams and additional cribbing to the high points of the fall in many cases do not provide good protection due to the deterioration and shrinkage of timber. In mines, high cribbing frequently loses contact with the roof and thus provides no protection against rocks peeling off the sides. This is true in spite of the fact that at time of installation the cribbing was wedged tightly to the roof. Therefore, when considering the difficulties which occur with current practices, the objective is to find alternate methods of resupporting the high roof after a fall.

Jan 1, 1981