Search Documents

By J. J. Cai

The status of fossil fuel and secondary resource in metallurgy industry in China were reviewed, and conversion efficiency of fossil fuel, utilization technologies of secondary energy were studied. Fossil fuel, accounting for over 90% of energy structure in metallurgy industry, took in the highest flight in China, and a great deal of which was converted to secondary energy through the equipment of blast furnace and coke oven. These secondary energy which were mostly made of blast furnace gas(BFG), coke oven gas(COG) and Lindz Donawitz gas(LDG) occupied about 30% of total secondary energy. The way enhancing fossil fuel conversion efficiency, secondary resource recovery and the secondary energy such as BFG, COG, LDG utilization promoted to save fossil fuel was discussed in this paper. And efficient use of lower caloric value fuel was studied, such as preheating combustion air and fuel, generating electricity power etc. and regeneration purposes of high-caloric fuel was also researched, for producing hydrogen, methanol or direct reduction iron etc. The using model of secondary energy at iron and steel works was presented as fuel and chemical materials. The results suggest that utilization of these energy efficiently and reasonably could help to energy saving and environment protecting.

Jan 1, 2014

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By Xiaoping Xu

An albitization granite type tantalum-niobium ore from Jiangxi Province, China was taken as the research object in this paper. The main valuable minerals in this ore are tantalite-columbite and uranmicrolite, and the minerals that can be comprehensively recovered include cassiterite, sulfide minerals, topaz, zinnwaldite, and quartz-feldspar. Based on the research results of process mineralogy, the roughing process of gravity separation for coarse particles combined with flotation for fine particles is proposed. The combined cleaning process of flotation-gravity-magnetic-electric-hydrometallurgical separation is adopted for the rough concentrate of gravity separation while the combined cleaning process of gravity-flotation- hydrometallurgical separation is adopted for the rough concentrate of flotation. High intensity magnetic separation is used to separate and recover zinnwaldite and quartz-feldspar from gravity tailings. By mineral processing for the crude ore containing (TaNb)cassiterite concentrate is 0.0003% with a grade of Sn 63.22% and a recovery of Sn 47.42% while the yield of sulfide concentrate is 0.0783% with a grade of Pb 33.15% and Zn 27.09% which can be separated to get lead and zinc concentrate respectively. The yield of topaz concentrate is 0.1545% and the topaz mainly distributed in the size range of -0.4+0.074mm, which can be made into abrasive products of different particle sizes after classification. The yield of zinnwaldite concentrate is 16.91% with a grade of Liwhiteness of 75%, which is a glass-ceramic material of good quality. 2O5 0.0346%, Sn 0.04%, Pb 0.10% and Zn 0.33%, the tantalum-niobium concentrate with a yield of 0.00278%,a grade of (TaNb)2O5 53.61% and a recovery of (TaNb)2O5 44.49% is obtained. And the yield of 2O 1.34% and Rb2O 0.40%. The yield of quartz-feldspar concentrate is 30.42% with a grade of K2O+Na2O 8.98% and Fe2O3 0.11% and a natural All of tantalum, niobium, cassiterite, topaz, zinnwaldite, quartz, and feldspar are recovered effectively. Keywords: tantalum-niobium ore, gravity separation for coarse particles, flotation for fine particles, comprehensive recovery

Sep 1, 2012

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Imre Gombköto, Zoltán Pap, Ákos Debreczeni, Sándor Nagy

Eddy current separators have become generally used in waste recycling industry during the last decade. There are many papers dealing with separation processes on eddy current separators, and also many article describes particle trajectory and different particle features affecting particle trajectory. These data are used in modeling as well. Within the frame of R&D project called ‚Fundamental research into the exploitation of the economic development potentials of critical raw materials in international co-operation - CriticEl?, authors are aimed for using Eddy Current Separator (ECS) as a mechanical separation step of high value critical elements recovery of selected WEEE’s like display panels, PCB’s. ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor is used for experiments targeted development of methodology for determining separability of different particles on ECS. The subject of our work was to investigate the behavior of model particles with different shape, conductivity (aluminum and copper), orientation and size in order to separate Al and Cu according to the results of many experiments were carried out in this field. However it looks like that throwing distance of one particle is only possible to describe by a certain distribution for even the same particle within the frame of the same conditions. Sample mean and standard deviation are depending on some of the particle feature and acting forces. The paper is going to draft the first results on the relationship between distribution of throwing distance and particle properties.

Jan 1, 2014

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By F. J. Sotiuo

Variability of the quality of phosphate ore feed to the flotation plant has been of great concern for the industry. This variability sometimes resulted in 10% to 50% decrease of P2O5 recovery, a reduction of P2O5 concentrate grade and/or both due to depression of the system. For this investigation, samples of refractory ore and easy-to-float ore were obtained from the same mining area in Central Florida; and then submitted to bench flotation tests using fatty acids (FA). To understand the cause of difference in flotation behavior of these apparently similar ores (grade, mineralogy, and physical appearance), bulk and surface characterization studies were conducted. Based on the results of characterization studies and bench flotation tests on both refractory and easy-to-float samples, it was possible to determine FA surface coverage. It was found that the surface coverage for the refractory ore was between 6.9% and 9.8%, corresponding to 0% and 80% recovery, respectively; whereas the easy-to-float ore showed surface coverage of 17.2% (89% recovery) to 24.6% (98% recovery). Since size analysis, surface area and pore size measurements showed small differences, it was thought that the surface coverage differences could be caused by the ad-sorption of natural compounds onto the phosphate ore surfaces, depressing the system. SEM, EDS, and Leaching and Solvent Extraction (LSX) studies were performed on the phosphate ores to demonstrate the proposed mechanism. This paper summarized our characterization studies, flotation results, and findings. The study showed that the new identified compounds were responsible for the flotation behaviors of the Florida refractory phosphate ores.

Jan 1, 2014

By P. S. Dash

With implementation of stringent environmental regulations, ultra clean coal technology development programs have gained significant importance worldwide. As far as Indian scenario is concerned, most of the coals present in India are of drift origin and low grade, containing high mineral matter varying from 15% to greater than 50%. The inorganic or ash constituents of Indian coals are finely disseminated through the organic or carbonaceous constituents so, that commonly used physical beneficiation techniques are of only limited value in affecting separation. Chemical processes involve addition of chemicals, which react with the mineral matter and allow its easy removal. The present study envisages the effect of aqueous alkali leaching followed by acid washing on the removal of mineral matter from two different captive coals of Tata Steel at elevated temperature and pressure. The experiments are conducted at desired conditions using a bench scale pressure reactor set up having proper data acquisition and control system. The research study revealed, that it is possible to reduce the ash content up to 70% by this method. The alkali content of the product clean coal does not increase whereas the silica and alumina content reduces by nearly 58% and 62% respectively. Significant reduction in the phosphorus content is observed after the acid treatment. The crucible swelling number of the feed coal improves after the treatment. The mechanism of demineralisation was evaluated by analyzing the coal samples before and after the alkali and acid treatment using scanning electron microscope (SEM). Because of the acidic nature of the silicates and aluminates, they dissolve into the NaOH solution and form sodalite. Sodalite is partially soluble in the alkali solution. The hydrates formed during alkali treatment are partially removed due to acid wash. This study in overall provides an insight into possible alternative methods of beneficiation for removal of ash from high ash Indian coals.

Sep 1, 2012

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By G. G. Dong

This paper presents BF flotation machines in brief which are manufactured by Beijing General Research Institute of Mining & Metallurgy (BGRIMM). Dimensional analysis and similarity criteria have been used to scale up BF flotation machines. These scale-up criteria can be used to determine mechanical structure and hydrodynamic parameters including mixing, solids suspension, air transfer and power and so on. Similarity criteria are used to design 40m3 flotation machine being based on data from 1.2 m3 to 20 m3 flotation machines. Hydrodynamic tests of 40 m3 flotation machine in water are discussed.

Jan 1, 2014

By Z. G. Guan

The tungsten ore in Xingluokeng belongs to a symbiotic deposit containing granite and fine vein-type wolframite and scheelite. The tungsten (WO3wolframite) accounts for only 0.233% of the raw ore, 49.60% of the , 49.60% of the scheelite and 0.8% of the tungstite. The dissemination size of the tungsten ore is extremely uneven, with 0.02~1.28 mm for scheelite and 0.01~1.28 mm for wolframite. The dissemination size of scheelite is coarser than that of wolframite. The size of 83% of scheelite and 60% of wolframite is greater than 0.04 mm. The composition of minerals in the ore is quite complex. The major metallic minerals include wolframite, scheelite and pyrite, which are followed by molybdenite, chalcopyrite, arsenopyrite, limonite, magnetite, hematite and siderite. The major gangue minerals include quartz, feldspar, muscovite, biotite and sericite, which are followed by chlorite, fluorite, apatite, dolomite, etc. According to the dissemination features and liberation degree of the tungsten minerals, the technology flowsheet of gravity concentration for coarse particles and flotation for fine particles to re-cover the low-grade and fine vein-type tungsten minerals is adopted, and -0.7 mm is selected as the processing size. The closed-circuit grinding procedure, with the combination of the rod mill and high-frequency vibration screen, is adopted. The grinding product is classified into three products of -0.7 +0.2 mm, -0.2 +0.04 mm and -0.04 mm. The gravity separation is adopted for the former two to recover tungsten minerals and the flotation is adopted for the last one. Under the condition that the raw ore contains 0.23% WO3, some technology indexes of beneficiation have been achieved. The gravity tungsten concentrate contains 63.54% WO3 with the recovery 70.11%. The slime flotation tungsten concentrate contains 35.22% WO3 with the recovery 10.48%. The composite tungsten concentrate contains 57.53% WO3 with the recovery 80.59%. Thus, the tungsten minerals are re-covered effectively.

Jan 1, 2014

By P. Vijay Kumar

Phosphate minerals are conventionally concentrated by flotation process using soap or soap- light diesel oil emulsion as collector. Some plants use detergents such as sodium petroleum sulfonate or alfa olefin sulfonate to enhance efficiency of soap flotation. It is reported that urea a known hydrotrope enhances flotation efficiency of soap as efficiently as alfa olefin sulfonate or linear alkyl benzene sulfonate at bench scale tests. In the present study tri sodium citrate also a known hydrotrope is tested as promoter in the flotation of phosphate mineral from Eshidiya ore.

Sep 1, 2012

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By M. V. Sowmya

Batch biosorption experiments were carried out for the bio-remediation of Cr (VI) ions from aqueous solutions using Serratia marcescens, a Gram negative, heterotroph and Gram positive bacterial isolates from a chromite mine. The influence of various experimental parameters such as contact time, pH, concentration of Cr (VI) ions and amount of biomass was evaluated with respect to the uptake of Cr (VI). The bio-sorption of Cr (VI) was found to be quite rapid and the percentage biosortion was found to increase with increase in the equilibrium chromium concentration. The free energy of biosorption of Cr (VI) was estimated to be in the range of -23 to -25 kJ/mol for the chosen bacteria. The uptake of chromium by the bacteria was confirmed by EDX and FTIR spectroscopy. As a follow up of this study, bacterial strains resistant to hexavalent chromium were isolated from a chromite mine in Karnataka, India and identified as Arthrobacter sp., Micrococcus sp. and Exiguobacterium sp. using 16s rRNA sequencing. The efficacy of the bacterial isolates for Cr (VI) uptake was assessed and over 90% bioremoval could be achieved for Serratia marcescens and Micrococcus sp. isolate. Possible mechanisms of chromium uptake by the microorganism are discussed. Keywords: bioremediation, hexavalent chromium, biosorption, bioreduction

Sep 1, 2012

By Z. S. Abisheva

Results of the study targeted to development of universal acidic-extraction-precipitation technology for gallium recovery from the sublimates are presented in the paper. This will let to utilize a new non-traditional source for gallium production. Phase composition of gallium containing dust was studied. Forms of gallium in the sublimates were determined. The main form is Ga2O3, however, GaP form is also present in the cottrel dust and Na5Ga3F14 form is present in the dust of aluminum electrolysis. The possibility of gallium concentration was established via secondary pyro-selection of the dust. Kinetics of interaction of dust components with sulfuric acid was studied. The products of the interaction subsequently were leached with water. Optimum conditions for direct leaching with HCl and H2SO4 were determined providing gallium recovery from the cottrel dust and the ash carry outs up to 95 %. Gallium recovery from the primary dust and the secondary dust of aluminum electrolysis was at 52; 64 % and 63; 83 % respectively. Effect of Fe, P, K, Na and Al admixtures for gallium extraction from hydrochloric acid solutions was studied. It was shown that gallium chloride complex (GaCl4-) is extracted into the organic phase from the following acid mixtures: HCl + H2SO4, HCl + H3PO4, HCl + H2SO4 + H3PO4, HCl + HF. Kinetic regularities of gallium extraction in the system (tri butyl phosphate) TBP ? HCl - Ga were studied using diffusion cell method with agitation. Optimum conditions for gallium extraction from complex hydrochloric acid solutions with TBP were found providing 99.9 % recovery and separation coefficient for gallium and iron (III) of more than 25 in one stage. Sodium hydroxide and water were selected as reagents for re-extraction of gallium from the organic phase. Different options for disposal of by-products that are formed in the processing of cottrel dust, ash sublimates and dust of aluminum electrolysis were proposed and tested. Keywords: gallium, kinetic, sulfatization, leaching, extraction, technology

Sep 1, 2012

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018