Search Documents

By Ranjeet K. Singh

Kelsey Centrifugal Jig was found to be promising for the beneficiation of fine coal particles. The present study was aimed at in-depth understanding of the separation features of Kelsey Jig through detailed experimentation. Beneficiation of fine coal of size 150 x 300 µm was studied in a laboratory Kelsey Jig. The thickness of the ragging bed is found to be an extremely crucial parameter apart from the other process parameters such as rotational speed and pulsation frequency. A constant pulp density (25% solids) of the feed slurry was maintained in the study. The feed rate was also kept constant at 50 kg/hr dry solids. Silica sand of size -1.68+0.85 mm was used as ragging material to avoid the pegging of internal screen having an opening of 425 µm. The rotational speed was found to have significant effect on the depth of the ragging bed and its porosity, which influenced the separation performance considerably. Pulsation was identified as the key factor in stratifying the coal bed and defining the misplacement as well as ragging bed porosity, which influenced the mass yield and quality of the products. Beneficiation studies were carried out with rotational speed varying between 900-1000 rpm while pulsation frequency was kept within 850-925 rpm. In a single pass through the Kelsey Jig 7-8% (absolute) reduction in the ash content of the feed material was observed at more than 55% mass yield. High rotational speed, moderate pulsation, and low ragging bed depth favored good cleaning. A high bed depth was found to facilitate rejection of high ash materials. It was established that Kelsey Jig is effective in fine coal cleaning though a controlled operation is required in order to achieve superior performance. Keywords: enhanced gravity separator, g-force, separation performance, ragging material, coal beneficiation

Sep 1, 2012

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By P. K. Arya

Huge quantity of copper is lost in Crown, Sill, Rib Pillars, hanging wall, foot wall and unexploited ore bodies in several closed underground copper mines and old worked out stopes of Hindustan Copper Limited at Mosaboni and other places. These mines might have been uneconomical to work with conventional mining methods. However, huge quantity of mineral reserves is lost due to their closure. Chemical and in-situ bio-wash leaching, if tried can provide an answer to facilitate the recovery of metallic values economically. Encouraging results were obtained during an experiment at North Badia Mines at Mosabani in the past. Though the experiments were not completed but whatever results obtained were very encouraging and can be successfully tried to make it viable. The results of the experiments are discussed here and a plan is suggested to recover copper from such mines.

Jan 1, 2014

Cenospheres is a sandlike hollow sphere component of the fly ash that is collected in coal-burning electric power generating plants. Metal coated particles have been widely used in industries. Magnetron sputtering method which was used to coat copper film on the surface of the cenospheres is a widely used coating technique in large surface metal coating. A newly designed equipment is used to make the fine particle coating can be carried out because the fine particle is hard to disperse and it must make the particle keep moving to let every direction of the particle be coated. The copper film coated is compact, smooth, even and without uncoated spots under the optical microscopy and SEM. The film has good affinity to the cenosphere surface. The film does not separate with cenoshpere surface even when the cenosphere is crushed. The XRD, SEM, XPS, SPM was used to study the copper film characteristic. It is shown that using this newly designed magnetic sputtering equipment can coat high quality copper nanofilm on the cenoshpere surface.

Jan 1, 2014

By G. M. Savov

Copper recovery via Solvent Extraction (SX) process is a well-known technique, which is practiced commercially for approximately 40 years. The main advantages of the SX process are: an absence of using high temperatures (not more than 50oC), complete recycling of barren solutions, very high selectivity at removal and purification of metals, metal conversion to a form, suitable for easy subsequent recovery. Despite the wide acceptance of Solvent Extraction, it does have some shortcomings, namely SX employs large quantities of volatile organic substances. This leads to huge plant ?footprint? of SX circuits. The SX is very sensitive to low temperatures and quantity of total suspended solids in feed solutions and this causes bad phase disengagement times and therefore poor process performance. And most important ? low grade solutions (with copper concentrations below 1 gram per litre) are very unattractive for treatment via Solvent Extraction process, because capital costs for SX plants are not a direct function of copper tenor in the feed. The combined process with Ion Exchange (IX) and Solvent Extraction ? further called IX/SX by IONTECH Engineering was developed. This combination eliminates SX negative characteristics shown above. The key findings of the IX/SX process are; (1) recovery of copper from pregnant leach solutions with metal concentrations, varying on a broad range; (2) can be operate effectively with very low-graded copper pregnant leach solutions; (3) the construction of large ponds for pre-filtration of the pregnant leach solutions is not necessary; (4) working with turbid solutions and solutions containing large quantities of suspended solids; (5) winter operation without troubles; (6) strongly reduces organic losses; (7) technological approach lead to plant sizes reducing. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality.

Sep 1, 2012

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By G. K. Palshikar

Mining operations offer many opportunities for the use of IT and communication technologies to improve automation and thereby deliver higher levels of productivity, cost, quality and safety. In this paper, we discuss a particular application, namely, building a fully automated train control and operation system within a mining area. We first outline the basic architecture and functionality of such a system and then present a real-life case study where the railway system within a remote iron ore mine in Canada was converted to a fully automated train operation system. This hard real-time safety-critical system required the use of advanced technologies such as embedded systems (e.g., on-board train controller), radio communications, formal methods, optimal scheduling, and extensive simulations. We focus on the design aspects for maintaining the system in safe states.

Sep 1, 2012

By P. K. Fedotov

At projecting mining-concentrating complex at the deposit ?Zapadnoye? (Russia) it was considered to enable an opportunity of refusal from conventional SAG-mills. First time a scheme of gold bearing ore destruction using Roller Press RP 5-100/90 had been developed and integrated. The plant was launched in summer 2003 and presently it has achieved designed technological parameters, processing throughput comes to 1 million tons of the ore per year.

Jan 1, 2014

By Rajamani R. K.

The design of tumbling mills has progressed from the Bond work index concept of the 1950s to the population balance concept of the 1980s and then made a quantum leap forward with the discrete element method in the 1990s. The failure of a SAG mill at the Grasberg mine site set in motion the inquiry into the role of shell lifter geometry on the profile of the charge motion within the mill. Quickly, it became evident that this could only be accomplished by tracking individual motion of ore particles and grinding balls and not by study of en masse motion of the charge that had been established previously. The discrete element method (DEM) which was prevalent in the civil engineering literature at that time proved suitable to tackle this simulation problem. In 1991, the two dimensional simulation of laboratory scale mills was validated with the DEM. Later this simulation method evolved into ?MillSoft?? a simulation software package for the design of lifters in ball and SAG mills. MillSoft?simulations proved that cataracting charge motion is not conducive to the life of lifters. The old rule of thumb that the number of shell lifter rows should equal twice the diameter of mill in feet was shattered by simulation results. Instead, the number of rows equal to the diameter of the mill in feet, providing that the lead angle of lifter is around 25 degrees, was established as being more optimal. This bold design change was first implemented and tested by Mark Sherman at Alumbrera Mines in Argentina. Two 36-ft SAG mills responded extremely positively to the design change. This success was immediately repeated at Collahuasi, Pelambres and other mines in South America. The design change has so far exceeded expectation that there is not a single SAG mill around the world today that does not employ a relief angle on its shell lifter. The DEM method has advanced in the hands of the author, mining companies and universities, notably in Australia and South Africa. Today, three-dimensional simulation of charge profile and slurry transport is a standard in the design of mills. There is strong pursuit of a virtual comminution machine with DEM in Australia. In South Africa, an experimental method known as positron emission tracking is emerging as a method for tracking particles in grinding mills. The computational burden of computing with millions of particles in three-dimensional simulations has been eased to less than a day with a technique known as GPU computing. Keywords: DEM method, GPU computing, SAG mill, tumbling mill simulation, discrete element method

Sep 1, 2012

By L. K. Smith

Flotation work conducted by CSIRO on both single minerals and high-arsenic copper ores from a number of sources, has shown it is possible to produce separate low-arsenic copper concentrates and high-arsenic copper concentrates from high-arsenic copper ores. The procedure involves controlled separations at high or low pulp potential regions exploiting subtle differences in the flotation behavior of the arsenic-bearing and non-arsenic-bearing copper minerals. An overview of several case studies investigating the applicability of the controlled potential flotation approach to the separation of copper and arsenic from sulfide copper ores is presented. It highlights the variables which influence the efficiency of the separation which include mineralogy, liberation and reagent selection. The procedure can produce a saleable low-arsenic copper concentrate, which can be directly smelted without penalty, and a high-arsenic low copper concentrate, which will require further processing. Keywords: flotation, copper, arsenic, controlled-potential flotation

Sep 1, 2012

By S. K. Chaurasiya

o meet the ever increasing demand of iron oxide feed stock for rapidly growing domestic steel industries and to effectively manage the depleting reserve of high grade lumpy iron ore, Pelletization of iron ore fines/slimes are expected to play a dominant role in the near future. Use of pellets will also enable the blast furnace operator to achieve higher levels of productivity with lowering of operating cost. The effective utilization of Iron Ore Slimes is important not only from the point of view of optimum utilization of Iron values in the mined ore but also for preventing environmental pollution. A significant amount of slime is being accumulated at the tailing dam of one of the iron ore mines and with the present scale of operation the tailing dam will be filled in another 10 years. Hence to increase the life of tailing dam and for better utilization of the iron values a study has been carried out for the suitability of pellet manufacturing with slimes and fines at our laboratory. The pelletization studies are aimed for optimization of various parameters for production of Blast furnace/ DR grade pellets from beneficiated slimes and Fines. This paper attempts to describe the production of blast furnace grade pellets from beneficiated slime and fines and its characterizations.

Sep 1, 2012

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By V. K. Gupta

Selection of mill size for reducing a feed material of a given size to the desired product size is generally based on the specific energy estimate obtained from Bond test. Over the last thirty years or so, an attempt has been made to develop a more accurate and powerful alternative approach based on the characterization of the particle breakage kinetics and material transport through the mill over a range of operating conditions of interest and correlating the degree of size reduction achieved with the net specific energy input to the mill. Particle breakage kinetics are described in terms of the specific grinding rate and breakage distribution parameters for the individual size fractions. Precise estimates of these parameters and the net energy input to the test ball mill (a laboratory or pilot scale mill) are important for development of desired energy-size correlations. In this context, three tasks are important: (a) preparation of the feed charge, (b) design of batch grinding experiments and (c) computational technique used for estimation of the breakage rate and breakage distribution parameters. This paper highlights several aspects of these three tasks that have been overlooked by researchers working in this field, and describes a more appropriate approach for estimation of model parameters and specific energy input. Several examples are included based on the data available in the literature and those generated in our laboratories to illustrate important points.

Sep 1, 2012

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014

This study examines the surface alteration and flotation behaviour of synthetic moncheite, PtPd(BiTe)2, in the presence of pentlandite. The telluride minerals contribute around 20% ~ 30% and up to 45% of the PGM present in the Platreef ore and are considered to be slow floating as there is evidence of these minerals reporting to the tailings. It was proposed that oxidation products from other minerals and grinding media would affect the mineral surface composition and floatability thereby causing inadvertent depression of moncheite due to precipitating ions. ToF-SIMS analyses (time of flight secondary ion mass spectrometry) was used to characterise the mineral surface as well as the extent of surface alteration. Microflotation was used to deter-mine the hydrophobicity of the synthetic minerals. Conditioning of moncheite in the presence of pentlandite reduced the flotation response of the + 38 -106µm size fraction from > 99% to 56%. This was due to pentlandite dissolution products (iron and nickel hydroxy species) which formed overlayers on the mineral surfaces thereby inhibiting the adsorption of collector. In addition, further grinding of these samples, with and without pentlandite conditioning showed a negative effect on recovery due to the fineness of the particle size distribution and there was no advantage gained from any possible exposure of fresh sites in the sample.

Jan 1, 2014