Search Documents

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By William R. Yernberg

The combined 76th Annual Minnesota Section of SME meeting and 64th Annual University of Minnesota Mining Symposium were held April 8and 9, 2003, in Duluth, MN. This year’s theme was “Stakeholders, Partners in Change.” The meeting included four keynote speakers, technical presentations and a tradeshow. Engineers, executives, mining managers and suppliers from throughout the United States and eastern Canada attended the meeting. Reflecting the theme of the meeting, all agreed that the mine owners, the government, the community and the employees are all “stakeholders.” They must be “partners in change” for the iron ore mining industry to survive in the region. Compared with past meetings, where improved technology was the primary focus, this year the focus was on the dramatic restructuring of the entire industry. As noted by several of the speakers, “This time, the change is not in technology.”

Jan 1, 2003

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By David Baughman, Steven Axen, Ray V. Huff, Donald H. Davidson

Introduction In situ leaching (ISL) is an alternative method of mining uranium from deposits that are low-grade, deeplying, and water-saturated. ISL recovers uranium by transporting fluids through rock rather than by moving rock, a concept the Chinese developed over 2000 years ago for water production. This technique eventually evolved into production systems for oil, gas, sulfur, and salt. More recently, in situ methods have been developed to produce shale oil, gasified coal, geothermal energy, uranium, and copper. ISL uranium operations began in the early 1960s with Sabine Production Co. in south Texas. About the same time, Utah Construction and Mining Co. (Anderson and Richie, 1968) started similar operations in Wyoming's Shirley Basin. During the 1970s, six commercial operations were started in south Texas, (USBM, 1978) and a number of pilot operations were in various stages of development in Colorado, Wyoming, and New Mexico. This paper reviews some of the technical and economic aspects of the ISL process and briefly discusses key subsurface engineering functions as¬sociated with well pattern design and operation. While flow characteristics of a deposit are of prime importance, the following information is also needed: Depth, ore grade, total contained metal, ore thickness, flow conductivity (permeability), void space in rock (porosity), mineral type and distribution, natural groundwater flow, and structural features. Solvent selection, which is important to the economic success of the operation, takes these factors into account: Composition, rate of metal solubilization, interaction with gangue minerals, impact on rock permeability, impact on materials of construction, trace metal solubilization, cost, availability, and handling problems. Overview of ISL An ISL operation consists of these functions (Fig. 1): 1. Chemicals to dissolve and maintain uranium in solution are prepared at the surface extraction facility. 2. A set of injection wells forces the solvent into rock pores of fractures using pressure in excess of the deposit's hydrostatic pressure. 3. Solvent travels through the rock and reacts with uranium minerals to dissolve them. The solvent usually consists of an oxidant and a complexing agent in an acidic or alkaline medium. 4. A set of production wells creates a low-pressure sump where metal-enriched solution is collected for transport to the surface. 5. The enriched solution is processed to recover uranium and to separate the leaching solution for recycling through the system. The economic performance of an in situ operation may be estimated by integrating these related factors: (1) the flow rate of solution processed through the system, (2) rates of fluid injection and production from wells, (3) the rate of mineral solubilization in the liquid phase, and (4) the volume of rock swept by the fluid. As these factors reveal, ISL involves the technical disciplines of petroleum engineering, ore deposit geology, and hydrometallurgical processing. Wellfield Design Just as mineral engineers use drillhole information to plan a conventional mine, in situ engineers use similar information to design a well field. A thorough knowledge of deposit geology and reservoir properties is required. Early application of pressure transient testing, such as

Jan 2, 1980

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

Characterization of ore and waste-rock material using automated quantitative micro-mineralogical techniques (e.g., QEMSCAN® and MLA) has the potential to complement traditional acid-base accounting and humidity cell techniques when predicting acid generation and metal release. These characterization techniques, which most commonly are used for metallurgical, mineral-processing, and geometallurgical applications, can be broadly applied throughout the mine-life cycle to include numerous environmental applications. Critical insights into mineral liberation, mineral associations, particle size, particle texture, and mineralogical residence phase(s) of environmentally important elements can be used to anticipate potential environmental challenges. Resources spent on initial characterization result in lower uncertainties of potential environmental impacts and possible cost savings associated with remediation and closure. Examples illustrate mineralogical and textural characterization of fluvial tailings material from the upper Arkansas River in Colorado.

Feb 27, 2013

By Edward J. Cording, William H. Hansmire

INTRODUCTION The Washington Metro, a rapid transit system that will serve the District of Columbia, Virginia, and Maryland, has been under construction for about two years. Construction of the Metro by the Washington Metropolitan Area Transit Authority involves a large amount of cut and cover, soil tunnel, and rock tunnel construction. To aid initial construction and improve future designs, performance observations were undertaken on tunnels in the initial construction phase. The University of Illinois Department of Civil Engineering was engaged to carry out a comprehensive program of field observations and measurements for this purpose. One part of the program was on the first soft ground tunnel constructed in the system. The tunnel is a 2200-ft (670 m) twin-bore section, designated Contract A-2, in downtown Washington. Two objectives of this program were to determine the relationship of construction procedure to settlements and to observe the pattern of soil movement around the tunnel as an aid in evaluating underpinning criteria for nearby structures. A test section, consisting t three instrument lines located across the tunnel path, was established prior to mining in Lafayette Park to measure in detail both vertical and lateral soil displacements as the tunnel was mined through the section. The site was selected because it is free from surface structures and access for installation and reading of the instruments was convenient. Load and distortion measurements on the lining were also made within the test section; observations of construction procedure were maintained throughout construction.

Jan 1, 1997

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator's compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator's location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines' involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Robert S. Hendricks

LOCATION AND HISTORY The Lakeshore Copper property is located on the Papago Indian Reservation approximately 30 miles South of Casa Grande, Arizona. This major porphyry type deposit was discovered by El Paso Natural Gas Company in 1966. Following an extensive diamond drilling program, El Paso invited several mining companies, including Hecla, to examine the property with a view towards participation. Hecla's examination, and the attendant feasibility studies, led to agreements, which were finalized in September 1969, whereby Hecla would acquire a 50% interest in the property, and would act as operator. The Lakeshore deposit covers an area approximately 3,000 feet in width by 6,000 feet in length. It consists of an upper zone of disseminated copper oxides, averaging approximately 100' in thickness overlying a zone of disseminated copper sulfides up to 1,000 feet thick. Near the base of the disseminated ore is a blanket like zone of high grade copper sulfides, referred to as the tactite ore body. The mine is being developed to produce approximately 6,500 tons per day of oxide ore and 9,000 tons per day of sulfide ore. This represents a total daily production rate of 15,500 tons per day, which will be achieved by underground mining methods using rubbertired dieselpowered mining equipment. DEVELOPMENT LAYOUT The mine is being developed by two parallel 15° decline tunnels. The declines were collared 5,000 feet southeast of the ore body, and are being driven in a northwestery direction, to pass beneath the tactite ore zone. The declines will constitute the primary means of access to the underground workings. One decline (north

Jan 1, 1997

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009