Search Documents

By Wauchope AMH

Arsenic residues from BHAS Refinery operations are currently treated to form a calcium arsenic compound and stored in lined dams on site. Laboratory and large scale work on these residues has resulted in the development of a hydrometallurgical process for production of arsenic trioxide. The process also recovers the material from the storage dams. The residues are hot water leached to produce an alkaline arsenic liquor. This liquor is mixed with material from the storage dams and lime to form a calcium arsenic precipitate. The precipitate is then reacted with sulphuric acid to form gypsum for return to the main plant, and an acidic arsenical solution. Metallurgical gas containing 3-6% sulphur dioxide is bubbled through the solution and on cooling arsenic trioxide is precipitated. The product contains in excess of 95% arsenic trioxide. Installation of a plant at Port Pirie based on this process is being evaluated by BRAS.

Jan 1, 1984

By H R. Phillips

Fresh air intake in an underground coal mine is of critical importance to the occupational health and safety of workers due to the dynamic, confined and dangerous nature of the mining environment. In most coal mines in South Africa, belt road is not separated from the fresh air intake to the sections. Intake air to coal production faces generally contains dust generated by conveyor belts, transfer points and travelling roads. Long roadways (up to a few kilometres in some of the existing mines) to the coal sections are involved in the ventilation circuits of individual sections. This leads to a progressive increase in the dust levels in the intake fresh air and thus high dust levels in the air delivered to the working sections downstream. In the process of reducing worker exposure to dust in the face area, attention to the monitoring of fresh intake air is generally given a low priority. This paper summarises the intake dust levels measured in selected South African underground coal mining sections over the past five years and its use as a parameter in assessing worker exposure to dust through a newly developed model called the Dust Exposure Level Index (DELI). Based on the measured data of the South African coal mines, the average section intake dust level was 0.78 mg/m3. Approximately 60 per cent of the samples collected for the study have exceeded the 0.5 mg/m3. The intake dust level measured at a longwall face was much higher than in the CM headings. The measured section intake dust levels furnish the South African coal mining industry with the latest depiction of the level of face area dust contamination due to the intake air. Further, this paper demonstrates the use of intake dust level as a parameter in estimating exposure levels of workers, as it clearly plays as a corner stone in effective control of exposure to face area respirable dust. It must be borne in mind that intake dust is a base level to the mine worker exposed to dust without carrying out any additional work in the section. If the intake air is seriously contaminated by airborne respirable dust; then the exposure of the workforce in the section will constantly be elevated by that background dust level.

Jan 1, 2005

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007

By M Rimes

This paper describes a technique to predict achievable head grades and likely variances from target grade for the Shovelanna Iron Ore Project, in the Pilbara region of Western Australia. The block model from which the production schedule is produced was created from a wide spaced drilling program and was classified as an Inferred Resource under the JORC Code. Ideally, production schedules and target grades would be determined using a combination of Proved and Probable reserves. However sometimes it is necessary to consider the requirements of potential off-take parties who have specific grade tolerances. A technique is needed to simulate mining sequences and grade variations early in the planning process, using an æexplorationÆ block model rather than the normal æminingÆ block model. Marketing contracts require examination whether the target grade {Fe, P, SiO2, Al2O3 can be kept constant, or must be revised during the life of the mine. A model (written in ExcelÖ using Visual Basic macros) develops a feasible, close to optimal, mine plan from block model data. Cut-off grades for minable ore are chosen. The model evaluates ore tonnage, grade and stripping ratio against depth. Outputs at this stage include plots of slices through the orebody, at nominated x, y and z coordinates, showing ore grade, waste, drill hole locations and topography. The model then searches for a feasible satisfactory mine plan. The initial grade target is the average for the identified ore blocks. The available block list (ABL) at any time is the set of ore blocks, any one of which can be mined without removing any other ore block. The entire initial ABL has an unacceptably large ætotal grade stressÆ, defined as [(Grade-Target)/Tolerance]2, summed over the four relevant minerals {Fe, P, SiO2, Al2O3}. The model trims the ABL, removing the block most harming the total stress. Trimming is repeated until the total grade stress reduces to an acceptable level. The trimmed ABL defines the first mine campaign. Removing the trimmed block set, a second ABL is exposed, which is again trimmed and mined. The process is automatic: a few seconds computation provides a complete mine plan. Re-running the model with adjusted grade limits quickly shows whether a uniform target can be achieved or whether the target must be modified during the mine life.

Jan 1, 2007

By M I. Pownceby, A Torpy, C Johnson, N C. Wilson

To extract uranium from low-grade, calcrete-hosted uranium (CHU) ore is challenging owing to the presence of carbonate and swelling clay gangue minerals that require an alkaline lixiviant to be used. Western Australia possesses ~75 000 U3O8 t in CHU resources. Improvements to alkaline leach extraction practices would improve the economic potential of these deposits.A column leach study of CHU ore was run for 105 days using an alkaline carbonate-bicarbonate lixiviant. The uranium content of the liquor plateaued after 75 days at ~275 mg U/L; the calculated maximum solution capacity was 800 mg U/L. Spiked peaks and troughs were seen in the data set beyond the 60th day, where concentrations ranged from 220 - 290 mg U/L, indicating possible cyclic uptake and loss of uranium from the solution.Pristine and leached ore samples were geochemically analysed and mineralogically characterised at high resolution using a field emission gun-electron probe micro-analyser (FEG-EPMA). Results showed that leached ore samples from the top of the column contained less carnotite than pristine ore. In contrast, leached ore samples from the column base contained regions with more carnotite than pristine ore, indicating precipitation. Three carnotite grain micro-structures were identified in the leached ore; fan-spherulite, granular and core-shell cubes, with evidence for multiple growth phases.Evidence of carnotite precipitation was seen at the edge of and in pore spaces within montmorillonite and dolomite grains. The point of zero charge of both minerals is lower than the pH of the lixiviant (pH 10.8), thus the mineral surfaces are negatively charged and would not attract UO2(CO3)34- ions out of solution. Similarly, the decrease in the uranium content of the lixiviant is not attributed to super-saturation, as this was unlikely to have been achieved. Work is ongoing to understand the reason for carnotite precipitation and the fluctuations in the lixiviant uranium concentration that are seen.CITATION:Johnson, C, Pownceby, M I, Wilson, N C and Torpy, A, 2013. Microscale characterisation of pristine and processed ore - implications for leaching calcrete-hosted uranium ore, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 303-316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

This paper is a summary of the general theory of sampling published by the author in 1975. Sampling is a random process and its the- ory is a study of the, numerous errors liable to take place in the course of its realization. A complete sampling scheme is a sequence of sampling (proper) and preparation stages . At each stage, the total error ET is the sum of : -.Sampling errors EE arising from the selection process itself. -Preparation errors EZ arising from the operations (crushing, transfer...) sup- ported by the sampled material. ET a EE + EZ . At each sampling stage, the (total) sampling error EE is the sum of seven inde- pendent errors : - Weighting error ED resulting from the non-uniformity of the density or rate-of-flow of the sampled material. - Integration error EI1 resulting from the long-range distribution heterogeneity of the sampled material. - Periodicity error EI3 resulting even- tually from periodic quality variations of the sampled material.

Jan 1, 1976

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

By Armstrong M

The highest grades of the Porgera gold deposit, Papua New Guinea, are contained in Zone 7 due to the presence of the Roamane fault, which acted as channelway of the gold-bearing fluids. Prior to the development and underground mining of this fault-controlled high-grade zone it was critical to provide grade estimates of relatively small mining units, and of the proportion of mining units above cutoff. To be applicable to Zone 7 of Porgera a grade estimation method should account for the following:1. the highly skewed and apparently lognormal distribution of the grades,2. the rapid drop off of the local mean grade and the variance as the distance to the Roamane fault increases,3. the presence of high grade pockets in the footwall, away from that fault, and4. the existence of variograms for the logs with sills parallel to the fault and without sills perpendicular to it.

Jan 1, 1990

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

By Kim YC

An alternative development drilling strategy to the one currently in use at an open pit mine was investigated using geostatistics for a portion of the pit. The massive orebody, the 3-D nature of the problem, and the location of ultimate pit limit in the study area all created some unique problems in devising the development drilling strategy. Rather than using confidence interval of the global reserve estimate as the main criterion for development drilling, the confidence interval of short and medium range mine planning blocks was used as the objective. Based on somewhat arbitrarily selected level of confidence, the results from the study showed that a total of 50 diamond drillholes (DDHs) rather than the planned 62 DDHs is sufficient in the study area, if the selected confidence levels are acceptable to the management. The paper also emphasizes the importance of particular objectives being used in development drilling and how they influence the "optimal" placement of the development drillholes.

Jan 1, 1986

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

Good morning. I am very pleased to be invited to present the Opening Address to this inaugural New Zealand Minerals & Mining Conference. It is indeed a pleasure to see so many representatives of this industry, which is so important to New Zealand's economy, present here today.   I extend a warm welcome to all delegates, particularly those from outside New Zealand. To those of you who have travelled from offshore, please closely observe our industry, and do not hesitate to ask Crown Minerals staff here for any further information you may want. I trust you will soon come to the same conclusion that my two following speakers have; that New Zealand is a good investment destination, and further that many of you will decide to invest in New Zealand's minerals and mining industry.   In New Zealand the minerals industry - minerals, coal and petroleum - together constitute an approximate $2.5 billion per year business. In broad terms this is about 3% of our Gross Domestic Product.

Jan 1, 1997

By Ormsby W, Peters M, Van Gils H, Kehprens P, De Boorder H

The northern margin of the Arunta Block is characterized by a metasedimentary and volcanic sequence of lower metamorphic grade than that of the central Arunta Block. Whereas the Harts Ranges have granulite to amphibolite metamor- phic grades, the northern margin only reached greenschist to lower amphibolite facies. Most of the high grade area of the central Arunta Block appears to be unprospective, but the lower grade marginal fringe contains most mineral pros- pects to name a few: Barrow Creek, Molyhill and the Jervois Mine. Numerous smaller prospects occur in this marginal zone. Four major lithostratigraphic units can be recognized in the Jervois Mine area: 1. Gneissic Suite consisting of granitic and rhyolitic gneisses which are characterized by a distinct intersection lineation. 2. Metasedimentary Suite of cordierite- biotite schists and chlorite-biotite schists. 3. Mine Sequence, consisting of spotted schists with andalusite and cordierite, quartz- sericite-feldspar schists with distinct rhyo- litic remnants and quartz-sericite-feldspar schists which contain the lode horizons:

Jan 1, 1984

By Eggins SM, Crawford AJ, Maillet P

The Fiji Islands are remnants of a once continuous Solomon-Vanuatu-Fiji-Tonga volcanic arc (the Vitiaz arc), located at the boundary between the Indian-Australian and Pacific plates. They record a history of (i) arc volcanism the late Eocene to late Miocene, (ii) an extensive magmatic response to arc rifting (5.5-3.OMa) during which volcanism was dominated by shoshonitic to tholeiitic basalts, and as rifting continued, (iii) a transition from arc to intraplate volcanism. The Hunter Ridge-Hunter Fracture Zone separates the inactive South Fiji Basin from the actively spreading North Fiji Basin, and has been considered to be a transform zone, almost parallel to the motion vector of the Australian plate. However rocks dredged during the 1993 `Alize' cruise, from along the northern part of the Hunter Ridge are typical arc tholeiites, and therefore demand that subduction has occurred beneath the Hunter Ridge sometime during the last û 5Ma.

Jan 1, 1995

By Manlapig EV, Davis JJ

A methodology for modelling dense medium cyclones is presented for cyclones operating under conditions which avoid particle interference or apex crowding. Particle interference and apex crowding are shown to result in less efficient separations and represent undesirable regimes of dense medium cyclone operation. In order to avoid apex crowding, suitable medium to ore ratios and apex diameters should be used. Cyclone density differentials should be kept below approximately 400kg.m 3 to limit loss of efficiency due to excessive particle recirculation within the cyclone. The relationship between size-by-size partition curves shows that the flow split and density of the medium within a cyclone can be related to two new parameters, the pivot partition number and pivot density. The parameters are common to each partition curve in any set of size-by-size data and are mathematically related to the familiar performance characteristics, ecart probable (Ep) and separation density. The resulting expression confirms that the Ep and separation density are directly related.

Jan 1, 1986

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By J-H Shin, Y-S Jung, D-J Youn, G-J Bae

This research is to grope for a method to reduce high pore pressure taking place on tunnel shotcrete lining, especially in underwater tunnels, effectively by utilising a new concept of patternised pin drain. Accordingly, the patternised pin drain system is investigated numerically in order to confirm to the effect of reduction of pore pressure by the pin drain and its effective application. Installation of pin drain shows considerable reduction in the figure of pore pressure. It is found through 2D numerical modelling that the change of pore pressure, according to the shape and the location of pin drain, is sensitive by the sequences of the change of location > the change of length > the change of angle degree. In the results of investigation in 3D modelling, the pore pressure is the largest in the centre of the interval among pin drains, and it is possible to obtain an ideal degree of longitudinal angle and an interval by investigating pore pressure taking place on the lining.

Jan 1, 2008

Major exploration companies can have a problem with what to do with small precious metal ore bodies located through exploration programmes. Low tonnage, but high grade, ore bodies too small to justify in-house development.1.2 Ban Ban Mining is a Sunshine Coast based partnership with considerable expertise in mining and earthmoving which specializes in the mining of small/medium size ore bodies on behalf of the tenement holder on a profit sharing or royalty basis.1.3 The partnership's first successful venture has been the mining and vat leaching of a small 40,000 tonne ore body with a head grade of 5 gm/tonne gold and 32 gms/tonne silver, situated near Ban Ban Springs in southeast Queensland.1.4 This paper looks at the low cost vat leaching method of treatment, as an alternative to CIP and CIL in the processing of low tonnage/high grade precious metal ore bodies.

Jan 1, 1990

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982