Search Documents

By O. E. Andrew

THE object of this paper is to present a brief summary of the dust control system in use on the 3,825-foot level at the jaw crusher station, Lake Shore mine. During the years 1936 and 1937, dust survey reports were presented to the management showing that high dust concentrations were being created during operating periods. At that time, however, this crusher was running only an hour or so each shift, and it was felt that no large capital expenditure for dust control equipment could be justified. In order to afford some protection to the operators, a number of respirators then on the market were .tested and the 'Comfo' respirator was adopted for use by the crusher-men. In 1938 this crusher began to handle a large share of the total mine tonnage and the hours of operation were increased. Further dust sampling showed increased dustiness with the longer operating time. It was also realized that the operators suffered considerable inconvenience if they wore their respirators throughout the shift. If the respirators were not worn, then dangerous amounts of dust were being inhaled. The fact that the crusher station was situated on the 3,825-foot level limited the means that could be employed to eliminate the dust hazard. At that rime there was not available the 5,000 c.f.m. of fresh air which would be required to sweep out or dilute0 the dust, and there was also no way of disposing of the contaminated air without passing it on for other men to breathe. Thus it became apparent that a self-contained dust disposal system would have to be installed.

Jan 1, 1941

By E. Poiate, P. A. L. P. Firme, D. Roehl, M. A. Carrion, A. M. Costa

Drilling high-pressure/high-temperature wells in salt rock formations is still a challenge for the energy industry. Creep and solubility is part of the salt rock physical-chemical behaviour, which must be considered in the design of the wells. The stress redistribution caused by drilling, in addition to thermallyactivated processes, triggers creep deformation, leading to borehole closure and the imposition of loads on the casing. The drilling fluid is designed by computer modeling in order to control the creep strain rate to a limit which allows the drilling operations and the casing setting. Depending upon the composition of the drilling fluid, chemical reactions on the salt wall may occur, especially in case of water-based fluids in highly soluble salt rocks. In those cases, cavities by dissolution (washouts) can be generated and the casing column remains uncovered by the cementation and laterally unconfined along the cavity length. This scenario is propitious to the loss of integrity of the casing due to phenomena such as plastic collapse, buckling and non-uniform loading on the casing provoked by the closure of salt formation around it. The casing should remain intact during the wellbore life-time. In this work, a section of a typical well crossing salt formation composed by halite and carnallite is considered. An idealized-cylindrical washout cavity inside a highly soluble salt layer is assumed. The purpose here is to evaluate the effect of the dimensions of the cavity on the integrity of the casing. Several typical diameters and lengths of the cavity are adopted. Numerical analyses are carried out with an in-house finite-element system composed by the pre-processor MTOOL 3D®, the simulator ANVEC 3D® and the post-processor POS 3D®. Salt rocks are modeled as visco-elastic materials. Creep is simulated by the Double Mechanism Creep Law, widely employed in Brazilian salt rock mechanics research. Cement and casing (steel) are modeled as elasto-plastic materials described by the Mohr-Coulomb and the von Mises criteria, respectively. Casing integrity is evaluated with respect to vertical and horizontal displacements. Vertical displacements imposed to the casing can provoke the failure of the column by plastic collapse or by buckling. Besides that, horizontal displacements of salt due to creep closure shall lead to the undesirable contact with the casing. Failure envelopes based on displacements are generated. The results of the simulations have shown that the casing failure by plastic collapse occurs preferentially in short columns, as well as buckling occurs in long and slender columns. The occurrence of both failure modes is more frequent in large-diameter cavities. Additionally, failure caused by contact between salt and casing occurs preferentially in short-diameter cavities.

Jan 1, 2015

By D. F. Sherwin

"THE AREA which is described in this paper (Fig. 1) includes the continental margin of eastern Canada extending from the Gulf of Maine to the north edge of the Grand Banks, which, including the continental shelf, slope and rise, comprises an area of about 600,000 square miles. The paper is intended to give a background of the geological setting of this region in the context of its ultimate potential for oil and gas reserves in close proximity to the Nova Scotia energy market.HISTORY OF EXPLORATIONThe history of geological exploration of this area really began in 1878, when U.S. fishing boats brought back samples of rock recovered in trawls from their expeditions to the long-famous fishing banks off Canada's East Coast. Tertiary and Cretaceous fossils recovered from these samples indicated that the eastern Canadian continental shelf was actually the submerged northern extension of the Atlantic Coastal Plain."

Jan 1, 1972

By Jiahao Xu, Namsoo P. Kim, Guikuan Yue

Iron (ferrous ions and ferric ions) plays an important role in the heap leaching of copper sulfide minerals and copper electrowinning. In our previous study, a novel oxidation-reduction potential (ORP) equation only based on the variables of temperature and nominal ferric/ferrous ratio was developed to predict the redox potential of the quaternary H2SO4-Fe2(SO4)3-FeSO4-H2O system, and its applicability was also extended to more complex acidic iron sulfate solutions, especially those generated during the acidic leaching and bioleaching of Printed Circuit Boards (PCBs) to recover copper. In this work, the broader range of applicability of this equation to other complicated acidic iron solutions containing copper ions has been extended and determined. Specifically, synthetic iron-containing solutions with copper ions according to the conditions of industrial electrolyte during copper electrowinning and heap leaching have been used to measure the ORP and test the developed equation. It seems that this equation can still be employed to predict the redox potential of the Fe3+/Fe2+ couple for the simulated solutions under conditions related to copper electrowinning and pregnant leaching solution generated during heap leaching over a wide range of solution concentration, nominal Fe3+/Fe2+ ratio and temperature. It has shown that the prediction and measurement of redox potential is highly useful to estimate and understand the iron chemistry of industrial leaching and electrowinning processes. INTRODUCTION It is well-known that iron (ferric or ferrous) ions are widely involved in the hydrometallurgical production of non-ferrous metals such as Cu, Au and Zn, mainly in the form of acidic iron sulfate solutions. As far as Cu is concerned, in a typical leaching-solvent extraction-electrowinning process, ferric ion plays a central role in the heap leaching process and is reduced to ferrous ions in the pregnant leaching solution. Ferric ion is the most important surrogate oxidant and the dissolved ferric/ferrous couple plays an important catalytic role in accelerating the leaching rate with oxygen as an oxidant (Peters et al., 1986; Schlesinger, King, Sole, & Davenport, 2011). In addition, during the traditional electro-winning process, oxygen is evolved at the anode, and copper is reduced at the cathode. A common idea is that iron in the electrolyte in copper electrowinning cell (with total iron of 1–4.4 g/L) plays an important role in reducing the current efficiency. According to the published results (Winand et al., 1975; Dew et al., 1985; Moats et al., 2009; Khouraibchia et al., 2010), thecurrent efficiency decreases linearly with increasing ferric ion concentration and the energy consumption increase was mainly caused by the decrease in current efficiency.

Jan 1, 2019

By C. Bissue, G. M. Castillo

Newmont’s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By Sobczyk

The article will present a comparison of classifications of resources according to the JORC Code System with Polish classification, basing on system used in Eastern Europe. The differences between these classifications are significant. The information about mineral resources in Poland is not comparable to the main international system of reporting reserves like JORC, SAMREC, and PERC. Although comparisons between these systems are used, the transfer of particular categories of resources from the Polish system into a JORC category is not simple. Basing on the examples of privatization of Polish coal companies through initial public offering on the Warsaw Stock Exchange, the current practices providing guidelines how to convert resources from the Polish classification to the JORC system are described. Such independent assessment of resources is necessary for development of Mineral Expert?s Report (MER or CPR) which is an integral attachment to the prospectus.

Aug 1, 2013

By Donald S. Cameron

By dispersing gold in high surface area form supported on metal oxides, its inert character can be transformed to make economical, effective catalysts. Gold has already been demonstrated in a number of fuel cell applications such as gas phase catalysts, electro-catalysts, and electrical connectors. In this paper, the various types of fuel cell systems are reviewed, and several opportunities for gold identified. Low temperature fuel cells, including alkaline and solid polymer electrolyte types rely on high surface area platinum group metal catalysts which are highly susceptible to poisoning by low concentrations of carbon monoxide in the fuel supply. Hydrogen is frequently obtained by steam reforming hydrocarbons, followed by the water gas shift (WGS) reaction. A promising initial use for supported gold catalysts is in catalysing this WGS reaction. Research has shown that gold supported on iron oxide (Au/a-Fe2O3 ) WGS catalysts are more active than the current commercial copper oxide / zinc oxide catalysts, and effective at temperatures as low as 120oC. Products from reformer/ water gas shift reactors can be further purified by removing traces of carbon monoxide. If a small proportion of oxygen is introduced into the fuel gas stream, carbon monoxide can be preferentially oxidized to carbon dioxide even in the presence of hydrogen. Gold nanoparticle catalysts on iron oxide support (Au/a-Fe2O3 ) have exhibited higher activity than commercially available platinum on alumina (Pt/?- Al2O3 ) preferential oxidation catalysts. The low temperature of this reaction may make it feasible to incorporate these catalysts within the fuel cell itself. Proton exchange fuel cells provide several possible applications for catalytically active gold and its alloys. Carbon supported platinum group metals would benefit greatly from improved electrical conductivity if gold replaced some or all of the carbon support material. As electrode current densities are raised, electrical resistance constitutes an increasing proportion of voltage losses within the fuel cell. Dramatic reductions in cell stack voltage losses have already been demonstrated by reducing inter-cell contact resistance using gold plating. The low temperature oxidation properties of gold catalysts have been investigated in controlling gaseous emissions from direct methanol fuel cells, and gold also provides essential catalysis in building direct borohydride oxidation fuel cells. The prospect of a range of other applications for gold in fuel cells to contribute useful improvements in corrosion resistance and conductivity is assessed. Globally, fuel cells have been developed for a wide range of applications including stationary generators, cars and buses, industrial vehicles and small portable power supplies, each of which represents a substantial market. Hence there are likely to be many and varied opportunities for gold catalysts to contribute to the performance and economics of the systems being commercialized.

Oct 1, 2003

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d'or"" analyse, dans une approche systémique, les travaux d'évaluation et de mise en valeur des gisements minéraux dans l'axe de la géologie, dans l'axée l'ingénierie et dans I ‘axe de l'économique. L’objectif est d'identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l'évaluation et de l'exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d'investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d'inventorie et de classification des réserves aux méthodes d'évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s'étendent qu’à l'axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l'information dans les axes de la géologie, de l'ingénierie et de l'économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d'évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s'inspire du Code australasien, peut facilement et rapidement s'intégrer dans les pratiques de l'industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l'échelle internationale. La proposition d'utiliser les marges d'erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu'une période de rodage."

Jan 1, 1992

By Arthur Lieu

Outline Removal mechanisms of Se and Mo in the Key Lake Bulk Neutralization circuit Bulk circuit Detail process modification in the Key Lake BN circuit Process performance after commissioning Objective Legacy effects of Se and Mo from the historical operation of Key Lake mill were shown to have an negative effect on the regional biota in the downstream environment. The water treatment circuit was not designed to remove Se and Mo from the effluent. Reduce Se and Mo concentrations in final effluent under0.028 0.028 ppm ppm and 0.3 and ppm ppm(CNSC regulatory limits).(limits).??????

Nov 1, 2011

By A. L. Karyakin

The report focuses on the process measurements of the mass of rock in the bucket power shovels and dragline excavators. The mathematical models are suggested of AC and DC electric drives of excavators. These models are a basis for calculation methods of the electric drive electromagnetic torque. The design schemes of mechanical equipment of excavators considered to account the situation of bucket in the plane of the boom. The methods of static moment allocation and identification of the excavator technological operations are developed. The results of the work are experimentally tested on power shovels with bucket capacity of 12 and 18 m3.

Aug 1, 2013

By F. Parada L

Two copper concentrate with medium and high enargite content were leached in a 3 L autoclave reactor under conditions based on the CESL process. Copper, arsenic, sulfur and iron were checked in all the experiments and antimony, zinc and molybdenum were evaluated in selected tests. The 98% of the obtained copper extraction is agree with others authors, but the behavior of arsenic, iron an sulfur have some differences. The solid residue was characterized by chemical analysis, DRX and QEMSCAN®. Finally a comparative analysis with neutral roasting as an option for the treatment of this concentrate is done.

Jan 1, 2014

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By A. Plugatyr, C. P. Baxter

"Bessemer matte iron content is a critical process parameter that needs to be closely monitored and controlled in order to achieve optimal Ni/Cu smelter returns. Current process control practices during Ni/Cu converting often rely on visual observations and typically involve matte sampling to confirm that target composition was reached. A high-level techno-economic analysis study was carried out to evaluate potential direct benefits of advanced process control during the final stages of Ni/Cu matte converting. The results indicate that the magnitude of direct benefits will largely depend on matte iron control practices already implemented as well as matte iron set point. Preliminary assessment suggests that under the assumptions used in this study, implementation of advanced process control can potentially result in additional revenues ranging from several hundreds of thousands to tens of millions of US dollars per year per converter producing about 200 tonnes of Bessemer matte per day based on Ni, Cu, and Co metal recoveries alone.INTRODUCTION Real-time measurement of molten metal elemental composition, arguably, remains one of the key unresolved issues impeding full automation and real-time optimization of pyrometallurgical operations in different industrial areas, including non-ferrous metals and ferro-alloys. In particular, current process control practices during Ni/Cu matte converting often rely on visual observations and typically involve matte sampling in order to confirm target matte composition. In addition to being time consuming, this approach relies heavily on operator experience and diligence, and, therefore, requires continuous performance and quality control efforts. For instance, the need to improve quality of the Bessemer matte (BM) at the Copper Cliff smelter has prompted an impressive staff engagement and training campaign that was carried out by Vale’s team in the late 2000’s (Zanini, Wong, & Cooke, 2012). This training exercise was executed to address the compounded effect of several operational challenges, namely demand for higher throughputs, changes in the feed concentrate composition, increased feed variability, loss of process knowledge and expertise due to retirement, as well as lack of a comprehensive approach to improving the overall performance of the flowsheet rather than meeting production targets for intermediate products. Although the campaign was very successful and has resulted in significant improvements in the Bessemer matte quality, it has also highlighted the need to move away from “the-art-of-converting” and develop analytical tools that would enable real-time process monitoring."

Jan 1, 2018

By G. Stokreef, B. R. Davis, M. Kadiyski, T. LeBel, Alvear Montenegro, R. Parra, V. Montenegro

A drop tower and methodology were developed to study the impact of mineralogy on the flash combustion behaviour of copper concentrates. Reaction shaft conditions of a flash furnace were simulated using a drop tower reactor and different molar ratios of oxygen gas to sulphur in the feed. Five feeds were tested in the drop tower including pure minerals chalcopyrite and pyrite as well as two mineralogically distinct copper concentrates and a blend of the two. The behaviour of each of these five feeds were evaluated through analysis of the solid combustion products for elemental sulphur, mineralogy and particle size. Desulphurization curves for each of the feeds were produced. It is thought that the desulphurization behaviour of pure minerals can be used to estimate the behaviour of a concentrate and that a blending recipe could be developed, which can optimize the chemical and mineralogical inputs to the flash furnace and guide operations on the optimum furnace conditions. Overall, the drop tower has proven to be a useful tool for studying flash combustion processes. Experimental results suggest that mineralogy has a significant impact on the conditions required for the production of matte with consistent grade. This finding is especially significant for custom smelters, which may see several different blends in a day. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process that is used to produce copper matte from copper sulphide concentrates. Dried concentrate(s), silica flux, and secondary materials are blended to a target chemical composition, typically given by the Cu/S ratio, before processing. This fine, dried feed is dispersed throughout the heated furnace reaction shaft with an O2-enriched reaction gas. The particles heat up in the shaft of the furnace, ignite and undergo reactions that pre-oxidize the iron sulphide and some of the impurities in the feed. Oxidation reactions in the shaft of the furnace desulphurize the feed and produce an SO2-containing off gas. The reacted particles fall into the furnace settler and separate into a Cu-rich matte and an iron-silicate slag, while the SO2-containing off gas is carried out of the furnace for heat and dust recovery, as well as H2SO4 production. Some concerns during operation of the furnace are dusting, over or under oxidation of the feed, and a stable flame.

Jan 1, 2019

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By W. Haibei, Lei. Z., Z. Bangsheng, W. Yufang, J. Kaixi

In 2007 output of zinc was more than 3.71 million tons in China. Some new projects have finished FS and several new zinc plants are building now. In recent ten years it happened great changes in zinc industry. For zinc concentrates one pressure leaching plant was built with capacity 10,000t/a and at least four companies are carrying out FS or engineering design now. Direct atmospheric leaching will put into used in China in 2008 with capacity 100,000t/a. It is estimated that until 2010 the output of direct leaching will be 400,000t/a.

Jan 1, 2008

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019