Search Documents

By Edward J. Jr Walter, Edward J. Walter

The vibration problem is approximately fifty years old. The original investigation of the U.S. Bureau of Mines was begun in 1930. Significant investigation into the problem was done by Crandell, Langefors, et al, Edwards and Northwood, and again by the Bureau of Mines. This resulted in an effective Safe Limit standard expressed in particle velocity as 2.0 inches per second.

Jan 1, 1979

By Blenda Lopes, Rodolfo Matias, Vagner Paixão, Vinicius Leão VALE, Edivarde Sousa

Seismography is an extremely important subject in the context of rock blasting, especially in the current scenario, which involves the need for increased controls due to the growth of urban areas near open-pit mining operations. Worldwide, communities are becoming increasingly aware of the environmental and social impacts associated with mining activities. Therefore, maintaining good relationships with these stakeholders is essential to preserve the social license to operate and to comply with current legislation. This situation is exemplified in an open-pit iron mine near the capital of Minas Gerais, Brazil, where the community is located less than 40 meters from the pit boundaries. Blasting activities within the mining area occur at distances less than 500 meters from the nearest community, making continuous seismograph monitoring necessary to ensure that operational conditions are maintained without compromising exploitation efficiency. The threshold for peak particle velocity, according to Brazilian Standard 9653:2018 by ABNT, is 15 mm/s at frequencies around 4 Hz. However, even though the peak particle velocity commonly registered was inferior to 3 mm/s, there were still complaints from nearby residents regarding human discomfort. To further reduce vibration levels, a study was conducted to implement a new blast design, considering factors such as reducing bench height, altering the hole delays, maintaining the maximum charge per delay, and adjusting the drilling pattern without negatively affecting rock fragmentation quality. Following the implementation of the revised blasting parameters, seismographic measurements in the region decreased to below 0.6 mm/s. This significant reduction in ground vibrations contributed to minimizing community disturbances and fostering a more positive relationship between the company and its surrounding residents.

Jan 26, 2026

By Brent Coleman, Wade Hutchison

The Montgomery Bell Academy project is a parking garage structure topped by a soccer field. This project included expanding parking and moving the present tennis courts. The project is located adjacent to an affluent historic neighborhood that posed some special public relations challenges.

Jan 1, 2012

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By Keith L. Bockelman

The Colowyo mine is a unique surface coal mining operation because it is a multiple seam pit. Using a combination of a shovel-truck and dragline operation, Colowyo mines 8 seams of coal to a depth of 400 ft. Over the past 3 years a number of operational changes have occurred, one of which is the implementation of blast casting. Through this implementation Colowyo has been able to eliminate over one million cubic yards a year, which would have had to be removed by the shovel-truck operation. This has also brought about a significant decrease in the stripping cost per ton within the dragline operation.

Jan 1, 1985

By Franklin J. A, Tam C. Palangio, N H. Maerz

WipFrag systems I, II and III have become the world standard in photoanalysis systems to measure particle sizes. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved ~to allow automatic measurements of the size distribution of particles on moving conveyors, in truck boxesand on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can, be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes, which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1998

By Kevin Cole, Dennis A. Clark, F William Laslow

Since 1976, the Metropolitan Sanitary District of Greater Chicago, (MSDGC), has commissioned the excavation of a tunnel system in the Chicago area, hundreds of feet below the surface in solid limestone. This paper outlines the blasting patterns, explosive selections, and monitoring techniques used to assure a satisfactory job completion, following the specifications.

Jan 1, 1982

By David E. Siskind

U.S. Bureau of Mines Report of Investigation 8507 was published in 1980. In a comprehensive analysis of all known blast damage studies plus new definitive data, the USBM authors adopted new safe level criteria of 0.5 & 0.75 in/sec for the frequency range corresponding to structure resonances. These were 3 to 4 times lower than the existing limit of 2 in/sec and are the most restrictive scientifically-based blasting criteria for the prevention of threshold hairline cracks in homes. The Bureau's own tests involved 76 homes in six states. In USBM RI 8507, those tests were combined with data from nine other studies from the US, Canada, Czechoslovakia and Sweden in an overall conservative summary analysis intended to preclude blasting damage.

Jan 1, 1998

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By Leslie Taylor, Uli Leiste

In this paper, results from small scale testing conducted to determine pressure time profi les acting on a plate (taken to represent the bottom of a vehicle) at any given distance from the center of the plate will be presented. These results will be discussed in relation to visual observations of the upward moving sand.

Jan 1, 2008

By Steve Dillingham

The origin of the written blasting log or shot report can likely be traced back to the earliest annals of blasting and record keeping. These records were, for the most part, a way of checking inventory, production progress, or billing, and not necessarily designed with the intention of being used as a legal document in a court of law. As our litigious society has evolved to include far reaching regulatory requirements, however, the blasting log has developed to support and aid in the defense of the common blaster from blasting lawsuits by providing a comprehensive written report of his or her actions.

Jan 1, 2002

By Terri Jordan, Kenneth Hollingshead, Mary Jo Barkaszi

The Port of Miami, Miami-Dade County, Florida (Port) is the largest container port in the State of Florida. However, it is located in the center of a diverse ecosystem. Biscayne Bay surrounds the Port and portions of the bay have been designated as a National Park, a Florida Aquatic Preserve and a state Critical Wildlife Area. The bay is home to many protected, threatened and endangered species including the Florida manatee, five sea turtle species, American crocodile and bottlenose dolphin, in addition to important recreational and commercial fish species.

Jan 1, 2007

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By Peter Cameron, Tom BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle.

Jan 1, 2019

By M. Khaled, K. Abdel Rahman, M. Khattab

Helwan limestone quarry is located at a distance of 35 km (21.7 miles) to the south of Cairo downtown. Drilling and blasting operations are used to extract the limestone for the Helwan Cement Company (HCC). In 1980’s a new urban community was constructed adjacent to the quarry. This situation led to shifting of the old quarry 5.0 km (3.1 miles) to its current location, to avoid causing blasting problems to the new community. Unfortunately, the new quarry is opened in a highly faulted area, with weak zones of brittle materials. The drilling and blasting crew is facing many difficulties due to the geological complexity along these zones. Moreover, the extension of this community towards the new quarry makes the control of ground vibrations is very important.

Jan 1, 2008

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015