Search Documents

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By W. J. Bennett

WHEN Dr. Horace Fraser, your President, invited me to speak to you today I advised him in confidence that I was leaving my present positions on April 30th. In the circumstances it seemed to me that this audience might prefer to have as its speaker one who wo.uld J1ave a continuing association with the atomic energy programme. Dr. Fraser was kind enough to suggest that my re-marks might he of special interest to you, since I would be able to sum up my views on the atomic energy programme. I hope that I will not disappoint him or you on that score. I am particularly pleased that my last public appearance in my present positions should be at the Annual Convention of the C.I.M. since, as all of you know, a very important part of my work has been in the mining field. As it happens, my first public address on the subject of atomic energy and its raw material -uranium -was made at your Annual Convention in Montreal in April, 1949. It seems fitting that my final address should also be made at this convention -nine years later.

Jan 1, 1958

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By Azadeh Riahi

The main goal of this paper is to investigate the effects of permeability anisotropy in Large Open Pit (LOP) mines for problems that exhibit homogeneous anisotropic characteristics. The most important effect of the groundwater flow in open pit mines is on the stability of the pit slopes. This study will investigate the effects of having increased permeability in both horizontal and vertical directions on three aspects of LOP behavior, location of phreatic surface, pore pressure distribution and stability of slopes. The hydromechanical coupling is simulated using a one-way coupling approach. The Shear Strength Reduction method (SSR) is applied to assess the stability of slopes. The studies performed in this paper suggest that anisotropy in permeability leads to a significantly different regime of pore pressure dissipation depending on two aspects, ratio of anisotropy and the relative magnitude of permeability to simulated time. As a result, variation in safety factors and the location and depth of the failure surface must be expected.

Jun 1, 2012

By Bahjat Khoshaba, Bern Klein, Haixing Yan, Libin Tong, Andrew Bamber

"When a conductive or magnetic particle was put into an electromagnetic field introduced by an electromagnetic sensor, the particle can influence the electromagnetic field which can be used to characterize this particle. The electromagnetic technology based on eddy current theory was explored to investigate its potential in both the separation of minerals and the pre-concentration of a base metal ore. Samples tested in the study included the minerals obtained from Ward’s Science and the low grade copper ore particles obtained from Mount Polley Mine. The effects of mineral type, sensor frequency, particle size, particle position on the sensor surface, and particle lift-off on the magnitude and phase of the electromagnetic spectra were investigated. The electromagnetic spectra of various minerals show that it is possible to separate chalcopyrite or magnetite from tested minerals, simply based on the magnitude of the spectra. The spectra of the ore particles were determined by the mineral in the particles with the strongest signal. The effect of the pre-concentration of the low grade copper ore is determined by the association of chalcopyrite with magnetite. Direct sorting is the mechanism in the separation of mineral particles, while indirect sorting is the mechanism for low grade ores.INTRODUCTIONSensor-based sorting technologies include radiometric, X-ray transmission, X-ray fluorescence, near infrared, photometric, inductive, microwave heating and so on. Sorting not only discards barren rocks away from the concentrator but also recovers metal bearing that would be lose to the waste dump. The benefits of pre-concentration using sensor-based sorting are achieved on reduced energy consumption for comminution and reduced water usage on a volume per weight of metal basis (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). Amongst others, high frequency electromagnetic sensors were developed for ore sorting at MineSense Technologies Ltd. and are subject of this paper. Improving the understanding of ore heterogeneity is the basis for developing a successful semi-bulk or bulk sorting systems by incorporating the sensors in the material handling equipment (MineSense Technologies Ltd., 2016). The present study focuses on the bulk sorting potential and bulk sorting mechanisms of the electromagnetic technology in the pre-concentration of minerals or ores."

Jan 1, 2016

By M. Härting, D. T. Britton, M. Nzikou Mamboukou

"Copper containing different types of nanocomposites have been characterized for nanolabelling and ID. Three types of the rare earth nanoparticles were used for this study, the oxide and the sulphur compound of the Eu and Tb. Characterization techniques uses SEM, and Raman for morphology, chemical composition, and optical characterization respectively. It has been shown that it is possible to include the rare earth particle in a copper matrix without damaging its physical properties. INTRODUCTIONThe development of new materials, often involves the addition of new properties without changing the beneficial properties of the original material (Chen et al., 2009; Khana et al., 2007; Patil et al., 2008). Nanocomposites are nanostructured materials, whose structural elements including clusters, crystallites or molecules, of dimensions ranging between 1 to 100 nm (Moriarty, 2001), or a composite material where one of the phases is a one, two or three dimensionally nanostructured material (Nanotechnology, 2006; Wang, 2001). Nanocomposite materials research is a fast growing area due to the high demand for materials for specialized applications (Edelstein & Cammarata, 1998), such as biolabelling, magnetic storage media, solar energy transformation (Jisen et al., 2004), and resistance welding applications (Bessergenev et al., 1997; Kwon et al.,2006).The properties of the nanocomposite materials depend not only on the properties of their individual parent materials, but also on their morphology and the interfacial characteristics. Thus, significant efforts have been focused on the control of the nanoscale structures via innovative synthesis approaches. Therefore, novel materials of unique properties may be obtained by combining properties from the parent constituents into a single material (Balan, 2006; Garcia et al., 2009). Possible effects of nanocomposites in the original material may include changes in the mechanical properties such as hardness , wear resistance (Rafaja et al., 1987), and electrical properties (Britton et al., 2003). The inclusion process may therefore be used to tailor materials to have particular mechanical, electrical and optical properties (Das et al., 2009). However, to fully understand the nanocomposite, it is necessary to study the fundamental properties of both the host matrix and the inclusions (Li, 2008)."

Jan 1, 2012

By Mohammed Rachek

Résumé : la mine d?Elhammam, opération du groupe minier Marocain Managem, est située au sud de la ville de Meknes à 63 km, elle exploite un gisement de fluorine depuis 1974. La minéralisation se présente sous forme de deux filons principaux orientés N45° avec un pendage variant de 65 à 90° NW, entre ces deux filons on note la présence d?une succession de filons satellites sécants. La méthode d?exploitation pratiquée depuis le démarrage de la mine est celle des chambres magasins, elle assure une cadence d?extraction annuelle de 250000 tonnes. Cette méthode favorisée par une très bonne compétence mécanique des épontes de la minéralisation a offert à l?exploitation une rentabilité très satisfaisante grâce à son faible coût mine. Les travaux de recherche géologique menés en parallèle à l?exploitation ont permis la découverte d?un nouveau secteur ?K-Est Gouaïda? (KEG) qui fait l?extension nord-est du gisement principal, la minéralisation de ce secteur se présente sous forme de deux filons très étendus latéralement (900 m d?extension) et présentant une puissance minéralisée irrégulière et très faible 1.2 m en moyenne, les épontes de la minéralisation sont constituées de schistes de qualité mécanique très faible. Vers la fin des années 1990, l?exploitation s?est orientée vers le développement minier du secteur KEG. Ce développement consiste à faire le choix adéquat de la méthode et de l?infrastructure minière pour l?exploitation de ce nouveau secteur, KEG. La méthode des chambres magasins, pratiquée dans le gisement principal avec un faible coût mine, n?est pas praticable dans le nouveau secteur à cause de la qualité de ses terrains, l?irrégularité de la morphologie de sa minéralisation et de la faible puissance des ses filons. Seule la méthode des tranches montantes remblayées (TMR) peut être applicable techniquement vu les spécifications suscitées de la nouvelle minéralisation, la TMR doit être appliquée sous sa variante mécanisée pour faire face au niveau exigé de la production. Après le pilotage de l?exploitation par TMR mécanisée dans le secteur KEG, il a été confirmé que cette méthode donne une grande satisfaction en matière de stabilité des terrains, sécurité, sélectivité, productivité et récupération du gisement, néanmoins elle reste pénalisée par un coût mine trop élevé pour garder le niveau de rentabilité recherché par l?exploitation d?un produit de faible valeur marchande telle que la fluorine. Dans l?objectif de rentabiliser l?exploitation du secteur KEG qui représente en réserves l?équivalent d?une durée de vie de 4 à 5 ans et d?assurer la pérennité de l?activité, l?exploitation en collaboration avec Reminex, la filiale d?ingénierie de Managem, a adapté une nouvelle variante de la TMR mécanisée dite TMR avec plan incliné sur remblai. Cette nouvelle variante de la TMR consiste à réduire au maximum les travaux dans le stérile en reconstituant un plan incliné sur le remblai à l?intérieur des filons pour faire évoluer en vertical l?exploitation des tranches en montant vers la tête d?un panneau de minerai. La variante des tranches montantes remblayées mécanisées avec plan incliné sur remblai a été imaginée et appliquer en 1978 dans la mine de fluorine de Burc située au Sud-Ouest de la France (Sicard et Mailloux, 1983). Imaginée pour une cadence annuelle de 30000 tonnes et une mécanisation très modérée cette variante a été adaptée par l?exploitation de la mine d?Elhammam en 2002 pour un haut degré de mécanisation et une cadence d?extraction annuelle de 250000 tonnes de minerai. Cette variante de la TMR est appliquée depuis le début de 2003 dans les chantiers du secteur KEG, elle présente les mêmes avantages techniques que la TMR mécanisée classique et elle a permis la réduction du volume des travaux d?infrastructure de 17.65 m à 6.25 m de travaux par 1000 tonnes de minerai. Ceci s?est traduit par une baisse du coût technique de la mine de 34% ce qui a donné un nouveau souffle à la mine pour assurer sa production et pour poursuivre la recherche géologique d?éventuelles zones à mettre en valeur.

Oct 1, 2004

By K. Maruyama, T. Nagasaka, R. d. Chairaksa-Fujimoto, T. Miki

Electric arc furnace dust or EAF dust is considered as a hazardous waste but contains a significant amount of economically attractive non-ferrous metals especially zinc as zinc ferrite (ZnFe2O4) and zincite (ZnO). The hydrometallurgical process is one alternative choice because it has the advantage of low energy consumption. The leaching of ZnO from the dust is very easy. However, the complex major zinc compound in EAF dust is ZnFe2O4, which is very stable and insoluble in alkaline or acidic media under delicate conditions, and causes the low zinc recovery yield by hydrometallurgical process. Moreover, halogens and heavy metals in the dust are also problematic. In order to develop a new effective EAF dust treatment process, the authors have proposed "CaO addition process" as pre-dust treatment to transform all of ZnFe2O4 in the EAF dust to ZnO and Ca2Fe2O5. In this study, the selective zinc leaching from the CaO treated EAF dust with NaOH and NH4Cl solutions was carried out. The effect of temperature, reaction time and solute concentration were systematically investigated. All of zinc in CaO treated EAF dust was successfully leached into both solutions.

Jan 1, 2014

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By Alan Bauer, Melvin A. Cook

Measured detonation pressures of "prills and oil" (94/6 ammonium nitrate/fuel oil) and three of the new "slurry" blasting agents are presented and compared with computed, ideal detonation pressures and with detonation pressures expected from the measured detonation velocities. Results seem to show that the peak pressure in the detonation wave in these cases is the Chapman-Jouguet pressure and that no "spike" exists in these detonation waves. The absence of the Zeldovich-von Neumann "spike" is noteworthy in view of the very long reaction zone lengths of these mixtures. The measured detonation pressure of one of the slurry blasting agents (DBA-3") under steel confinement ( 172 kilobars) is shown to be considerably greater than the ideal detonation pressure of 75 per cent gelatin dynamite (p. = 135 kilobars) despite the fact that the detonation was still somewhat non-ideal in "DBA-3," its computed ideal detonation pressure being 180 kb. The popular 94/b AN /FO blasting agent exhibited a detonation pressure of only 13.5 kb in 5" paper tubes, but 37.5 kb in 5"• steel pipe compared with a computed ideal pressure of 40 kb.

Jan 1, 1961

By G. A. Sutton

This paper, describes a case example from San Manuel mine, where in situ copper leaching of the supergene zone was done over a 14 year period (1986–1999) in conjunction with underground and open-pit mining operations of a copper porphyry deposit. In 1993–1994, testing of well fields was done to determine the amount of copper that would be recovered from in situ leaching of the supergene zone, which was composed primarily of chrysocolla and copper-clay minerals. It was determined that the leach fluid would reach 70% (‘sweep efficiency’) of the copper minerals and that 75% of them would be leached for a recovery of 52% of the acid soluble copper. However, the final results from Zone 6, which had the longest leach history, showed that approximately 42% of the acid soluble copper was recovered, indicating that the `sweep efficiency’ was closer to 55%. Comparison of drill-core assay data from two holes, one drilled before (ARM158) and the other after (SMO9607) leaching, also indicate that approximately 42% of the acid soluble copper was recovered. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to a combination of factors, including difficulty in maintaining fluid saturation, channeling effects and gypsum precipitation. INTRODUCTION In situ copper leaching at the San Manuel mine, Arizona, was initiated in 1986. It was recognized that some of the copper oxide resource was not going to be economically recoverable by conventional open pit and heap leach methods using solvent extraction and electrowinning (SXEW). A high stripping ratio would be required to access part of the resource. At the time, in situ leaching was becoming popular in the uranium industry but the approach was virtually unknown in the copper industry, especially not at a large scale.

Jan 1, 2019

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By F. J. Hrach, S. A. Gasiorowski, J. D. Bittner

"Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs.. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash. TECHNOLOGY OVERVIEWThe ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition.In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 – 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by interparticle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multistage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%."

Jan 1, 2012

By D. M. Baird

ABSTRACT A revised stratigraphic section of Carboniferous rocks which occupy about 700 square miles in southwestern Newfoundland is presented. Gypsum, which outcrops at thirty-five different localities, is found to belong to four principal zones in the section. The newly mapped structure of the region makes the otherwise random occurrences of gypsum appear as systematic outcroppings of the four zones which follow the regional structure. Details of several occurrences are given and those most advantageous for exploitation are pointed out. INTRODUCTION ROCKS of Carboniferous age occupy an area of about 700 square miles in southwestern Newfoundland. They occur in a belt, from 5 to 15 miles wide, which extends from the head of St. Georges bay southwestward for 65 miles to the mouth of Little Codroy river (see Figure 1). Several hundred feet of Pennsylvanian rocks overlie rocks of Mississippian age, which are at least 12,000 feet thick. The rocks of the Carboniferous section of Newfoundland are very similar to those of Nova Scotia and represent a northeastward continuation of the same palaeophysiographic conditions. Mississippian measures of Windsor equivalence include thick gypsum deposits which outcrop at many places and which extend under large areas as indicated by sink-holes and by structural considerations.

Jan 1, 1951

By Kéiko H. Hattori, Neil T. Pettigrew

"Abstract- The Legris Lake Complex is a northeast-trending, 7.3 km long by 3.5 km wide, maficultramafic intrusive complex located in the western Wabigoon Subprovince of the Archean Superior Province. It is one of a series of mafic-ultramafic igneous complexes, the most notable of which is the Lac des Iles Complex, host to Canada’s only producing Pd mine with reserves of 93.5 Mt grading 1.53 g/t Pd as of December 2001 (North American Palladium Ltd., Annual Report 2001). Cu-Ni- PGE mineralization was first discovered in the Legris Lake Complex by a local prospector late in 1999. Shortly thereafter, the property was jointly optioned by Avalon Ventures Ltd. and Starcore Resources Ltd., who continue to discover significant Cu-Ni-PGE mineralization.One of the most notable features of the Legris Lake Complex is the occurrence of extensive brecciation caused by multiple injections of volatile-rich magma. The Cu-Ni-PGE mineralization is hosted by leucogabbro within a 2 km long by 600 m wide, highly brecciated area in the northwestern area of the Complex. The mineralized rocks contain disseminated to blebby sulfides (1 to 5 vol.%), comprising chalcopyrite + pyrite ± pyrrhotite + millerite ± pentlandite, typically surrounded by epidote. The majority of the Cu-Ni-PGE mineralization displays low ratios of Pt/Pd (~0.20) and high ratios of Cu/Ni (~2.9), which are similar to those of the Lac des Iles and the River Valley mafic-ultramafic complexes. The lithologies in Legris Lake Complex bear similarities to the heterolithic gabbro of the Twilight and Roby Zone deposits at the nearby Lac des Iles mine. However, the mineralization at Legris Lake, which is restricted to leucogabbro overlying unmineralized clinopyroxenite, is similar to that of stratiform deposits such as the Stillwater and Munni Munni complexes. The mineralization at Legris Lake is best explained by the late-stage, immiscible separation of a sulfide melt from volatile-rich parental magmas and the subsequent minor redistribution of metals by deuteric fluids."

Jan 1, 2001

By John H. Schloen

"The object of this paper is to review electrolytic copper refining as it was in 1954(1), as it is now in 1984, and to comment on the many improvements which have been made in the last thirty years.In 1954, and even in 1984, the ASTM specification B 115 for cathode copper was 99.90% minimum copper plus silver content and 100% minimum electrical conductivity, IACS standard. However, to meet competition and to satisfy the requirements of the fabricators and the electrical industry, the electrolytic refinery must supply a product of 99.95% to 99.96% minimum copper content, and 101fJlo minimum electrical conductivity.The range of cathode impurities reported by 20 major copper refineries in 1954 are given in Table I.The much more rigid British Specification, DD 78, for high-purity cathode copper, specifies individual elements, as well as groups of elements, as shown in Table 2.The Svenska test has been replaced by a similar procedure which uses 2.r mm diameter wire. The ISO test is the one listed in the DD 78 specification. In Table 3, corresponding values for the Svenska and ISO test s are given for various wire bar coppers."

Jan 1, 1986

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950

By O. Bernal

The Sociedad Minera Cerro Verde S.A.A, a subsidiary of Phelps Dodge Mining Company, operates a copper mining facility located in southern Peru. This "mine-forleach" operation currently produces 90,000 mtpy of copper cathode from secondary sulfide ore utilizing crushing, leaching, solvent extraction and electrowinning processes. The leach solution handling and application rates have undergone constant development over the years. This paper discusses the improvements in leach application designed to: 1) satisfy the needs of the "lixiviant request rate", which requires the use of application rates as low as 3.5 L/h/m2 and as high as 15 Llhlm2 with variable rest periods according to the leach kinetics, and 2) alleviate the poor solution distribution on the surface of the leach heaps inherent to drip emitters. Low application rates result in poor surface solution distribution and the formation of upside down cones of dry, non-leached material in the top meter of stacked ore, with heavy jarosite and iron salt precipitation; moreover, ferric iron is lost as insoluble precipitates. On the other hand, high unit flows associated with poor agglomerate quality can lead to uneven solution flow patterns within the heap leading to solution short-circuits, fines migration, and ponding with adverse effects on acid consumption and recovery.

Jan 1, 2007