Search Documents

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By M. Churchill, V. R. Degner

Over the past two decades, declining ore body grades and increased operating and construction costs have provided an incentive for the development of progressively larger flotation machines. As a result, the 1.7-2.8 m3 (60-100 cu ft) flotation machine of the 1950's and 1960's is being rapidly replaced by large volume machines. The result has been improved flotation machine specific capacity (tph processed per sq ft of floor space); specific power (hp per tph processed); and process control simplicity. The recent development and satisfactory plant evaluation of the 28 m3 (1000 cu ft) flotation machine allows economic and operating advantages in high tonnage mill applications. Some principles of mechanically induced air flotation and the development of the large 28.3 m3 (1000 cu ft) flotation machine are reviewed here. Performance evaluation in beneficiating metalliferous ores-copper, zinc, and iron-is also given and recently completed plant results provided. Mining lower grade ore bodies results in the need to process increased tonnage in the concentrator. This greater tonnage requires more individual flotation machines, unless individual machine capacity, or cell volume, is increased. As the ore processing rate of the concentrator increases, the benefits of progressively larger individual cells in the flotation section become more significant. The accompanying figure illustrates the advantages of a larger flotation machine. In the figure, the number of machines in the rougher-scavenger section is related to the plant tonnage for three sizes of flotation machine: 8.5 m3 (300 cu ft), 14.2 m3 (500 cu ft), 28.3 m3 (1000 cu ft). The 28.3 m3 (1000 cu ft) flotation machine results in 95 fewer machines, compared to the 8.5 m3 (300 cu ft) machine at 45.4 kt/d (50,000 stpd) feed. The flotation cell reduction is, of course, doubled at a plant production rate of 90.7 kt/d (100,000 stpd). Using fewer flotation machines saves floor space. The 14.2 m3 (500 cu ft) and the 28.3 m3 (1000 cu ft) machines result in a floor area reduction, relative to the 8.5 (300 cu ft) machine requirements, of 134.7 and 418.1 m2 (1450 and 4500 sq ft), respectively, for the 45.4 kt/d (50,000 stpd) rate and 269.4 and 836.1 m2 (2900 and 9000 sq ft), respectively, for the 90.7 kt/d (100,000 stpd) rate. In addition, flotation practice has shown that the "specific power intensity"-power per unit cell volume-is less for increased cell size. This results in a power draw reduction, for the rougher-scavenger circuit, of between 552 and 686 kW (740 and 920 hp) for the 14.2 and 28.3 m3 (500 and 1000 cu ft) machines, respectively, when processing 90.7 kt/d (100,000 stpd). Fewer cells improve machine control and simplify maintenance needs while reducing floor space and power requirements. These are tangible incentives for the development of large flotation machines for high tonnage applications. Flotation Principles The accompanying figure shows how key hydrodynamic regions influence the performance of a mechanically induced air flotation machine. Air is induced into the fluid from the top of the cell, due to the mechanical action of a rotating impeller. The impeller circulates the liquid, or pulp, from the bottom of the cell. The result of these dual flow paths is the mixing of the two fluids and one solid phase in the highly agitated region where physical contact between the air bubbles, and the solid particles to be floated, is accomplished. The particle to be floated is assumed to have a properly prepared hydrophobic surface prior to flotation. Upon leaving the three-phase mixing region, the "floatable particle-air bubble matrix" and

Jan 7, 1982

By R. E. Doerr

The successful technical demonstration of coarse coal slurry transportation at Consolidation Coal Company's Loveridge Mine in West Virginia suggests that it is now appropriate to seriously consider this technology in other applications, especially the transport of ' coal in surface mining. Early examination indicates that coarse coal slurry transport may be highly competitive with existing haulage systems, depending on a number of factors. These factors are not yet completely defined, but certainly will include production rates, coal physical and chemical properties, terrain, soil conditions, climate, water availability and quality, availability of skilled labor and other economic considerations impacting the existing haulage systems.

Jan 1, 1983

By B. K. Mishra

Power draw of the mill has been accepted as an indicator of the performance of the mill, yet the problem of predicting power under a given set of mill operating conditions still remains to be solved. In the literature, this problem of predicting power is attributed to a lack of knowledge with regard to the motion of the charge. Here a DEM based model is used to analyze the motion of the charge. The resulting information is used to predict the power draw of the mill. A 16-ft diameter mill is simulated. A factorial design study of the variables-mill speed, lifter configuration and ball size distribution-as independent variables is taken up. The power draw as a response variable is analyzed to establish the best operating condition of the mill.

Jan 1, 1993

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, R. M. Papini, P. R. M. Viana, F. P. C. Silvas

The kinetics of atmospheric sulfuric acid leaching from a Brazilian nickel laterite ore was assessed using distinct reducing agents and ore mineralogy. This transitional ore contains 1.63% Ni distributed as 1.27% in coarse size (− 500 + 150 μm), mainly as silicates (lizardite and chlorite—28.6%), and 2.06%in the fines fraction (− 75 μm), mainly as iron oxy-hydroxides (goethite and hematite—49%). The effects of temperature, acid concentration, reducing reagent type, and concentration were evaluated. The − 75 μm fraction limited the leaching efficiency and the use of reducing media with thiosulfate improved leaching and Ni-Fe selectivity. However, at constant Eh of 626–743 mV and a pH range between 0.2 and 1.1, no substantial rise in metals extraction, except for Co and Mn, has been observed. In order to determine the process control at 95 °C, two regions in the extraction curves were used in combination with the shrinking core model. Control by porous diffusion was observed and the kinetic constant was found to be in the order kFe<kNi<kMn<kCo<kMg for atmospheric leaching without Eh control. In reducing media for the first 15 min of leaching, the kinetic constant was found to be kFe<kNi<kMg≅kCo<kMn as derived from Ni disseminated into iron oxides structures.

Oct 7, 2020

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By John Hickey

Management teams at mining companies begin to ask themselves whether to take a company public and, if so, how to do it as they approach the normal threshold for going public in terms of revenue and operating performance. Today, the expense of going public generally suggests the company has at least $20 million in annual revenue and at least $2 million in cash. The revenue number can be lower for mining companies with large reserves. In order to properly attract the investing public, the company must also be operationally strong with robust prospects. The company should have a strong management team and a consistent history of double-digit growth that will continue into the foreseeable future. Assuming the thresholds are met, a company?s management needs to weigh the pros and cons of going public.

Jan 1, 2012

By Walter Meintrup

On Nov. 4, 1981 the newly installed 1000tph wet-process iron-ore ball mill of A/S Sydvaranger completed its first four months of uninterrupted, successful full-load operation in Kirkenes/Norway. This 6.5m diameter mill is driven by a gearless ring or wrap-around motor of 8100kW at 13.1RPM - a first of a kind in this segment of industry. (Fig. 1) This paper analyses the reasons that have led to the selection of this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes in some detail the installation in Norway. General aspects of possible design variations, and application information for designers and users of such mills conclude the presentation.

Jan 1, 1982

By Levent Ozdemir, Charles Merguerian

Between 1996 and 1999, a high-performance Robbins TBM [235-282] excavated a 5 mile long, 23´2? wide, and ~700´ deep tunnel through the subsurface of southwestern Queens. Low penetration rates (~6´/hr [actual] vs. ~9´/hr [anticipated])resulted from changed rock mass conditions mostly attributable to high-grade metamorphism of the rocks. Over a three-year period, as-built circumferential geologic mapping (scale 1?=10´) and digital imagery of the tunnel, fracture and fault analysis, structural, lithologic, and petrographic studies have shown that the rocks of the Queens Tunnel consist of orthogneiss of mesocratic, leucocratic, and mafic composition. These metaigneous rocks developed coarse-grained fabrics during Grenvillian (~1.0 Ga) granulite facies metamorphism, and retained their nearly anhydrous, poorly foliated character during subsequent high-grade Ordoviciande formation. Lacking a penetrative foliation, the coarse granoblastic rock texture and extraordinary garnet content (up to 50% in some zones) together proved animpediment to efficient chip production and resulted in bimodal production of blocks and excessive fines. TBM excavation of the Queens Tunnel was also hindered by geological conditions that included unexpected lithology and rock fabric orientation, a zone of crosscutting hypabyssal rhyodacite dikes, and unanticipated extent of brittle faults. The dikes and brittle faults produced blocky ground conditions and a collapsing face condition that produced cutter damage and decreased utilization. Such fundamental textural, mineralogic, and lithologic control over hard-rock TBM penetration can be predicted by careful pre-bid geological analysis. To determine the causes of lower than anticipated TBM performance, a detailed investigation was carried out that included analysis of operational data from the TBM data logger and an extensive laboratory test program on cores retrieved from tunnel walls. Integrated laboratory testing included punch, point load, tensile strength, Cerchar abrasivity, and linear cutting tests, independent petrographic analysis and machine performance analysis. These allied investigations have provided quantification that the rock mass exhibited an unusually high degree of toughness and rock directional properties and established geological causes for decreased TBM penetration rates.

Jan 1, 2003

By Jeffrey M. Christian

Gold prices are rising, in what is coming to be seen as the beginning of a longer term upward trend. After languishing between $325/oz and $364/ oz from early 1991 into early 1993, prices began rising in the first half of 1993. Gold rose from a low of $326/oz in March 1993 to $414/oz on an intraday basis in early August. There was a speculative sell-off at that point, which took gold prices quickly back down to $350/oz briefly in October 1993. At that time, there still was a fair degree of skepticism about gold&apos;s price prospects. Many banks believed that gold prices could not mount a sustained rally. As prices dropped in August and September of last year, these suspicions seemed to be confirmed. Gold prices quickly rebounded, however, reaching $395/oz by early January 1994. The strength of this renewed increase led many banks, investors and others that had held negative views of gold to grow more positive. They began buying gold and trading it from the long side of the market. The result was that gold prices remained strong during the first quarter of 1994, trading between $375/oz and $390/oz.

Jan 1, 1994

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

The authors provide a discussion of the paper, ?Coal workers? pneumoconiosis prevalence disparity between australia and the united States,? a peer-reviewed paper that appeared in the technical papers section of the July 2012 issue of Mining Engineering magazine. The original authors, G.J. Joy (gjoy@cdc.gov), J.F. Colinet (jcolinet@cdc.gov) and D.D. Landen (dlanden@cdc.gov), respond.

Jan 1, 2013

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

Improvements in computer technology and associated software have allowed the improvement and development of more advanced ventilation modeling software packages including those that have the ability to simulate the effects of a mine fire on the ventilation system in terms of heat, smoke and gas distribution. This ability has real applications for the mining industry in terms of emergency planning, training and response. The primary focus of this paper will be the benefits to training programs that this type of software can provide to all types of training for various personnel, from the newly hired inexperienced miner, mine rescue, atmospheric monitoring personnel and emergency evacuation drills. The results of the simulations can then be used to give miner?s more detailed information on what types of conditions they may face based on the type and location of the fire and the program itself can be used to manipulate the ventilation system in a way that emergency response personnel may (i.e. tear down stoppings to reduce airflow to the fire area) and see the effects in real-time.

Jan 1, 2012

By J. H. Fowler

Canada&apos;s gypsum industry began over two hundred years ago in the Maritime Provinces when farmers attempted to supplement their incomes by selling "land plaster" to traders bound for the United States. Rising from such humble beginnings, gypsum now contributes significantly to the economies of nine of Canada&apos;s ten provinces. Thirteen open-pit and three underground mines produced a total of 8.38 million tonnes of crude gypsum and seventeen processing plants manufactured 2.49 million tonnes of finished products in 1985. Recent economic growth in North America has resulted in steady increases in gypsum production, however, competition from foreign producers and by-product gypsum poses a growing threat to Canada&apos;s gypsum mining industry.

Jan 1, 1987

By K. N. Han

The kinetics of gold dissolution in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effects of stirring speed, temperature, oxygen partial pressure and lixiviant, concentrations on the overall leaching rate was investigated. It was found that the dissolution of gold could be represented by a heterogeneous chemical reaction. Under the conditions studied, the apparent activation energy ranged from 34.7 to 54.3 kJ/mol. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1998