Search Documents

By J. Drzymala, K. L. Wolters, T. Chmielewski, T. D. Wheelock, D. H. Birlingmair

Microflotation tests were conducted with a modified Hallimond tube equipped with a fritted glass disk and magnetic stirrer to determine whether the results would support an equation that predicts a linear relationship between particle size and the reciprocal of particle density in water for a specified flotation recovery in a given time. Data obtained with the tube for either hydrophilic or hydrophobic solids fit the equation satisfactorily. It was also shown that the natural flotability of molybdenite is somewhat less than that of elemental sulphur and that sodium dithionite is a good depressant for sulphurised pyrite. In addition, it was found that the untreated pyrite and galena used in the study were hydrophilic and did not float by particle-bubble attachment.

Jan 4, 1992

By S. K. Chaulya, R. S. Singh, B. B. Dhar

Two prominent local species, Dendrocalmus strictus (bamboo) and Saccharum spontaneum (kashi), and two exotic species, Cymbopogon citratus (lemon grass) and Vetiveria zizanoides (vetiver), were selected for growth trials on dumps at Mandaman, Chora, Mudidih, South Balanda and Ghugus. The climate at these sites is dry tropical and the surface soil layer a slightly acid to neutral sandy to clayey loam 10-11 cm thick, impoverished in major plant nutrients. After two years bamboo had grown the most, up to 325 cm in height, and contributed the greatest biomass, 638 g/m2 of plant. The local kashi species had a very good regenerative capacity, which was lacking in the lemon grass and vetiver. The grasses had very good soil-binding capacity and could also provide income if used as cash crops

Jun 21, 1905

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

Two of the most important economies in coal-washing are in the actual washing of the coal and in a proper lay-out to reduce to a minimum the cost of labour for handling and washing. A guarantee is usually required for turning out a washed coal containing not more than 2% of free dirt and a resulting refuse with not more than 2% of free coal; any plant that gives results within such guarantees can he considered economical, provided that there are no other losses during the washing process. Various drainage arrangements and washery lay-outs are illustrated and discussed with respect to drainage, bunkers, sieves, settling tanks and conveyors and two further points considered: siding accommodation, which may become quite important with washeries of large capacity especially when the coal is brought in railway-wagons; and the irregularity with which the coal arrives. (Paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair)

Dec 1, 1916

By M. Dobias, N. Mayor, J. Lillo, A. Gonzalez, R. Lunar, R. Oyarzun

The central domain of the Spanish Central System contains a series of Ba-(F)-(base metal sulphide) hydrothermal vein deposits that are hosted by adamellitic granitoids. Fluid inclusion and sulphur isotope data suggest that the mineralisation was formed by low-salinity hydrothermal solutions that incorporated fluids, metals and sulphur from a magmatic source. Mineralisation occurred in two main stages; a first stage of open-space filling with quartz-Ba-(F)-(base metals) ; and a second stage of brecciation and deposition of quartz-barite. The two mineralising events can be clearly related to two tectonic episodes of late Variscan age that involved extension along east-west trends followed by ductile transcurrent movements along northeast-southwest trends.

Jan 4, 1992

By Tawsaporn Nuchanong, Ian Nichol

Investigations of the dispersion of gold in soils and stream sediments associated with three gold deposits in Thailand indicate the existence of different geochemical dispersion patterns in the three areas, demonstrating the need for the adoption of a variety of exploration techniques. The three gold deposits which were investigated were the Phu Tham Phra-Phu Thong Daeng copper-gold prospect, the Doi Tung and the Huai Hin Lab gold prospects. Overall the investigations at the three localities demonstrate clearly that the chances of exploration success can be significantly enhanced if composite soil samples are analysed to ensure a more reliable estimation of the gold content in soils and if both the 63 micrometre fraction and the field-panned concentrates of stream sediments are analysed because of the variable grain size of the gold characterising different gold deposits and surface environments.

Jan 4, 1992

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By S. V. Shiraishi, H. B. Bell

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J. Cahalan, President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C120-C127, with a contribution by Wright P.A. on the miscibility gap

Dec 1, 1971

By R. E. T. Hill

"A laboratory study was undertaken to determine the condensed equilibrium phase relations at 600°C in that portion of the quaternary Fe-Ni-Cu-S system which lies in the neighbourhood of the monosulphide solid solution (MSS). The study sought to determine to w hat extent copper affects the temperatures of stability and compositions of iron-nickel sulphides in bulk compositions similar to those of massive Fe-Ni-Cu ores. Experimental data, including stable phase assemblages and phase compositions, are presented.In the quaternary system at 600°C MSS forms stable phase assemblages with pentlandite, chalcopyrite solid solution, pyrite and vaesite. Over the range of bulk compositions displayed by natural ores copper as well as metal/sulphur ratio have a significant effect on the thermal stability of pyrite and pentlandite. Errors therefore accompany the widespread practice of ignoring copper or chalcopyrite when the mineralogical and compositional changes that have accompanied the initial cooling of primary magmatic sulphides or their subsequent homogenization during isochemical metamorphism are being deciphered. These errors are most significant for ores the bulk compositions of which lie tow ard the sulphur-deficient side of the cupriferous MSS. Temperatures as much as 300°C above the copper-absent value are possible for the interpreted upper stability limits of pentlandite in these ores.The experimental data show that up to 2.0 at% copper can occur in pentlandite stable at 600°C in a bulk composition equivalent to natural magmatic ores. This is equivalent to nearly 10 vol% chalcopyrite. Pentlandite contains more copper than coexisting MSS and the copper content of both phases increases with increasing iron."

Jan 1, 1984

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

By L Casari

A study of samples from three sectors of the mine, which was worked from Roman times to 1991, revealed different textures, mineral associations and distributions of trace elements in the sulphides. In the last decade before closure, grades of sphalerite concentrate were in the range 51.67-53.30% Zn and 2.21-2.86% Pb and of galena concentrate 69.43-71.62% Pb and 4.70-8.36% Zn, while the estimated by-product germanium content of sphalerite concentrates sold was 300-400 g/t. Passing the different run-of-mine materials through the same concentrator flowsheet produced middlings and tailings during the preconcentration processing. Separate and alternative treatment of run-of-mine products would have yielded improved recoveries of sphalerite and galena and better values of by-product germanium and cadmium

Jun 18, 1905

By G Fakes

This paper describes the history of civil engineering tunnelling and developments in soft ground techniques during the 19th and 20th centuries, culminating in the design and use of high speed tunnelling machines for all types of ground conditions. Some of the problems encountered are outlined, and descriptions are given of some contemporary developments in rock tunnelling techniques, with comparisons of methods used in the mining industry.

Jan 5, 1996

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By K. El-Barawi, Hussein M. Kamal

Chlorination was performed of iron-rich chromite ore from Barramyia, United Arab Republic (UAR), together with its concentrate. The effects of change of grain size, chlorine gas flow rate, time and temperature were studied. The extent and mechanism of chlorination were followed through chemical and structural analyses of the feeds and complete chemical analysis of the chlorination products. By conducting the chlorination process for short periods at 600°C or lower temperatures, products having high Cr-Fe ratios suitable for ferrochrome production can be obtained.

Dec 1, 1971

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

By N T. Byrom

This paper is essentially in two parts. It describes how risk assessment fits into the overall framework of the activities required to control risk effectively within an occupational health and safety (OH&S) management system. It then goes on to describe the assessment of an OH&S system by the process of auditing.

Jan 7, 1996

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991