Search Documents

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By M. Hepokoski, M. Klein, L. Yan

"NIOSH research has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives (RAs). These high temperature and humidity levels inside an RA may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics to create detailed thermal simulation models of RAs with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine RA. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 95°F apparent temperature limit for RAs is reasonable. The results indicated that the 95°F apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicated that the body core temperature did not reach dangerous levels even at an apparent temperature of 130°F. However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were increased, the water provided in an RA would have to be increased to offset moisture loss. INTRODUCTION The purpose of this effort was to predict a miner’s core temperature and moisture loss (sweating and respiration) in environments that are likely to be encountered in a coal mine refuge alternative (RA). A range of temperatures and relative humidity were studied to determine whether the current 95°F Steadman apparent temperature (AT) limit and 2.25 quart/day water requirements for RAs as mandated by the Mine Safety and Health Administration (MSHA) are reasonable [1, 2]. The effects of metabolic heat rate (activity level), miner size (height and weight), and pose (sitting or lying) on core temperature and moisture loss were also studied. MODEL DESCRIPTION TAITherm thermal modeling software (ThermoAnalytics, Inc.) was used to simulate humans in RA-like environments within a range of temperature and relative humidity combinations. The TAITherm Human Thermal Model (HTM) predicts the dynamic thermal response of the simulated miners while accounting for clothing, human tissue thermal properties, and active thermoregulation. The following sections describe the HTM in more detail, the thermal model setup for this analysis, and core temperature and moisture loss metrics found in published literature. Human Thermal Model Overview The TAITherm human thermal model was used to simulate the heat generated by the shelter occupants, and to predict the miners’ skin and core temperatures along with their sweat evaporation rates. The thermoregulation model simulates the process by which the body attempts to maintain a constant core temperature by considering the effects of shivering, sweating, and changes in skin blood flow. This model calculates surface and deep tissue temperatures within the human body as described by a surface mesh."

Jan 1, 2017

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By David Butts

Solar ponding to crystdlize sodium chloride has been used for thousands of years.1 The systems used were inefficient and usually small compared to the large 25,000 acre pond areas seen today. It has only been in the last 25 years that any real effort has been applied to develop solar ponding technology. Many large solar pond systems have been constructed without much thought to efficient and optimum production rates. The recent high costs of labor, of equipment and of energy have forced producers to take a closer look at their solar pond systems in an attempt to squeeze out the highest possible yields. Other companies such as the Arab Potash Company, the Dead Sea Works, Texas Gulf (Moab, Utah) and San Francisco Salt Companies have no more land area in which to expand and therefore efficient ponds are essential. This paper is written to show how the subdivision of solar ponds can result in production increases of up to 20% and beyond.

Jan 1, 1984

By W. E. Heinrichs, R. W. Davis

Introduction Cross borehole seismic tomography (CBST) is a geophysical technique that allows definition of the distribution of some physical rock property between two boreholes. The method is similar to the computer-assisted tomography (CAT) scans used by the medical industry. This paper describes the method, its applications and the developing trends in its use that interest the mining industry. The idea of using tomography in connection with geophysical methods for measuring rock properties between boreholes has been around for three or four decades. Until the advent of high-speed, large-capacity computers, the necessary calculations were too formidable for production use. Another factor in the development of the technique has been the refinement of a mathematical base to meet the needs of the medical industry. The geophysical applications have benefited from this refinement. An extensive discussion of the basic theory is given in Kak and Slaney (1988). CBST, although widely researched and written about, is still not extensively put to use in mining and engineering projects. Most real world examples in the literature have come from research carried out by government laboratories or by large companies. An exception is the regular use by Prospection Geophysique Francaise (Cottin et al., 1986) in damsite investigations. The Japanese appear to be doing extensive research and testing of CBST's uses in civil engineering projects (Saito et al., 1988). Canada is researching the use of the method in connection with nuclear waste site investigations (Wong et al., 1987). Finland has tested the method in connection with a foundation investigation for a nuclear power plant (Cosma et al., 1984). In the US, the US Bureau of Mines has taken an interest in using CBST as a means to enhance in situ mining operations (Tweeton, 1988). Major oil companies are examining the method as a tool in oil field development (Justice et al., 1989). Description of the method CBST involves placing a series of receivers down one borehole and recording transmissions from an energy source placed successively at a series of positions in another hole. The objective is to generate a dense network of seismic raypaths between the holes. The denser the network of raypaths, the better the features between the boreholes are resolved. Either seismic travel times or sine wave amplitudes are measured by the receivers. Analysis of travel times between boreholes develops a picture of rock velocities between the holes. Analysis of seismic wave amplitudes develops a picture of the distribution of energy transmission characteristics between the holes. These seismic properties can be used to define occurrences of fracture zones, lenticular sequences or other important geologic data not apparent from examination of the borehole logs. When longitudinal (compressional) and transverse (shear) waves are analyzed, the physical properties, such as elastic moduli, can also be mapped. When wave amplitudes are measured, rather extensive corrections to the data are necessary. There is some disagreement among researchers as to the feasibility of making some of the corrections. For this reason, this paper will concentrate primarily on travel time analysis. Wave amplitude analysis will be mentioned occasionally only in passing. This does not mean that amplitude analysis does not provide important data on rock parameters, only that for the present there are limitations on its uses. Vertical seismic profiling (VSP), extensively used in recent years in oil exploration, is similar to CBST. Instead of using two boreholes, however, the VSP method uses an array of seismic sources or detectors down one hole and an array of detectors or sources along the surface radiating outward from the hole. While adequate for determining vertical velocity distributions, the VSP method is not, by itself, suitable for most engineering or mining projects. Computer programs used to analyze the field data make use of the fact that the total travel time or change in signal amplitude between boreholes is described by Dines and Lytle (1979) as: [9k = f Rk f( x,Y) ds (1)] where gk = the total time or attenuation along the kth ray path,

Jan 1, 1992

By Richard J. Lundin

Literature research is an inexpensive, yet effective tool for the direct discovery of ore deposits. Case studies abundantly demonstrate that properties with viable mineralization and *proven reserves have been overlooked, forgotten. or ignored and can be rediscovered by inexpensive literature search techniques Areal studies s as WaIlaby Enterprises Mining District Data Base Program appear to be more effective than traditional commodity studies. The success of such studies depends on the inclusion of Mineral Clairant Questionnaire Data, Mineral Ownership Data, Field Examination Data and the continual updating of all information. Such studies are valuable for proposed or existing Wilderness Area Evaluations.

Jan 1, 1977

By Clifford R. Porter

A 200 pound per hour Magnex Pilot Plant was designed and constructed. A non-compliance Eastern Coal which would generate more than 2.0 lb of SOZ per million Btu upon burning was brought into compliance (less than 1.2 lb of S02 per million Btu) during continuous operation of the pilot plant. Approximately 85 percent of the pyritic sulfur was removed while recovering 86 percent of the Btu of the feed coal. Pilot plant operation is summarized and preliminary economics presented. Present status of the Magnex Program is reviewed.

Jan 1, 1977

By F. C. Townsend

Centrifugal modeling was used to evaluate reclamation schemes of; (a) flocculants, (b) sand/clay mixes, (c) flocculants/sand addition and (d) capping with sand or sand/clay mix. Results suggest the hierarchy of effectiveness is: (d) capping, (b) s/c mixes, (c) flocculants/sand addition and (a) flocculants. Comparisions between currently used large strain consolidation computer programs reveal no difference between piecewise linear or finite strain calculations. Correlations between numerical and centrifugal model predictions reveal excellent agreement on magnitudes; however, rate predictions require improvement in laboratory input data and centrifugal scaling relationships.

Jan 1, 1987

By Donna Wallace

Past EPA groundwater monitoring programs required that contamination not leave the boundaries of a disposal facility. New regulations under the Resource Conservation and Recovery Act (RCRA) require that once hazardous waste constituents are detected beyond the limits of the disposal area, a program to define the rate and extent of contaminant migration must be instituted. Future regulations are likely to include even more stringent groundwater protection criteria. The implications of both the existing and probable future groundwater protection and monitoring requirements in terms of using geologic containment as a means of disposing of hazardous waste are explored in this paper.

Jan 1, 1981

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., under contract to the Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1986

By P. Wearden, K. Bryner, K. Vrana, V. Castranova, R. Dey, R. Reist, J. Blackford

INTRODUCTION Proliferation and enhanced synthesis of collagen by pulmonary fibroblasts have been shown to be key steps in the development of chronic silicosis (Goldstein and Fine, 1986). The regulation of lung fibroblast proliferation by cytokines released from alveolar macrophages may be an important pathogenetic mechanism in the development of the fibrotic process (Kelley, 1990). One cytokine, platelet-derived growth factor (PDGF), promotes fibroblast proliferation by inducing the movement of quiescent (Go) cells into the C1 phase of the cell cycle (Chen and Rabinovitch, 1989). Others regulate the rate of transition of fibroblasts from Gl into the S phase (Leof et al., 1982). These two classes of cytokines have been termed, respectively, competence and progression factors. One approach used to examine the release of cytokines from macrophages is the fibroblast proliferation assay in which fibroblasts are exposed to culture supernatants from macrophages exposed to various stimuli. In most of these assays, the supernatant contains fetal calf serum which provides the competence factor(s) necessary to facilitate the proliferation of fibroblasts (Bitterman et al., 1982; Bitterman et al., 1983; Elias et al., 1988). Recently, a fibroblast proliferation assay using plateletpoor plasma (lacking competence factor(s)) as a substitute for fetal calf serum has been described (Kuman et al., 1988; Bauman et al., 1990). In this assay, the release of a competence-inducing PDGF-like growth factor from rat and human macrophages can be distinguished from other cytokines that act as progression factors. In order to obtain more consistent results and with the ultimate goal to be able to discriminate between the effects of competence factors as opposed to progression factors, we have conducted experiments to determine the appropriate concentrations of plasma and PDGF required for imparting competence in the fibroblast proliferation assay. We tested lung fibroblast cells obtained from explants of rat lung tissue and also a fetal human lung fibroblast cell line obtained from American Tissue Culture Collection (ATCC153). MATERIALS AND METHODS Fibroblasts Specific pathogen-free, male Sprague-Dawley rats were use in some studies. Animals were given a lethal intraperitoneal dose of sodium pentobarbital. Fibroblasts were isolated by chopping the lung in enzymes that digest the connective tissue but liberate lung cells for further study (Rabovsky et al., 1989). After digestion, the remaining lung tissue suspension was filtered through two layers of sterile gauze and centrifuged to recover lung fibroblasts. These were resuspended in culture medium that contained 10% fetal calf serum and distributed to culture plates for growth. In other experiments, a human fetal lung fibroblast cell line, obtained from American Type Culture Collection, Rockville, MD, 20852, was used instead of rat lung fibroblasts. In these cases, a 1 ml ampule containing human fetal fibroblasts was plated into a tissue culture flask containing medium plus 10% fetal calf serum. For both types of fibroblasts, culture medium was changed 3 times per week and cultures were incubated at 37°C until confluent. Harvested rat and human lung fibroblasts were quantified using an electronic cell counter equipped with a cell sizing attachment (Coulter Electronics, Inc., Hialeah, Florida). Tritiated Thymidine Incorporation The basic procedural outline of Kumar et al. (1988) was used with modifications to evaluate tritiated thymidine incorporation into fibroblast DNA following exposure to PDGF and plasma. Both rat and human lung fibroblasts were plated at 50,000 cells/ml at a density of 250,000 cells/25cm2 culture plate. Cells were quiesced for 4 days with 2% rat plasma. As the assay was refined, fibroblasts were quiesced in plasma-free media for 48 hrs, since the mitogenic activity of 2% plasma was variable. Test medium was applied for a period of 6 hrs, followed by a 24 hr tritiated thymidine (lµCi/ml) labelling period in plasma-free media. Medium alone was used as a negative control and media with 10 or 20% fetal calf serum was used as the positive control for rat and human fibroblasts, respectively. Cell Quantification and Measurement of Mitogenesis Twenty-four hours after the addition of tritiated thymidine, the fibroblasts were washed with 5ml of fresh serum-free media, centrifuged and resuspended in phosphate-buffered saline. The cells were dissolved in 0.5m1 of O.1N NaOH and radioactivity determined in a beta counter. Incorporation of trititaed thymidine as an index of DNA synthesis was expressed as DPM/fibroblast. RESULTS In the present study, we quantified mitogenic potential by monitoring the incorporation of tritiated thymidine as

Jan 1, 1991

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995

By Paweł Stefaniak, Natalia Duda-Mróz, Sergii Anufriiev, Wioletta Koperska

Due to the high environmental risks and negative impact of a failure, tailings storage facilities (TSFs) need constant monitoring. Advanced mathematical models have been developed in the past to predict the behavior of TSFs and raise alerts if needed. To be precise and reliable, such models need a spatial distribution of soil types within the dam as an input. Getting this data from laboratory measurements is time and costconsuming. In this article, we propose an ANN-powered algorithm, which allows us to accurately estimate the soil distribution based on a cone penetration test (CPT).

Jun 25, 2023

By J. R. Arnold

The problem of recovering gold from a cyanide solution has been plaguing metallurgists since the cyanidation process was discovered in Glasgow, Scotland.1 The "perfect" method has never been found and this paper will not purport to fill that gap. But we, at Gold Fields, feel that we have developed a workable, cheap and efficient method of producing a refinery - ready product that has several distinct advantages over conventional electroplating techniques. The Gold Fields replating system is presently being used at their Ortiz and Mesquite operations. In short, the system electroplates the gold out on stainless steel wool, instead of mild steel wool as is usually done, then replates the gold by reversing the current onto stainless steel plates. By doing this the steel wool can be reused many times, the gold can be scraped off the plates cleanly and quickly, the operating costs are reduced and the slag production is greatly reduced.

Jan 1, 1986

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By Christopher Mark

Successful longwall gate entry design requires control of both vertical and horizontal stresses. Vertical, or overburden, stresses are most severe in the tailgate where they are concentrated by longwall panel extraction. Horizontal stresses, which are generally tectonic in origin, can be highly destructive during the development and headgate phases of longwall mining. The goal of this paper is to present the current state-of-the-art in detecting and controlling horizontal stresses. The information presented was collected through site investigations at 45 U.S. longwalls and an international literature review. The paper begins with a discussion of the present knowledge of regional in situ stress fields in the U.S. A review of available underground stress measurements from coal mines is presented, along with data collected by structural and petroleum geologists. The combined evidence indicates that a persistent ENE-EW trending stressfield is present throughout the eastern coalfields. Experience with horizontal stress in longwall mines is addressed next. The paper focuses on the northern Appalachian region, where the effects of horizontal stress have been most evident. Three case histories are discussed in detail, and the solutions each developed are highlighted. Observations made in the Southern Appalachian, Alabama, and Illinois coalfields are also described.

Jan 1, 1991

By Mark Kuchta

A new database application for long term production scheduling has been developed for LKAB&apos;s Kiruna mine. The scheduler uses a new block data structure whereby the monthly production data for three raw ore products are predetermined on a month-by-month basis for each production area that could be mined within the schedule time horizon. The production schedule is created by assigning the starting dates to the each production area subject to various mining operational constraints such that that the monthly deviations for the production targets are minimized. The system is well integrated into the mine&apos;s overall computerized mine planning system.

Jan 1, 2002