Search Documents

By G. S. Hume

THE Plains of east-central Alberta herein described embrace an area from Viking east to the Saskatchewan boundary and from North Saskatchewan river south to Coronation and Monitor (Figure 1). By far the greater part of this area is deeply drift-covered, and .outcrops of bedrock are relatively few and often widely separated. Within the area there are large morainal hills and others of considerable extent that superficially have all the characters of morainal hills but contain a core of bedrock. These latter, then, were hills when the ice sheet traversed the country and only have been modified by glacial agencies. In many places on them, the drift is but a thin veneer, as is certainly the case in part of the Neutral hills (Figure 2) northeast of Coronation and north of Monitor. In other cases, however, as in the Blackfoot hills, southwest of Lloydminster, the drift is sufficiently thick to conceal practically all the bedrock and in many places no information is available as to whether a bedrock core, representing a pre-glacial hill, is present. There is no question, however, that the larger river valleys, as for example those of the North Saskatchewan and Battle rivers, are in part at least pre-glacial. Proof of this can be demonstrated in many places, because obviously the valleys must have been present in pre-glacial times to allow glacial deposits to have accumulated in them. It is also known that inter-glacial deposits occur. At one locality in Battle River valley, in sec. 30, tp. 45, range 2, west of the 4th mer., the following section occurs( l ): 15 feet of boulder clay with granite and other boulders. 56 feet of stratified sands, clays, and gravels containing pebbles of Precambrian rocks and fresh-water shells. From this it is apparent that the 56 feet of stratified sands, clays, and gravels must have derived their Precambrian pebbles from a previous glaciation of which the overlying boulder clay represents another ice advance in this area. Thus, although the river valleys contain glacial and interglacial deposits, they have not been filled by them to such an extent that the drainage has been diverted, and in many places, especially in the case of Battle river and some smaller streams, the size of the valley is altogether out of proportion to the size of the stream it now contains.

Jan 1, 1937

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By PAUL L. DEAN

Industrial mineral deposits are widespread in Newfoundland and Labrador and a variety of commodities are produced. The province has the only pyrophyllite mine in Canada and also produces asbestos, gypsum, silica, barite, limestone, gemstones, cement and other structural materials. Large reserves of these and other industrial minerals are known and several deposits are likely future producers. Most producers are wellestablished and have large tonnages of ore reserves.

Jan 1, 1984

By Mario A. Morin

Mine design, planning and scheduling is a very complex, iterative process comprising several interrelated and interdependent activities. Understanding how this process works, identifying the critical pieces of information and the decisions to be made is key to initiating business process improvements (BPI) or business process reengineering (BPR) activities. Fundamental to most BPI and BPR work is some form of systems analysis. Structured Analysis is a powerful systems analysis technique that is well suited for modeling and analyzing complex process activities. Through a series of diagrams, this paper presents a vertical slice through the analysis work performed for formally describing the underground hardrock mine design and planning process. These diagrams illustrate how simple graphic constructs can be used to decompose the most complex situations into easily understandable diagrams that facilitate understanding, communication, improvement and reengineering.

May 1, 2002

By W. S. McDonald

PRACTICALLY all dusts derived from organic matter are explosive and instances are recorded of explosions-some of them extremely violent-having occurred in grain elevators and flour mills. While a discussion of the explosibility of dusts in general, doubtless, would be of more than academic value, it will be of greater interest, on this occasion, to consider various phases of the problems connected with the hazards arising from coal dust. Extensive and valuable research has been carried out during the past few decades on the subject of coal-dust explosions and a great part of this work has been concerned with the preventive effect of stone or other incombustible dusts. Four men have been outstanding in this very substantial achievement. The first is Dr. W. Galloway, who succeeded in demonstrating by experiments that one pound of coal dust mixed with 150 cu. ft. of air formed an explosive mixture. The next is Sir W. Garforth, who proved that stone dust is an effective preventive for coal-dust explosion. The third is G. Haon, and last but not least, L. G. Hill, both of whom laboured incessantly to produce a suitable stone-dust and a satisfactory method of application. Today, mining men all over the world are satisfied and convinced that stone dust, if properly applied, will prove effective in greatly minimizing, if not completely preventing, explosions of coal dust, as has been demonstrated in experimental mines, as well as in actual explosions, in practically every coal mining industry.

Jan 1, 1938

By A. Proulx

Durant les années 1955 à 1961, plusieurs campagnes d?exploration ont été menées sur la zone Bond dans la partie sud-ouest de l?anneau nord de la carbonatite d?Oka (propriété de Niocan, figure 1). Les zones minéralisées HWM1 et HWM2 sont découvertes à l?ouest de la propriété. Un des forages, le S-60, avait intercepté 80 mètres de minéralisation à 0.71% Nb2O5 à l?est des zones HWM1 et HWM2 mais aucun autres travaux d?exploration n?avaient été réalisés sur cette interception minéralisée. En 1995, Niocan réalise une campagne de forage pour mieux définir la zone minéralisée recoupée par le forage S-60. En 1997, une seconde campagne de forage détermine un tonnage de 14.37 Mt avec une teneur de 0.66 % Nb2O5 pour la zone S-60 (Marcotte et Gagnon, 1997). Le complexe carbonatitique d'Oka se situe à environ 35 km à l?ouest de Montréal sur la rive nord du lac des Deux-Montagnes. Sa formation remonte au Crétacé précoce (entre 117 à 123 Ma). La carbonatite d?Oka fait partie de la suite d'intrusions alcalines que constituent les collines Montérégiennes. Le complexe a une forme allongée (7.2 km par 2.4 km) orientée NO-SE (figure 1). Il est intrusif dans des roches précambriennes constituées d?anorthosites au nord et de gneiss charnokitique au sud (Gold, 1963) appartenant à la Formation de la colline d?Oka. Les gneiss au contact du complexe sont fénitisés sur une épaisseur qui peut atteindre jusqu?à 60 mètres. Les roches carbonatitiques forment la série dominante du complexe et elles sont composées principalement de calcite (> 50 %) à gros grain et parfois rubanées. Les minéraux accessoires les plus communs sont la biotite, le pyroxène, la monticellite, la magnétite, l?apatite, la forstérite, la mélilite, le pyrochlore, la pérovskite, la niocalite, la pyrite et la pyrrhotite (Gold, 1963).

May 1, 2003

By D. B. Haas

THE HYDRAULIC TRANSPORT of solids is becoming increasingly prevalent throughout the world. Major long-distance slurry pipelines currently in operation transport commodities such as coal and various ore concentrates distances of up to hundreds of miles. In the United States, a number of large-diameter, high-tonnage pipelines are under consideration for the transport of Western Plains coal to markets up to 1000 miles away. In these and other applications, the solids are generally quite fine, with 14 mesh being a typical limit of particle size for long-distance (over 100 miles) slurry transport. There are applications where it might be practical to transport solids consisting of larger particles distances of up t o 100 miles. Deposits of high-quality metallurgical coal are found in the inner foothills belt along the eastern edge of the Rocky Mountains on the Alberta-B. C. border. There are few existing railroad s and the possibilities of constructing extensions are limited because of environmental and economic factor s. In these circumstances, the most efficient transportation system might consist of a pipeline to transport the coal from the mine to beneficiation plants located near existing railroads 50 or 100 miles away. Such systems would minimize environmental effects, capital cost s and operating costs. To determine whether such a system would be technically feasible, experimental testing is needed to determine the energy requirements for transporting coarse coal in a pipe line. Currently, run-of-mine metallurgical coal is crushed to less than 1 1/2 inches before going to the beneficiation plant. In the proposed scheme, coal of this size would be transported through a pipeline to the beneficiation plant located at the railroad. The Transportation Development Agency and the Department of Supply and Services have awarded a contract to the Saskatchewan Research Council to study pipelining of coarse coal in pipelines ranging from 4 inches to 12 inches in diameter.

Jan 1, 1977

By J. D. Little

"THE SALMO PROPERTIES of Canadian Exploration, Limited comprise forty-one Crown-granted mineral claims situated on Iron mountain between Sheep creek (on the north) and Lost creek, some eight miles southward from Salmo, in the Nelson mining division (see Figure 1). On these claims there are at present four operating mines. These are, from north to south, the Dodger, Feeney, and Emerald, all tungsten mines, and the Jersey, a lead-zinc mine, about 7,000 feet south of the Dodger. About midway between the Dodger and the Jersey is a fifth mine, the Emerald lead-zinc mine, which was the first producer in the area but has been inactive since 1926. The locations of the mines are shown in Figure 2.Records of prospecting and claim staking on Iron mountain -which owes its name to the presence of large iron-stained outcrops -go back to 1895. The first recorded owner of the claims that form the old Emerald lead-zinc mine was John Waldbeser who, in 1908, did considerable work and produced 426 tons of lead ore valued, at the then price of lead, at $7,000. This ore was chiefly lead carbonate and was taken from the surface outcrops of two bands of ore that form the Emerald orebodies. In 1909, the Emerald was the largest lead producer in the Nelson mining district."

Jan 1, 1953

By C. M. Campbell

The Inconceivable Wealth propaganda goes on apace. Premier King, at Vancouver, has stated that we still have, untouched, natural resources, "beyond the wildest dreams." Principal Currie, in an address before the Canadian Society in New York said that Canada's resources, "are as yet merely scratched and it is not possible to compute her almost fabulous natural wealth." Mr. Meighen, in the last election campaign announced that, "under the providence of God, Canada is more richly endowed, perhaps, than any other country in the world." Four years ago a despatch was sent to Premier King "on behalf of" this Institute advising him that "Inconceivable Wealth" in minerals in this country was assured. This was made as a statement ~f "incontrovertible fact." Specifically, this despatch stated that this wealth was on such a scale that the mining industry would in the future lead all others in this country. This inventory is still in effect as far as this Institute is concerned.

Jan 1, 1926

By P. Tarassoff

Extractive metallurgy is concerned with the winning of metals from their ores and concentrates. It is therefore not unexpected that extractive metallurgy in Canada has always been closely linked with mining. The discovery and exploitation of new orebodies has provided the impetus for the building of many of our smelters and refineries - past and present - and for the development of new metal extraction processes. The purpose of this paper is to provide a brief overview of those early metallurgical developments, and to highlight the continuing expansion and diversification of the Canadian metallurgical industry.

Jan 1, 1999

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By J. P. Morris, J. T. Novak, E. A. Sarver

"A variety of reagents are utilized in coal preparation, but aside from performing their desired function relatively little is known about the behavior of these reagents within the processing circuits. Where exactly do reagents go once dosed? In this paper, we present preliminary results of partitioning studies on frother (i.e., MIBC) and collector (i.e., diesel) chemicals commonly used in coal flotation, and examine implications for water management (e.g., in closed-loop systems). Additionally, we discuss the usefulness of such data in predicting environmental transport and fate of chemicals – which is currently a top priority for industry.INTRODUCTIONThe purpose of coal preparation is to upgrade mined coal into more valuable products. Since coal is primarily used as a fuel source for electricity generation, product specifications are typically contracted to minimize unwanted constituents that detract from the overall heat value (e.g., ash and moisture) or that add to environmental pollution or other problems like corrosion at a power plant (e.g., sulfur) (Pitt & Millward, 1979). Failure to meet specifications results in a financial penalty for the coal producer (Szwilski, 1986), and thus preparation processes have evolved to simultaneously optimize recovery of valuable “clean” coal with rejection of mineral matter and moisture. In addition to advancements in equipment and circuitry, development and application of various chemical reagents has dramatically improved the performance of coal preparation processes.Contemporary preparation plants typically include multiple circuits that can be categorized by the size of particles they process: coarse, intermediate, and fine/ultra-fine (Figure 1). Coarse and intermediate circuits generally rely on size classification and gravity separations (e.g., dense-media cyclones), and do not require significant chemical reagents. However, fine and ultra-fine circuits often use froth flotation to separate coal from impurities, which requires chemical additives (Table 1). The primary additives include collectors, which coat the surface of the coal particles to render them (more) hydrophobic and thus more likely to attach to air bubbles and float; and frothers, which aid in the formation and stability of the froth that will accumulate the floated coal particles. Modifiers are also commonly added to flotation circuits to regulate pH in instances where coal or impurity characteristics may change water chemistries (Laskowski, 2001). Following flotation, coagulants and flocculants are often utilized in solid-liquid separations (i.e., dewatering or clarification) for coal products, and for tailings slurries prior to their disposal in impoundments. Coagulants function via double-layer compression1 to bring colloidal particles together, while flocculants promote bridging between the grouped colloids – and the combined result is enhanced sedimentation (Wills, 2006). Defoaming or anti-foaming agents may also be required to avoid fouling of dewatering operations."

Jan 1, 2012

By Nirmal Weerasekara, Jochen Franke, Malcolm Powell, John Favier

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By S. Boisvert

Risk-based Inspection (RBI) addresses the challenges associated with ageing plants by focusing the inspection effort on the process equipments with the highest risk, thereby improving plant safety and reducing inspection costs. The RBI methodology is commonly used in the oil industry through the API 581 standard. Since no such standard exists in the mining and metals industry, BPR-Bechtel has developed one using inspection data from process equipments in CEZinc. Models were developed for various damage mechanisms, such as uniform corrosion and stress corrosion cracking. The equations were organized into a user friendly software that facilitates the implementation process.

Jan 1, 2010

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By Theophile Yameogo

Much has been said about the methodology of geomechanical design in underground excavations. However, the geological, hydrogeological and geotechnical complexities encountered at the production horizons in the Athabasca Basin commanded for a novel approach in the geomechanical assessment and design of underground openings. Rock mechanics engineers at Cameco McArthur River have been able to establish a practical methodology that goes beyond known conceptual approaches. In this paper, the author describes the original challenges and unique approach in the geomechanical assessment for drifts and chambers development. The example of the successful development of the 510-8225N Chamber will also be presented.

Aug 1, 2010

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By Theophile Yameogo

The rock mechanics literature has documented the challenges, failures and successes of tunneling through weak rocks. Cases usually deal with low RMR rock masses or high stresses in a fractured zone. With the combination of 5MPa water pressure, 14 RMR ground with clay infillings and ground freeze walls, the case of the 510-8225N development drift at McArthur River is certainly much more challenging, especially when high grade uranium production is at stake. The article explains the excavation and the ground control techniques that were used to overcome the challenges of development at the Unconformity in the Athabasca Basin.

Aug 1, 2010

By D. King

Outline ? Regional Geology and Deposit types ? PM Deposit Exploration History and FNX?s Exploration Strategy ? Deposit Geology and Interpretation ? Resource Estimation ? Reconciliation ? Conclusions ? Breccia of comminuted footwall rocks from passage of shock wave due to meteorite impact ? Matrix ?pseudotachylite?-like? ? Variable re-crystallization of matrix due to thermal metamorphism &/or alteration

May 1, 2006