Search Documents

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985

By Conny Postnpaok, Mark E. Hammele

"A major problem that has continued to plague the surface oil industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through several years of field research in full-scale production environments. Many operations across the United States havebeen evaluated ."

Jan 1, 1989

By Wayne Rogers, Sarma Kanchibotla, Alan Tordoir, Bryon Bisiauz, Seth Ako, Eric Engmann

Blast induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered.

Jan 1, 2012

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Selwyn Pearton

Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades and through their unique properties offer significant advantages through improved safety, reliability and performance. Despite their advantageous properties, the benefits of pumpable emulsions have been unavailable to narrow reef mining operations due to the void in technology necessary for their successful implementation within the challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow reef environment.

Jan 1, 2015

By Dale Ross, Bill Clements, Jim Spanos

Current world conditions are forcing the search for "green" energy technology in every aspect of our daily lives. Finding alternatives to petroleum fuels seems to be at the top of the list. The search for the "perfect" alternative is something like the never ending quest of the perpetual motion machine. Unfortunately, the laws of physics prevent us from getting something for nothing, and Murphy's Law normally gives us nothing for a lot of something. Regardless of Murphy, the quest goes on, and in our industry cheaper ANFO seems to be the popular subject.

Jan 1, 2012

By Kirstin Girdner, Vicki Seppala, Tom BoBo, John Kemeny, Mike Higgins

Optimal blast fragmentation is fundamental to all phases of comminution. Changes in blast design may affect efficiency and productivity of downstream processes such as crushing, milling and leaching, resulting in cost savings or losses.

Jan 1, 1999

By Geff Gordon, Dale Nies

Small diameter borehole blasting can be very efficient and cost effective. As residential development continues to expand, many areas are now requiring blasting for site preparation and upgrading old utility systems or constructing new ones.

Jan 1, 1990

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Everett Clausen, Richard Walker

CIL/EVANinc and the Canadian Explosives Research Laboratory of the Government of Canada have evolved a concept developed by Research Energy of Ohio, into a landmine neutralization system that is the most innovative to date.

Jan 1, 1999

By M. L. Mendes, J. Q. Nojiri, S. C. Botelho, A. P. Campanha

In February 28, 2001 JOULE coordinated the first tests with an electronic detonator in South America at an iron ore operation - ITABIRA MINES from the Brazilian COMPANHIA VALE DO RIO DOCE (CVRD) - the largest producer and exporter of iron ore in the world. ITABIRA MINES (CAU and CONCEI O) belong to one of the complexes, called the Southern System, producing 56 million tons of ROM as well as concentrated products and pellets. This paper is going to describe the tests at ITABIRA MINES with results indicating the improvement in the excavator productivity and reduction of the mining global costs (due to the better performance of the equipment and potential reduction of the maintenance cost).

Jan 1, 2002

By Zoltan Susanszky

The total available energy in an explosive charge is seldom fully utilized in industrial operations. For this reason more explosive is normally used to perform a job than we would calculate. In an explosive detonation some energy is generated as waste energy which can not be efficiently used. This results in added expense and possible environmental damage. This waste energy can create problems in metal forming with explosives and during commercial underwater blasting operations.

Jan 1, 1976