Search Documents

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020

By H. Zhong, S. Wang, Q. Lin

To improve the flotation performance of chalcopyrite collector, 2-(tert-butoxy)ethyl xanthate (TBEX) and its derivative O-(2-(tert-butoxy)ethyl)-N-ethyl-thionocarbamate (TBEETC) were designed and prepared by the introduction of a 2-(tert-butoxy) ethyl group into xanthate and thionocarbamate. TBEX and TBEETC were both prepared via the one-pot method with superior efficiency, which has significant commercial implications. The micro-flotation tests demonstrated that compared with sodium isobutyl xanthate (SIBX) and O-isopropyl-N-ethyl-thionocarbamate (Z-200), TBEX and TBEETC both possessed better collecting ability and selectivity for chalcopyrite. DFT calculations and XPS were utilised to investigate the flotation mechanism involving TBEX or TBEETC and chalcopyrite. The results demonstrate that although 2-(tert-butoxy) ethyl group does not interact with minerals directly, its introduction reduces the energy of HOMO, so that they can better accept electrons instead of donating electrons which leads to better interaction with copper atoms rather than iron atoms. Keywords: Chalcopyrite, flotation, thionocarbamate, xanthate, synthesis

Jan 1, 2020

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By M. Nakamura, T. Akamatsu

Embankment dams are often constructed on soft rock foundations in Japan, so it is important to precisely predict deformation of the foundations due to fill placement at the design stage. In order to accurately evaluate the settlement and the strain of the rock foundation surface during construction, the influence of the scattering of the deformability of foundations on the deformation behaviour should be investigated. In this paper, a method of evaluating the settlement and the strain of the rock foundation surface during construction was studied with stochastic deformation analysis considering the scattering of the deformability of the dam foundation. Based on the analytical results, a dam foundation design using the deterministic method considering the scattering of its deformability was discussed. Da in Japan Uferdämme of auf weichen Felsfundamenten gebaut werden, ist es wichtig, die Verformung der Fundamente auf Grund der Platzierung der Aufschüttungen bereits in der Planungsphase genau vorherzusagen. Im Zusammenhang mit einer genauen Beurteilung der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten sollte auch der Einfluss der Streuung der Verformbarkeit der Fundamente auf das Verformverhalten untersucht werden. In der vorliegenden Studie wurde die Bewertungsmethode zur der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten mit Hilfe von Wahrscheinlichkeitsanalysen der Verformung unter besonderer Berücksichtigung der Streuung der Verformbarkeit der Dammfundamente untersucht. An Hand dieser analystischen Ergebnisse wurde das Design der Dammfundamente dann enthusiastisch mittels deterministischer Methoden hinsichtlich der Streuung der Verformbarkeit diskutiert. Comme les barrages en remblai sont souvent construits sur des fondations rocheuses tendres au Japon, il est essentiel de prévoir précisément les déformations des fondations causées par la mise en place du remblayage durant la phase de conception. Afin d’évaluer avec exactitude le tassement et la déformation de la surface du rocher de fondation durant la construction, l’effet de la dispersion de la déformabilité des fondations sur le comportement de déformation doit être étudié. Dans cette étude, l’auteur a étudié la méthode d’évaluation du tassement et de la déformation de la surface du rocher de fondation durant la construction en procédant à une analyse aléatoire/stochastique de la déformation et en prenant en considération la dispersion de la déformation des fondations du barrage. En se basant sur les résultats de l’analyse, la conception des fondations de barrage avec la méthode déterministe considérant la dispersion de sa déformabilité a été activement discutée.

Jan 1, 2003

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By George Kayesa

[ ] A multiple-bench slope failure occurred at Letlhakane mine on 14th July 2005. No injuries or damage to equipment was suffered and mining production was not affected. Slope failure was preceded by the precursors of tension crack formation, crack widening and extension as well as slope monitoring targets movement. It was predicted that slope failure was imminent using the Geomos slope monitoring system, though the timing was not certain. The area to be affected by the slope failure was also known before hand as was the slope failure mode. As a result, measures were taken to avoid exposing personnel and mining equipment to the slope failure risk. This paper discusses how the prediction of the slope failure of 14th July 2005 using the Geomos slope monitoring system resulted into avoiding potentially fatal injury, damage to mining equipment and loss of mining production.

Jan 1, 2006

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

By M. J. Sapko

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL's Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal's ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Jan 1, 2003

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

With the advent of the First World Conference on Sampling and Blending (WCSB1) in Denmark in 2003 and the subsequent biannual meetings, together with other sampling conferences held on a regular basis, the central tenets of sound sampling practice and theory are spreading throughout the minerals industry. End-users and project houses, or groups who execute the projects, are all now better-informed about the principles of ?correct? sampling and preparation. To support this, many large mining companies now have their own in-house champion who will advise and ensure that the supply of sampling equipment is correct in terms of design and application, which further contributes to improved metallurgical accounting. The presence of a sampling champion also ensures that consistent and acceptable standards in regard to sampling practice are maintained throughout the group. This has, in turn, placed a greater degree of responsibility on the shoulders of sampling equipment suppliers, in terms of their equipment designs and product offerings, as well as applications knowledge for effective installation of equipment on client plants. This paper attempts to highlight the significant challenges that sampling equipment manufacturers often face with regard to complying with the newly understood requirements of best practice and sampling equipment design. Manufacturers invariably face issues with end-users or project houses, including project cost control, restricted headroom for samplers in plant layouts, and a lack of knowledge in certain quarters. These all have a potentially negative effect on the final outcome of a proposed sampling solution or implemented project. In reality, what is intended by all parties and what is ultimately installed are at times very different, with undesirable consequences for all concerned. Against this challenging background, there are, however, a number of instances where intent and implementation are complementary, with very satisfactory results. Keywords sampling, mechanical samplers, design, installation, sampling theory.

Jan 1, 2014

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By S. C. Essack

"Tenova Pyromet has designed a slag flow control valve that throttles the flow of slag in order to control the tapping rate. In addition, the valve has proved to be a reliable tool for closing the furnace during normal operation as well as emergency conditions. The valve makes use of a water-cooled copper element that is hydraulically operated and attached directly to the slag tap-hole. The equipment is compact, simple to maintain, and cost-effective to purchase and install. It can be retrofitted to most existing slag tapholes with minimal modifications.During the development phase, finite element method (FEM) and computational fluid dynamics (CFD) software was extensively used to model predicted operating conditions and to optimize the design. By using CFD, it was possible to understand the flow patterns inside the copper and to optimize these to improve overall performance.The slag valve was installed and commissioned in 2011/2012 on a 12 MW furnace as part of a new mineral wool plant in the USA. It has performed well since its installation despite operating under conditions in excess of the original design criteria. During the first 6 months of operation it quickly became the preferred method of closing the furnace, although the design intent was for occasional use during emergency shutdown conditions only. Since replacing the mudgun as the main method of closing the tap-hole, a few minor changes have been made to the installation in order to cope with the increased heat load and much higher frequency of use."

Jan 1, 2014

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By P. T. L. Koh, M. P. Schwarz

A series of parametric studies were carried out for a flotation cell using computational fluid dynamic (CFD) modelling to determine the local response of hydrodynamic performance measures to change in operating conditions. As an example, an Outotec cell was used to carry out the response analysis. The hydrodynamics of the flotation cell has been previously investigated by laboratory measurements presented by Schwarz et al (2019), and a CFD model of the cell was developed and validated using these measurement data (Schwarz et al., 2019). In this work, parametric studies have been performed by modelling the flotation cell at different stirring speeds and gas flowrates, varying above and below standard conditions. Predictions of void fraction, bubble size, bubble surface area flux and particle–bubble collision rate are presented showing the effects of increasing and decreasing stirring speed and gas flowrate around the base case. Generally, the total gas holdup in the flotation cell was found to increase with increasing gas flowrate. The bubble diameter was found to decrease with increasing stirring speed and increase with increasing gas flowrate. The collision rate increased with both stirring speed and gas flowrate. The parametric results show that there is a correlation between the bubble surface area flux Sb which is affected by stirring speed and gas flowrate, and the particle–bubble collision rate. With the collision rate as an indication of flotation collection, it is also possible to show that cell performance can improve more by increasing stirring speed than by increasing gas flowrate in a situation where everything else remains constant. The CFD results can form the basis for a Response Surface Method (RSM) analysis which can then be used for automated optimization of cell performance. Keywords: Flotation kinetics, computational fluid dynamics, bubble surface area flux, particle-bubble collision rate

Jan 1, 2020

By E. Dervaric

The main purpose of this paper is to introduce the main strategic restructuring aspects of companies that are directly (coalmines) or indirectly (companies that depend on coalmines) linked to coalmining. An attempt is also made to determine the principal factors required for the successful execution of a restructuring process in companies focused on the basic activities of coalmining, such as companies that provide supporting activities. The restructuring process exerts an influence on the whole area that relies on coalmining. So coordination of activities among the government, the local community, and the coalmine is very important. This is the major premise of this paper. The first section of the paper focuses on identifying and analysing the key factors in restructuring and a selection of key methods, drawing on past and present practice. The key factors to be considered in a model of enterprise restructuring in the coalmining sector are considered. The second section is dedicated to the actual design of the model of enterprise restructuring in the coal industry. The proposed model is based on positive experiences in the restructuring of coalmining companies in Europe, with an emphasis on Slovenia, successful approaches to crisis management in corporations, and identifying key areas in bringing about a strategic turnarounds in company operation. To support the argument for the key business areas, a brief summary of empiric findings has been included to demonstrate the applicability of the proposed model and the restructuring process. The summary is based on the survey done in both Slovenian coalmining companies (especially in Velenje Coal Mine) and their subsidiaries. The conclusion integrates key findings and outlines issues for further consideration and discussion. Keywords: restructuring, coalmining, Velenje Coal Mine, strategic factors, restructuring model.

Jan 1, 2008

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017