Search Documents

By Heribert F. Broicher, Arne Volland

"The analysis of laser-induced fluorescence (LIF) combines remote sensing techniques with laser spectroscopy. Over variable distances different rock types are identified or changes in the quality of one rock type are recognised. LIF Analysers operate non-destructive, non-contact, on-line and in real-time. Installed over conveyors or over driveways the analysers ""look"" at the moving bulk solids 20 times per second and provide in real-time information for downstream sorting, blending or optimisation of processing. LIF Analysers recognise rock types (hardness information or dilution control), degrees of alteration, degrees of oxidation and –semi-quantitative- content of certain minerals in an ore. Only under favourable conditions quantitative assay information can be obtained, as e.g. the phosphorus content of Kiruna type iron ore.The main application of LIF Analysers is seen in big open pit operations, where the muck is trucked to an in-pit crusher and the crushed rock conveyed out of the pit to its respective destination: e.g. the primary high grade ore to the mill, the low grade or oxidised ore to the leach pads and the internal waste to the dumps.In underground mining and especially in block caving operations dilution control is of utmost importance. Here a LIF Analyser mounted on the back of a pick-up truck can be moved from drawpoint to drawpoint and quickly assess the degree of dilution.Closer to the mill the stockpile management based on LIF analysis will lead to stockpiles sorted according to rock type (hardness), degrees of alteration and oxidation. In case of direct feeding rom ore to the mill the knowledge of the type and quality of all the material between the in-pit crusher and the mill facilitates optimisation of e.g. reagent dosage."

Jan 1, 2003

"The effect of operational conditions, such as air flow rate, impeller speed and solid concentration, as well as the effect of solids concentration and frother dosage, on the bubble size distribution produced in a lab scale flotation cell, were investigated. The cell was operated under batch conditions. The measurement of bubble size was accomplished using an automated photographic technique. The technique enabled fine and coarse bubble distributions to be measured in two-phase (liquid-gas) and three-phase systems (solid-liquid-gas). In each experiment, around ten thousand bubbles were characterized.This paper discusses the main results obtained using the new photographic technique and compares these with previous findings available in the literature. The results indicate that photographic techniques combined with digital imaging processing might become a standard technique for measuring bubble size distribution in flotation machines.HUT BUBBLE SIZE ANALYSERThe importance of having precise and reliable equipment for measuring bubble size distribution in industrial flotation machines has been widely recognized. The measurement of bubble size, particularly in three-phase systems, is rather complex due to the opaque nature of the pulp. However photographic techniques combined with ingenious sampling techniques are utilized for overcoming this difficulty. The technique named HUT, combines previously developed visualization methods with digital image processing procedures. In this technique bubbles and aggregates are exposed to a monochrome progressive scan camera. The acquired images are directly stored in a computer connected to the camera for post-processing. The sampling apparatus consists essentially of a vertical tube for collecting bubbles, a viewing chamber and a collection chamber, where particles carried by the bubbles are released. The function of the collection chamber is to maintain the viewing chamber clear for imaging purposes. Each image is automatically processed off-line, using digital image tools. In this paper the advantages and limitations of this new technique are described."

Jan 1, 2003

By A-M Ahonen

The paper discusses the experiences of a fast-track curriculum designed to provide the industry with engineers capable of working in minerals processing industry. The course has been done once before and the second course has been started. Students chosen have graduated from other fields of engineering. For the first course, twelve students were chosen from 152 applicants and for the second the twelve students were chosen from 96 applicants. The basic idea of the curriculum is to alternate between theoretical studies at the university and working experience periods at industrial sites. In addition, there are several one week assignment tasks at industrial sites. The theoretical periods are six to eight weeks long and there are three of them. During the first period, the teaching concentrates on unit processes and their chemical and physical background. The theme of the second period is mineral engineering systems; flowsheet development, process dynamics, control systems etc. The last theoretical period teaches environmental issues, leadership, project work and other similar topics. Each of the theoretical periods ends with an assignment week at industrial sites. The assignments are designed to wrap up the teachings of the period. For the industrial periods, the students are given learning goals, which have been discussed and designed with their industrial mentors. They are required to find relevant literature, make experimental designs, implement those designs, present the data, and make conclusions of their results. During these periods, a weekly meeting over the Internet is compulsory. Keywords: mineral processing, flowsheet development, process dynamics, control systems, constructivism, zone of maximal development, Vygotsky

Sep 1, 2012

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By Gábor Mucsi, József Faitli, Imre Gombköto, Sanjay Kumar, Zoltán Molnár, Balázs Ráczkevi, Ádám Rácz

"Generally, fly ash particles are very fine (< 100 ?m), mainly spherical and glassy materials form an outer shell on it. This paper deals with the laboratory investigation of ground fly ash based geopolymer. This material can be applied in many fields, mainly in the construction industry, e.g. non-structural elements, concrete, pavements and products, containment and immobilization of toxic, hazardous and radioactive wastes, advanced structural tooling and refractory ceramics, and fire resistant composites used in buildings, etc. The preparation of fly ash using high energy density milling is presented. Systematic experimental series were carried out in order to optimize the preparation process. The particle size distribution (LPSA) and structure of fly ash (FTIR) and the uniaxial compressive strength ,the permeability and structure of geopolymer product, furthermore the rheology of geopolymer paste were investigated. The product properties were studied as a function of the fly ash fineness. As a result of the investigation the relationship between the grinding circumstances, the ground material properties and the geopolymer characteristics was identified. It was found that the above mentioned physical properties of the geopolymer strongly depend on the grinding process."

Jan 1, 2014

By Kyle P. Flynn, Frank J. Hrach, James D. Bittner

ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1µm) to moderately coarse (300µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.

Jan 1, 2014

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By Valery V. Kostjuk, Victor. N. Bredikhin, Alexander I. Shevelev, Evgeny A. Kazban

"The investigations to improve the process data have been done in order to stabilize the functioning of drying units. The scheme of turnings preparation with centrifuging and subsequent thermal degreasing (tandem) is proposed. To improve the efficiency of the process the scheme of reclamation of the centrifuge fugate is developed with production of oil and service circulating water. Empirical dependences of the turnings temperature influence on the lubricant-coolants content in centrifuging are gained. When the turnings temperature is increased to 80 C the residual content of LC is decreased by 1.5%. The investigations aimed to improve the preparation of non-ferrous turnings have allowed to decrease the melting loss by 15-20%; to stabilize the process of thermal drying of turnings; to decrease sharply (by 60- 70%) the volume of LC combustion products; to reclaim the centrifuge fugate and produce oil and servicecirculating water.Non-ferrous turning and primarily aluminum and copper alloys turning is a stable source of secondary raw materials for metallurgical works.Direct by lubricant-coolants (LC) of various types: synthetic, semi synthetic, oily and emulsions.On the base of investigations concerning various methods of the non-ferrous turning processing the favorable one has been selected taking in to consideration the economy, ecology and quality of the finished product (alloy). Two-stage process is developed. The main idea of the process is the elimination of the lubricant-coolants (LC) to the limit specified in advance. The applied method is centrifuging with subsequent final elimination of LC by thermal method.Constant value of LC content at the inlet of the thermal unit excludes practically the oxidation of metal and as a consequence increases the output by 10 –15 % in metallurgical processing."

Jan 1, 2003

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By M. Amani, A. Akbarinasab, M. Bazmandeh

The fourth iron ore production plant at Golgohar mining and industrial company consists a ball mill and wet medium intensity magnetic separators (3500 Guss). The ball mill product applies directly into MIMS and the MIMS concentrate directly transfers to the low intensity magnet separators (LIMS). The thickener is used for dewatering of MIMS and LIMS tailings. By sampling from streams of ball mill and separators, it was defined that the grade and iron recovery were 60% and 80% respectively while they would be 66% and 90% respectively based on the designing documentation. The average of P80 in the ball mill was 342 micron in a month that is coarser than optimized value. This problem was related to unsuitable operation of grinding. For optimization of grinding efficiency, the amount of charge volume was investigated as a variable. The measurements illustrated 32% charge volume. For increasing grinding efficiency, the charge volume was increased 1% and 1.6% in two stages. The results showed ball mill power draw average reached from 3650 kw to 4120 kw and the average P80 reached to 329 micron. All of parameters calculated about 35 day before and after change. Average of Ball mill feed iron ore grade before and after change was 49.24% and 50.32% respectively. This change caused an increase in efficiency of MIMS, where the enrichment ratio and concentrate grade increased 2% and 1.9% respectively. For increasing the iron grade of the MIMS concentrate; the orifice of the tail flow exit pipe changed from 4 inch to 6 inch and the concentrate grade increased 2%.

Jan 1, 2014

By Andrey Kozlov

The results of mineralogical?technological studies of PGM mineralization in zoned mafic?ultramafic complexes of the Ural?Alaskan type are given. The most important technological specificity of PGM mineralization hosted in dunites is its occurrence only in the form of free mineral species with predominance of Fe?Pt alloys (ferrous platinum, isoferroplatinum, and tetraferroplatinum). Technological properties, grain size, and good opening of PGM ore in grain size class +80 µm make it possible to concentrate ore using gravity methods with stadial comminution and between cycle separation of relatively large grains and nuggets into high-grade concentrates at the early stage of disintegration. Keywords: platiniferous dunites, PGM mineralization, mineralogical?technological studies and processibility research, recovery technology, gravity methods

Sep 1, 2012

By Kilian Neubert, Hermann Wotruba, Henning Knapp

Sensor-based sorting has been integrated into more and more applications in mineral processing over the past decades. Various sensor types, such as line scan cameras, near infrared sensors and X-ray transmission sensors, allow the separation of a vast variety of raw materials. Sensor-based sorting has several economic benefits which can make the difference between an uneconomic operation and a profitable mine. Sensor-based sorters can be applied to fulfill various sorting tasks, such as waste rejection, product quality improvement and ore type diversion, and have a significant impact on the layout of the processing plant. Therefore, it is important to include sensor-based sorting into the planning of a processing plant at an early stage. To evaluate the applicability of sensor-based sorting for any specific ore type, it is currently necessary to provide several hundred kilograms of material for subsequent bulk tests. In exploration, ore samples are usually rare and only available in form of drill cores. The acquisition of drill cores is time-consuming and expensive especially for deposits in great depth. Hence, it is unfavorable to spoil valuable drill cores for bulk tests. This paper describes a methodology to evaluate the applicability of sensor-based sorting based on drill core analysis. That methodology offers the possibility to calculate the achievable performances of different sensor types for various grain sizes without comminution of drill cores. The general methodology is shown on basis of an exemplary test work on drill cores from a currently conducted exploration.

Jan 1, 2014

By C. Abbruzzese, F. Vegliò, S. Ubaldini, R. Massidda

"Gold solubilised during cyanidation can be recovered by precipitation (Merrill-Crow process) or by adsorption onto activated carbon, these being the techniques applied in industrial plants.Precious metals (Au, Ag) adsorbed onto activated carbon are extracted during a subsequent stage in aqueous phase, by various technologies, such as hot elution (70-80°C) or under pression desorption (100-130°), with hydro-alcoholic solutions.This stage is of great interest from an economic point of view, due to the high energy costs. Temperature represents the critical kinetic factor.The aim of this paper was to study the influence of different water/organic solvent mixtures (isopropyl alcohol, ethanol and ethylene glycol) on the desorption process.The experimental work was carried out on laboratory scale, using activated coconut carbon with different temperatures and extraction times, without adding cyanide.Best results have been obtained in this order: isopropyl alcohol > ethylene glycol > ethanol. Starting from gold concentration of about 5 g Au per kg of carbon, best kinetics resulted in 97-100% of gold extraction, after 8 hours of desorption, at a temperature of 80ºC."

Jan 1, 2003

By Hermann Wotruba, Günther Petzold, Fabian Riedel

"Increased mechanisation in underground stoping operations results in higher waste percentages in the run of mine. A new method of reducing waste is optical sorting. Optical sorters have low maintenance costs and can be installed underground. Rejected waste can be backfilled directly without having to be hoisted, therefore increasing the shaft capacity for a more valuable product.Pre-Concentration by Optical SortingA series of tests with an optical sorter at the laboratories of the Mineral Processing Department of the RWTH Aachen have shown that it is technically possible to sort almost any kind of ROM which has even slight differences in colour (Platinum Reef, Gold Reef, Kimberlites, Industrial Minerals, Aggregates, Coal, etc.).By employing optical sorters prior to conventional sorting plants, it is possible to reduce the amount of waste to be processed. Figure one shows test results of ore which is quite similar in colour to the waste (grey). With increasing waste in the feed, the recovery decreases according to the graph. In figure two, the colour ratio parameter of the sorter was changed with a similar waste percentage in the feed. With increasing loss of ore, a cleaner product can be achieved. Before designing a sorting plant, throughput tests are carried out. Throughputs vary depending on the size range. Sorters have a limit of about 250mm top size. In this upper size range, throughputs of 150t/h can be achieved."

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Khoi Nguyen, Keeney. Luke

An outcome of geometallurgical mapping and modeling is the generation of continuous down hole profiles of quantitative geometallurgical attributes at assay scale. These attributes vary from traditional routine data collection methods such as assays and geotechnical logging (e.g. RQD, Fracture Frequency), to new measurements including petrophysical attributes, EQUOtip hardness data and modelled estimates of metallurgical performance indices (e.g. A*b, BMWi). Highly variable continuous geometallurgical data with high spatial resolution can make it difficult to identify spatially continuous domains. An automated method based on the well known time series analysis technique of cumulative summation (CuSum) has been developed which uses statistical analysis to identify domain boundaries in down hole profiles. A bootstrap analysis automatically identifies potential domain boundary locations with associated confidence levels and a series of t-tests determine the significance of defined populations. A hierarchical clustering algorithm is applied to results to enable data sensitivity to be taken into account. The method produces statistically significant populations and is suitable for application on either single or multiple drill hole datasets. Domains defined preserve the inherent variability of the continuous down hole data and provide a method for scaling up variability data (i.e. assay interval scale) to mine scale (i.e. bench scale, block model). A major advantage of the method is its ability to provide suitable input parameters for use in spatial modeling of non-additive and non-linear geometallurgical attributes through conditional simulation techniques.

Jan 1, 2014

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003